Crestron DMPS3-4K-100-C Handleiding

Crestron Niet gecategoriseerd DMPS3-4K-100-C

Lees hieronder de 📖 handleiding in het Nederlandse voor Crestron DMPS3-4K-100-C (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

DO GUIDE

DMPS3-4K-50 Rear Panel Connections

DMPS3-4K-100-C Rear Panel Connections

Information about VGA, DM OUT, AUDIO OUT, LAN, and NET pin assignments follows.

DMPS3-4K-50/DMPS3-4K-100-C

3-Series® 4K DigitalMedia™ Presentation Systems

DO Install the Device

The Crestron® DMPS3-4K-50 and DMPS3-4K-100-C can be mounted into a rack, mounted under a table, or placed onto a at surface.

Mount into a Rack

The DMPS3-4K-50 and DMPS3-4K-100-C each occupy 1U of rack space. Using a #1 or #2 Phillips screwdriver, attach the two included rack ears to the

device. Then, mount the device into the rack using four mounting screws (not included).

Mount under a Table

Using a #1 or #2 Phillips screwdriver, attach the four included table mount brackets to the device. Then, attach the four table mount brackets to the underside

of the table using four mounting screws (not included).

Place onto a Flat Surface

When placing the device onto a at surface or stacking it with other equipment, attach the included feet near the corners on the underside of the device.

DO Connect the Device

Make connections to the rear panel of the device. Refer to the following illustrations for information about DMPS3-4K-50 and DMPS3-4K-100-C connections.

DO Check the Box

QUANTITY PRODUCT COLOR PART NUMBER

2 Bracket, Rack Ear, 1U 2032122

4 Bracket, Under Table Mount 2041951

1 Connector, 4-Pin 2003576

2 Connector, 5-Pin 2003577

1 Emitter Probe, IR, Crestron® STIRP 2001137

4 Foot, 0.5" x 0.5" x 0.23", Rubber 2002389Black

1 Power Cord, 6' 7" (2 m) 2001134

DMPS3-4K-100-C Only

1 Connector, 3-Pin 2003575

Ground

MIC IN:

From

microphone

AUDIO OUT:

To balanced/

unbalanced

stereo line

level audio

output device

IR OUT:

To Crestron

STIRP IR

emitter probe

(included)

COM:

RS-232

device

USB 1–4:

To Crestron

TT-100 series

presentation

interfaces

NET:

To Cresnet

device

DM OUT:

To DM 8G+®

receiver or other

DM® device or to

HDBaseT® device*

LAN:

10BASE-T/100BASE-TX

Ethernet to LAN 100-240V~1.4A

50/60 Hz:

From ac

power outlet

VGA 1–4:

From RGB (VGA),

component, S-video, or

composite video sources

AUDIO 1–4:

From unbalanced

stereo line level

analog audio sources

HDMI 1–4:

From HDMI

audio/video

sources

HDMI OUT:

To HDMI

display

VGA 1–4:

From RGB (VGA),

component, S-video, or

composite video sources

AUDIO 1–4:

From unbalanced

stereo line level

analog audio sources

HDMI 1–4:

From HDMI®

audio/video

sources

HDMI OUT:

To HDMI

display

AUDIO OUT:

To balanced/

unbalanced

stereo line

level audio

output device

IR OUT:

To Crestron

STIRP IR

emitter probe

(included)

COM:

RS-232

device

Ground

LAN:

10BASE-T/100BASE-TX

Ethernet to LAN

USB 1–4:

To Crestron

TT-100 series

presentation

interfaces

NET:

To Cresnet®

device

100-240V~1.4A

50/60 Hz:

From ac

power outlet

DO GUIDE DOC. 7897C (2046349) 02.18

Specications subject t o change without not ice.

VGA Connector Pin Assignments

DM OUT Connector Wiring (DMPS3-4K-100-C Only)

AUDIO OUT Pin Assignments

LAN Pin Assignments

NET Pin Assignments

DO Determine the Address of the Device

The device can be addressed using the hostname. The default hostname is DMPS3-xxxxxxxx, where

xxxxxxxx consists of the last eight characters (excluding punctuation) of the MAC address. For example,

if the MAC address is 00:10:7F:08:09:AA:05, the default host name is DMPS3-0809AA05. The MAC

address is labeled on the shipping box and rear panel of the device.

Alternatively, the device can be addressed using the IP address. By default, DHCP is enabled. To set a

static IP address, use Crestron Toolbox™ software on a PC that connects to the device via the Ethernet

network or a USB connection to the COMPUTER port on the front panel of the device. If the PC connects

to the Ethernet network, the Device Discovery Tool within the Crestron Toolbox software can be used to

nd the current IP address.

DO Commission the System

Using the web interface, congure the device. To access the web interface, open a web browser and go

to the setup directory of the device by entering either of the following:

hostname hostname/setup ( is the hostname of the device)

xxx.xxx.xxx.xxx/setup (xxx.xxx.xxx.xxx is the IP address of the device)

The device also provides the built-in .AV Framework™ program, which enables complete system control

without requiring additional programming. To access the .AV Framework conguration interface, open a

web browser and go to either of the following:

hostname hostname:8008 ( is the hostname of the device appended by :8008)

xxx.xxx.xxx.xxx:8008 (xxx.xxx.xxx.xxx is the IP address of the device appended by :8008)

For more information, go to www.crestron.com/avframework.

DO Connect to the Crestron XiO Cloud Service

The Crestron XiO Cloud service allows supported Crestron devices across an enterprise to be managed

and congured from one central and secure location in the cloud. Supported devices are precongured

to connect to the service. Use of the service requires a registered Crestron XiO Cloud account.

To connect the device to the Crestron XiO Cloud service, do the following:

1. Record the MAC address and serial number that are labeled on the shipping box or rear panel

of the device. The MAC address and serial number are required in order to add the device to

the Crestron XiO Cloud environment.

2. Do either of the following:

• If you have a Crestron XiO Cloud account, go to https://portal.crestron.io to access the

Crestron XiO Cloud service.

• If you do not have a Crestron XiO Cloud account, go to www.crestron.com/xiocloud to

For detailed information about using the Crestron XiO Cloud service, refer to the Crestron XiO Cloud

Service User Guide (Doc. 8214) at www.crestron.com/manuals.

DO Allow Automatic Switching or Manually Select an Input

By default, automatic switching of inputs is enabled. Automatic switching causes the last connected

input to be routed to the output. The AUTO LED lights to indicate that automatic switching is enabled.

To manually select and activate the desired input, press one of the (1–4) or VGA HDMI (1–4) INPUT

SELECT buttons. Refer to the following table for a summary of the LED behavior of selected and

nonselected inputs.

NOTE: Manual selection of an input disables automatic switching. When automatic switching is

disabled, the AUTO LED turns off.

*The DM OUT port of the DMPS3-4K-100-C is a PoDM and HDBaseT PoE power sourcing equipment (PSE) port. Any wiring that

is connected to a PoDM or HDBaseT PoE PSE port is for intrabuilding use only and should not be connected to a line that runs

outside of the building in which the PSE is located.

As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.

This product is Listed to applicable UL

® Standards and requirements tested by Underwriters Laboratories Inc.

Ce produit est homologué selon les normes et les exigences UL applicables par Underwriters Laboratories Inc.

Federal Communications Commission (FCC) Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION: Changes or modications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada (IC) Compliance Statement

CAN ICES-3(B)/NMB-3(B)

Rack Mounting Safety Precautions

• Elevated Operating Ambient Temperature: If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient temperature. Therefore, consideration should be

given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specied by the manufacturer.

• Reduced Airow: Installation of the equipment in a rack should be such that the amount of airow required for safe operation of the equipment is not compromised.

• Mechanical Loading: Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading.

• Circuit Overloading: Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration

of equipment nameplate ratings should be used when addressing this concern.

• Reliable Earthing: Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit (e.g., use of power strips).

Electrical Connection

“This product must be connected to an earthed mains socket-outlet.”

• Finland: “Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan.”

• Norway: “Apparatet må tilkoples jordet stikkontakt.”

• Sweden: “Apparaten skall anslutas till jordat uttag.”

The specic patents t hat cover Crestron products are listed at . The product warrant y can be found at .www.crestron.com/legal/patents www.crestron.com/legal/sales-terms-conditions-warranties

Cert ain Crestron products contain open source sof t ware. For specic information, please visit . www.crestron.com/legal/open-source-sof tware

Crest ron, the Crestron logo, 3-Series, .AV Framework, Cresnet , Crest ron Toolbox, DigitalMedia, DM, DM 8G+, and VT Pro-E are either trademarks or registered t rademarks of Crestron Electronics, Inc., in the United States and/or other countries. Apple and iPad are eit her t rademarks or registered

trademarks of Apple Inc. in the United States and/or other count ries. HDBaseT and the HDBaseT Alliance logo are either trademarks or registered trademarks of the HDBaseT Alliance in the United St ates and/or other countries. HDMI and the HDMI logo are either t rademarks or registered trademarks

of HDMI Licensing LLC in the United States and/or other countries. UL and the UL logo are eit her trademarks or registered trademarks of Underwriters Laboratories, Inc. in the Unit ed States and/or other countries. Ot her trademarks, registered trademarks, and t rade names may be used in t his

document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any propriet ary int erest in t he marks and names of ot hers. Crest ron is not responsible for errors in typography or photography.

This document was written by the Technical Publications department at Crest ron.

DO Learn More

Visit the website for additional information and the latest rmware

updates. To learn more about this product, use a QR reader application

on your mobile device to scan the QR images.

Crestron Electronics

15 Volvo Drive, Rockleigh, NJ 07647

888.CRESTRON | www.crestron.com

DMPS3-4K-100-C

DMPS3-4K-50

NUM. RGB YPbPr S-VIDEO COMPOSITE

1 R CPr

2 G Y Y

3 B Pb COMP

5 GND GND GND GND

6 RED_GND C_GNDPr_GND

7 GRN_GND Y_GND Y_GND

8 BLU_GND Pb_GND

13 H

14 V

NOTE: For best video performance, ground connections should be

kept separate. Do not connect ground wires to the connector shell.

The connector shell is reserved for the cable shield.

NUM. WIRE COLOR PIN

NUM. WIRE COLOR

1 Orange/White 5 Blue/White

2 6Orange Green

3 7Green/White Brown/White

4 8Blue Brown

SIGNAL

NAME

BALANCED

AUDIO OUTPUT

UNBALANCED

AUDIO OUTPUT

+ L+ L+ Out

- L- Open

G Shield/Ground Common Ground

+ R+ R+ Out

- R- Open

NUM. SIGNAL PIN

NUM. SIGNAL

1 5TX+ N/C

2 6TX- RX-

3 7RX+ N/C

4 8N/C N/C

24: Power, 24 Vdc (Red Wire)

Y: Data (White Wire)

Z: Data (Blue Wire)

G: Ground (Black Wire)

Pin 1Pin 8

+ +

––

Pin 1

Pin 8

COLOR DESCRIPTION

Solid green The input is the active selection, and an incoming signal is detected.

Flashing green The input is the active selection, but an incoming signal is not detected.

Solid amber The input is not the active selection, but an incoming signal is detected.

Off The input is not the active selection, and an incoming signal is not detected.

Pin 10

Pin 5 Pin 1

Pin 6

Pin 15 Pin 11

5 1

1115

AMP

Left

Right

+ -G + -

Unbalanced Output

L R

Shield

AMP

Left

Right

G +

Balanced Output

L R

Product specificaties

Merk:	Crestron
Categorie:	Niet gecategoriseerd
Model:	DMPS3-4K-100-C
Kleur van het product:	Zwart
Gewicht:	2900 g
Breedte:	439 mm
Diepte:	266 mm
Hoogte:	45 mm
Materiaal behuizing:	Metaal
AC-adapterfrequentie:	50/60 Hz
AC-adapter ingangsspanning:	100-240 V
Ondersteunde video-modi:	480i, 576i, 1080i, 1080p, 2160p
Aantal USB 2.0-poorten:	4
Formaat analoog signaal:	NTSC, PAL
HDCP:	Ja
Ingang stroom:	Ja
Audio-ingangen:	4
Ondersteunde grafische resoluties:	1920 x 1080 (HD 1080),1920 x 1200 (WUXGA),2560 x 1600 (WQXGA),3840 x 2160,4096 x 2160
VGA (D-Sub) invoer ports:	4
Impedantie:	75 Ohm
Rack-montage:	Ja
Frequentiebereik:	20 - 20000 Hz
RJ-45 ports hoeveelheid:	2
Signaal/ruis-verhouding:	108 dB
HDMI in:	4
Aantal HDMI-uitgangen:	1
Warmtedissipatie:	122 BTU/h
Stroomverbruik (typisch):	36 W
Bedrijfstemperatuur (T-T):	5 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent
Synchronisatie ingangsimpedantie:	2200 Ohm
Ingangsstroom AC-adapter:	1.4 A
Geschaalde resoluties:	1920 x 1080,2560 x 1600,3840 x 2160,4096 x 2160
Kanaal scheiding (1 kHz):	103 dB
Maximale pixelsnelheid:	300 MHz