Crestron AMP-2100-100 Handleiding

Crestron Receiver AMP-2100-100

Lees hieronder de ๐Ÿ“– handleiding in het Nederlandse voor Crestron AMP-2100-100 (2 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 42 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
DO GUIDE
AMP-150-70/AMP-150-100/AMP-225/AMP-1200-70/AMP-1200-100/
AMP-2100/AMP-2100-70/AMP-2100-100
Modular Ampli๎€Ÿers
The Crestronยฎ Modular Ampli๎€Ÿer Series can be con๎€Ÿgured for individual module use on a ๎€žat surface or
ganged together (one or more modules) with the slide-lock system for installation in a 1U rack space.
The ampli๎€Ÿers are functionally similar to each other with varying capabilities. For simplicity within this
guide, the term โ€œampli๎€Ÿerโ€ is used except where noted.
DO Assemble the Device
If a single ampli๎€Ÿer is to be used on a ๎€žat surface, refer to โ€œPlacing onto a Flat Surface.โ€ Otherwise,
continue below for instructions on creating an ampli๎€Ÿer assembly that can be placed in a standard
equipment rack. The only tools needed are a #1 or # 2 Phillips screwdriver, and a 1/4" nut driver.
Gang Ampli๎€Ÿers Together
Perform the following procedure to gang ampli๎€Ÿers together. Refer to the diagrams.
1. Remove the two screws securing rail 1 to the ampli๎€Ÿer (unit 1).
2. Remove rail 1 from unit 1 by sliding it off the side of the ampli๎€Ÿer.
3. Attach rail 1 to unit 2 using the three included Phillips-head screws. Make sure that the screw
holes on the underside of rail 1 are on the bottom.
NOTE: Do not remove rail 2.
4. Slide unit 1 into the unit 2 assembly.
5. Secure unit 1 to the unit 2 assembly with the two screws removed in step 1.
6. Repeat steps 1 through 5 for additional ampli๎€Ÿers.
Con๎€Ÿgure for Rack Installation
Before an ampli๎€Ÿer can be installed in a rack, additional hardware must be installed.
Assemble Faceplates
When an ampli๎€Ÿer or group of ampli๎€Ÿers is not wide enough to mount in a rack, faceplates must be
assembled to โ€œwidenโ€ the ampli๎€Ÿer to ๎€Ÿt. Assemble a faceplate by attaching an extrusion plate to a
quarter-width or half-width rack ear, as shown in the following diagrams. Secure the extrusion plate to
the rack ear using a 1/4" nut driver and the included nuts.
Attach Rack Ears to Ampli๎€Ÿers
Attach the faceplate bracket(s) or rack ears, as required, to the ampli๎€Ÿer(s). Refer to the following
diagram for details.
NOTE: Do not attach faceplates to rack ears that are attached to the length of the ampli๎€Ÿer.
DO Install the Device
Once assembled, the ampli๎€Ÿer can be mounted into a rack, mounted onto a ๎€žat surface, or placed onto
a ๎€žat surface.
Mount into a Rack
Each ampli๎€Ÿer occupies 1U of rack space. Using a #1 or #2 Phillips screwdriver, mount the device into
the rack using four mounting screws (not included).
Mount onto a Flat Surface
1. Install the wall mount brackets with three Phillips-head screws (included) per side.
2. Secure the ampli๎€Ÿer to a ๎€žat surface using four mounting screws (not included).
Place onto a Flat Surface
Attach the included feet to place the ampli๎€Ÿer(s) on a ๎€žat surface.
DO Check the Box
QUANTITY ITEM PART NUMBER
1 Attenuator Cover, Magnetic, Security 4525789
2 Bracket, Wall Mount 2046992
1 Connector, 5-Pin 2003577
1 Extrusion Plate, Half-Width 4525245
1 Extrusion Plate, Quarter-Width 4525244
4 Foot, 0.5" x 0.5" x 0.23", Adhesive 2002389
4 Nut, 04-40, Keps 2004878
1 Power Cord, 6' 7" (2 m) 2001134
1 Rack Ear, 1U, Half-Width 2046652
1 Rack Ear, 1U, Quarter-Width 2046651
6 Screw, 6-32 x 3/8", Undercut Head, Phillips 2007235
AMP-150-70, AMP-150-100, AMP-1200-70, and AMP-1200-100 Only
1 Connector, 2-Pin 2044402
AMP-225, AMP-2100, AMP-2100-70, and AMP-2100-100 Only
2 Connector, 2-Pin 2044402
Remove these
screws.
Unit 1
Rail 1
Unit 1 Rail 1
Unit 2
Rail 2
Rail 1
Unit 1 Unit 2 assembly
Unit 1
Unit 2 assembly
Quarter-size rack ear
(no faceplate attached) Half-size faceplate bracket
Quarter-size faceplate bracket Half-size faceplate bracket
DO GUIDE DOC. 7868E (2046973) 08.18
Speci๎€Ÿcations subject t o change without notice.
DO Connect the Device
Make the necessary connections as called out in the following diagrams. Connect power last.
CAUTION:
โ€ข Keep the device unplugged until all of the input and speaker wiring is complete.
โ€ข Check the speaker wires for shorts and frayed wiring around the SPEAKER OUT connectors.
NOTES:
โ€ข On the AMP-150 and AMP-1200, the left and right inputs are summed to the output of the
ampli๎€Ÿer.
โ€ข Ensure the unit is properly grounded by connecting the chassis ground lug to an earth ground
(building steel).
โ€ข To prevent overheating, do not operate this product in an area that exceeds the environmental
temperature range listed in the productโ€™s table of speci๎€Ÿcations on the Crestron website
(www.crestron.com/Products/audio/ampli๎€Ÿers/audio-ampli๎€Ÿers-modular-ampli๎€Ÿers).
When connecting an input signal, use either the RCA connection or the 5-pin terminal block connector.
The 5-pin terminal block connector can be connected to balanced and unbalanced sources. Refer to the
following diagrams for connecting a source.
DO Operate the Device
Apply Power
To turn the ampli๎€Ÿer and audio outputs on, connect the included power cord to the power connector on
the rear of the ampli๎€Ÿer.
LED Operation
The LEDs on the front panel provide the following information:
LED DESCRIPTION
PWR Green: The ampli๎€Ÿer is operating normally.
Amber: The ampli๎€Ÿer is asleep.
FAULT Red: There is a fault on the indicated channel.
SIGNAL Green: An audio signal is present.
Red: The audio signal is clipped.
Adjust the Signal Levels
WARNING: This ampli๎€Ÿer is capable of delivering high power to the loudspeakers. Please use caution
and adequate ear protection if listening to content at high volume levels, as continued exposure to high
sound pressure levels can cause permanent hearing impairment or loss.
Each input has its own signal level control that can be adjusted as necessary to balance the sound
between inputs or to accommodate different audio sources. To adjust the level of an input, follow this
procedure:
1. If the magnetic attenuator cover is installed, remove it from the front of the ampli๎€Ÿer.
2. Use a Phillips screwdriver to turn the knob clockwise to increase the signal level or
counterclockwise to reduce the signal level.
3. Attach the magnetic attenuator cover.
As of the date of manufacture, the product has been tested and found to comply with speci๎€Ÿcations for CE marking.
These products are Listed to applicable UL
ยฎ Standards and requirements tested by Underwriters Laboratories Inc.
Ces produits sont รฉnumรฉrรฉs aux normes applicables et les exigences UL par Underwriters Laboratories Inc.
This symbol indicates a potential shock hazard.
This equipment is not suitable for use in locations where children are likely to be present.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modi๎€Ÿcations not expressly approved by the manufacturer responsible for compliance could void the userโ€™s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
โ€ข Reorient or relocate the receiving antenna.
โ€ข Increase the separation between the equipment and receiver.
โ€ข Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
โ€ข Consult the dealer or an experienced radio/T V technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
Rack Mounting Safety Precautions
โ€ข Elevated Operating Ambient Temperature: If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient temperature. Therefore, consideration should be
given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) speci๎€Ÿed by the manufacturer.
โ€ข Reduced Air๎€žow: Installation of the equipment in a rack should be such that the amount of air๎€žow required for safe operation of the equipment is not compromised.
โ€ข Mechanical Loading: Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading.
โ€ข Circuit Overloading: Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration
of equipment nameplate ratings should be used when addressing this concern.
โ€ข Reliable Earthing: Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit (e.g., use of power strips).
Electrical Connection
โ€œThis product must be connected to an earthed mains socket-outlet.โ€
โ€ข Finland: โ€œLaite on liitettรคvรค suojamaadoituskoskettimilla varustettuun pistorasiaan.โ€
โ€ข : โ€œApparatet mรฅ tilkoples jordet stikkontakt.โ€Nor way
โ€ข : โ€œApparaten skall anslutas till jordat uttag.โ€Sweden
The speci๎€Ÿc patent s that cover Crestron products are listed at . The product warranty can be f ound at .ww w.crestron.com/legal/patents www.crestron.com/warrant y
Cert ain Crestron products cont ain open source sof t ware. For speci๎€Ÿc inf ormation, please visit . www.crestron.com/opensource
Crest ron and the Crestron logo are either trademarks or registered trademarks of Crestron Electronics, Inc., in t he United States and/or other countries. UL and the UL logo are either trademarks or regist ered trademarks of Underwriters Laboratories, Inc. in the United St ates and/or other countries.
Ot her t rademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crest ron disclaims any proprietary interest in the marks and names of ot hers. Crestron is not responsible for errors in typography
or photography.
This document was writ ten by the Technical Publications department at Crestron.
ยฉ2018 Crest ron Electronics, Inc.
DO Learn More
Visit the website for additional information and the latest ๎€Ÿrmware
update. To learn more about this product, use a QR reader application
on your mobile device to scan the QR images.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
AMP-150
AMP-1200 AMP-2100
AMP-225
AMP-150-70, AMP-150-100, and AMP-225 (AMP-150-100 shown)
POWER:
From ac power outlet
AUDIO IN:
From audio source
GroundSPEAKER OUT:
To speaker(s)
AMP-1200-100, AMP-1200-70, AMP-2100, AMP-2100-70, and AMP-2100-100 (AMP-2100-100 shown)
AUDIO IN:
From audio source
POWER:
From ac power outlet
GroundSPEAKER OUT:
To speaker(s)
Wiring for Balanced Input Wiring for Unbalanced Input
Right
Left
Shield
+
+
Right
Left
Jumpers
+
+


Product specificaties

Merk: Crestron
Categorie: Receiver
Model: AMP-2100-100

Heb je hulp nodig?

Als je hulp nodig hebt met Crestron AMP-2100-100 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Receiver Crestron

Handleiding Receiver

Nieuwste handleidingen voor Receiver