Creality BL Touch Handleiding

Creality Niet gecategoriseerd BL Touch

Lees hieronder de 📖 handleiding in het Nederlandse voor Creality BL Touch (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 4 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/1
2. Prepare Move axis Move Z-Move 0.1mm→ → →Rotate
the knob until the distance between them is about
0.1mm (as a sheet of A4 paper), write down the value
of A.
1.Prepare → Auto home,and wait until it stops.
3 . Control Motion-Z Offset write down the value of → →
B, then rotate the knob until it comes out as: C = B +
A . Return Control and Select Store settings .
4.Prepare—>Bed Leveling（Different 3D printers may
have different numbers of touching points for auto-
matic leveling.）
After the automatic leveling, user can do a trial print to
verify the leveling.
Operation：Print from TF →Model Test (Name and file
of the testing model shall be prepared by user.）
Test passed: leveling is completed and you can print
now;
Test failed:If model printing fails, please fine-tune
Probe Z Offset again and save settings until the print-
ing effect is good.
Note: Every machine has its own operation interface.
0.1mm
Main
Ender3 Bed Level Test
meilanz j-29h-107g.gc
huxingdz-69h-217g.gc
Robot-t10-71.8h-400g
Software Settings
1. Open Slicer.
3. Machine Settings.
4. Change “G28” to “G28G29” .
Note: The specific operation video can be watched at
the following link:
https://www.youtube.com/watch?v=2B4qdKdqJj4
2. Settings → Printer → Manage Printers.
1. Open progisp.exe
2. Select Chip “ATmega1284p”.
3. Click ...→ Set Low Value = D6 Highvalue = DC, ExtValue=FD →
Click Write and close the window.
4. load Flash Select *.hex file.(Please download the firmware →
for your printer model to the computer. The firmware download
link is: https://www.creality.com/download）
5. Click Auto to update firmware, wait until it finished, then close.
6. Unplug the ISP Pinboard from mainboard.
Manual
AUTO BED LEVELING SENSOR FOR 3D PRINTER
BL Touch
Connectors
Tie
Rack Pinboard A
BurnerISP Pinboard
M3*6 2PCS M3*8 2PCS
1.4
Application: Ender-5 | Ender-5S | Ender-5 Pro
Ender-3 | Ender-3S | Ender-3Pro | CR-10 | CR-10Mini
Packing List Platform Adjustment
Model Printing
Software Settings
Circuit Principle Update Firmware
8 bit
Creality V1
Mainboard
Apply to 8-bit motherboards
1. Unplug the screen cable, connect the pinboard
A to the screen port.
2. Insert the screen cable into 10 pins port.
3. Insert the connectors to the 3 pins port as the
sign shows.
4. Unplug the Z limit switch(Z-stop port), and
insert the connectors.
1. Connect ISP Pinboard and Burner.
2. Open the control box and find out the mainboard.
3. Insert the ISP Pinboard into the mainboard 2x3 pins as the sign
shows.
4. Insert the Burner into computer USB port.
Install BL touch
1. Insert connectors into 5 Pin Port.
2. Install BL Touch on the rack with 2 M3*6 screws.
3. Loosen all fan cover screws, install the BL Touch rack
on the corresponding position with 2 M3*8 screws.
4. Tie the BL Touch cable together with other printer
cables like the above picture shown.
cable

Product specificaties

Merk: Creality
Categorie: Niet gecategoriseerd
Model: BL Touch

Heb je hulp nodig?

Als je hulp nodig hebt met Creality BL Touch stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Creality

Creality

Creality BL Touch Handleiding

5 Februari 2025

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Physa

Physa PHY-ND-1 Handleiding

5 Februari 2025
AVM

AVM PC 5.3 Handleiding

5 Februari 2025
CTA Digital

CTA Digital PAD-PARAFWK Handleiding

5 Februari 2025
USL

USL VCC-102 Handleiding

5 Februari 2025
USL

USL LSS-100P Handleiding

5 Februari 2025
USL

USL JSD-80 Handleiding

5 Februari 2025
USL

USL DAT-100 Handleiding

5 Februari 2025
USL

USL JSD-60 Handleiding

5 Februari 2025
Induction Dynamics

Induction Dynamics A2 Handleiding

5 Februari 2025
USL

USL DAX-202 Handleiding

5 Februari 2025