Cramer A82TXHD Handleiding

Cramer Niet gecategoriseerd A82TXHD

Lees hieronder de 📖 handleiding in het Nederlandse voor Cramer A82TXHD (48 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/48
cramer.eu
2902986 (Hedge trimmer)
EN | DE | ES | IT | FR | PT | NL | RU| FI | SV | NO| DA| PL | CS | SK | SL| HR| EL|
AR | TR | LT | LV | ET |
2cramer.eu
EN
Product Overview
Your machine has been engineered and manufactured to high standard for
dependability, ease of operation, and operator safety. When properly cared for, it
will give you years of trouble-free performance.
Know your Pole Hedge Trimmer Head
1. Blade
2. Pivot Button
3. Scabard
4. Auxiliary handle
5. Rubber protector
6. Lower shaft
7. Release button
8. knob
Assembly
•This product requires assembly.
•Carefully remove the product and any accessories from the box. Make sure
that all items listed in the packing list are included.
•Inspect the product carefully to make sure no breakage or damage
occurred during shipping.
•Do not discard the packing material until you have carefully inspected and
satisfactorily operated the product.
Install the Pole Hedge Trimmer Head (See Figure 2)
1 Remove the rubber protector.
2 Loosen the knob on the coupler.
3 Push in the release button located on the lower shaft. Align the release
button with the positioning hole and slide the two shafts together. Rotate the
lower shaft until the button locks into the positioning hole.
4 Tighten the knob securely.
NOTE: If the button does not release completely in the positioning hole, the
shafts are not locked into place. Slightly rotate from side to side until the button is
locked into place.
Adjust the Trimmer Head Angle (See figure 3)
The trimmer head pivots 180° and can be locked into 13 positions within that range.
1 Hold the auxiliary handle.
2 Pull back and hold the pivot button.
3 Use the auxiliary handle to adjust the trimmer head angle.
4 Release the pivot button once the trimmer head is in the desired position.
5 The trimmer head should lock securely in place.
Operation
Tips for Optimum Use (See figure 4-5)
•Start by trimming the top of the hedge. Slightly tilt the tool (up to 15° relative
to the line of cut) so that the blade tips point slightly towards the hedge. This
will cause the blades to cut more effectively. Hold the tool at the desired
angle and move it steadily along the line of cut. The doublesided blade allows
you to cut in either direction.
•In order to obtain a very straight cut, stretch a piece of string along the length
of the hedge at the desired height. Use the string as a guideline, cutting just
above it.
•In order to obtain flat sides, cut upwards with the growth. Younger stems
move outwards when the blade cuts downwards, causing shallow patches
in the hedge.
•Take care to avoid any foreign objects. Especially avoid hard objects such as
metal wire and railings, as these could damage the blades.
•Regularly oil the blades.
Maintenance
Clean the Machine
Clean the machine thoroughly to remove all dust and debris, after every work session.
•To reduce fire hazards, keep the machine and, in particular, the motor free
of leaves, branches or excessive grease.
•Always clean the machine after use with a damp cloth dipped in neutral
detergent.
•Remove all traces of humidity using a soft damp cloth. Humidity can
generate risks of electric shocks.
3
cramer.eu
EN
•Do not use aggressive detergents or solvents to clean the plastic parts or
handgrips.
•Do not spray water onto the motor and electrical components and prevent
them from getting wet.
•To avoid overheating and damage to the motor or the battery, always keep
the cooling air vents clean and free of debris.
Clean and Lubrication of the Cutting Means
To increase the efficiency and working life of the blades, clean and lubricate them
carefully after each work session:
•Place the machine in a stable horizontal position on the ground.
•Use a soft cloth to clean the blades, along with a brush to remove more
difficult dirt and debris.
•Lubricate the blades by applying a light layer of specific oil, preferably the
non-pollutant type, along the upper edge of the blade.
•Keep all nuts, bolts and screws tight to be sure the equipment is in safe
working condition.
•Check regularly that the handles are fixed firmly.
Troubleshooting
PROBLEM PROBABLE
CAUSE POSSIBLE SOLUTION
With the safety
lock button and
trigger on, the
cutting means
does not turn.
The machine is
damaged.
Do not use the machine. Immediately turn
off the machine remove the battery and
Contact a Service Centre.
The cutting means
overheats whilst
working.
Insufcient
blade
lubrication.
Turn off the machine, wait until the cutting
means is stationary, remove the battery
and lubricate the blades.
Excessive noise
and/or vibration is
experienced whilst
working.
Loose or
damaged parts.
Turn off the machine, remove the battery
and:
– inspect for damage;
– check for and tighten any loose parts;
– have any damaged parts replaced or
repaired with parts having equivalent
specications.
The machine gives
off smoke whilst
working.
The machine is
damaged.
Do not use the machine. Immediately turn
off the machine remove the battery and
Contact a Authorised Service Centre.
Technical Data
PROPERTY VALUE
Cutting length 466 mm

Product specificaties

Merk: Cramer
Categorie: Niet gecategoriseerd
Model: A82TXHD

Heb je hulp nodig?

Als je hulp nodig hebt met Cramer A82TXHD stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Cramer

Cramer

Cramer A82TXT Handleiding

8 April 2024
Cramer

Cramer 48SK192 Handleiding

8 April 2024
Cramer

Cramer A82TXHD Handleiding

8 April 2024
Cramer

Cramer A82TXPS Handleiding

8 April 2024
Cramer

Cramer 48SK96 Handleiding

8 April 2024
Cramer

Cramer A82TXE Handleiding

8 April 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Wiesenfield

Wiesenfield WIE-SC-200 Handleiding

17 December 2024
Wiesenfield

Wiesenfield WIE-CNB-130 Handleiding

17 December 2024
Wiesenfield

Wiesenfield WIE-CNB-140 Handleiding

17 December 2024
Wiesenfield

Wiesenfield WIE-CNB-110 Handleiding

17 December 2024
Wiesenfield

Wiesenfield WIE-FT-100 Handleiding

17 December 2024
Wiesenfield

Wiesenfield WIE-B-202 Handleiding

17 December 2024
Wiesenfield

Wiesenfield WIE-RH-500 Handleiding

17 December 2024
Wiesenfield

Wiesenfield WIE-BM-100 Handleiding

17 December 2024
Steinberg

Steinberg SBS-NL-240PLUS Handleiding

17 December 2024
Steinberg

Steinberg SBS-UH-140 Handleiding

17 December 2024