Conair LWD1RN Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Conair LWD1RN (2 pagina's) in de categorie Scheerapparat. Deze handleiding was nuttig voor 9 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Twin Fl
shaver
For your safety and continued enjoyment of this product,
always read the instruction book carefully before using.
MODEL LWD1RN
Congratulations on the purchase of your
new twin-foil wet/dry shaver for women.
For maximum satisfaction when using this
quality product, please take a minute to read
the following operating and care instructions.
Thank you for choosing Conair, the #1 brand in
personal care appliances.
SAVE THESE
INSTRUCTIONS
WARNING
1. Women whose skin is sensitive to cosmetics
or easily irritated by shaving, or who suffer from
a skin allergy, should test one section of the
leg or arm before using the shaver.
2. The foils are thin and precisely finished
pieces. Do not press hard against the
foils or drop foils. A warped or distorted
foil will produce poor shaving results.
Also, a damaged foil may cause skin
injury. A damaged foil should be
replaced immediately.
3. When cleaning, use cold or warm water.
Do not use hot water, seawater, or cleaners, as
they can cause damage to the waterproof seals.
4. Do not leave the entire unit submerged in
water for a long period of time.
5. To prevent possible damage to the foils and
the cutter, women who use underarm deodorant
must thoroughly clean and air-dry the foils and
cutter after each use. Failure to do this may
result in corrosion of the inner blades.
6. This appliance is not a toy. Keep away from
children.
OPERATING
INSTRUCTIONS
IMPORTANT
This shaver has been engineered to give you a
clean, close, smooth shave. It requires 2 AAA
batteries (not included). We recommend using
longer lasting alkaline batteries in your shaver.
If you are not going to use your shaver for a
long period of time or if the batteries are dead,
remove or replace the batteries from the unit.
Use your shaver exclusively for three to four
weeks so that your legs and underarms adjust
to the shaver. At first, your shave might not be
as close as you expect. However, this is normal.
It takes time for your skin and hair to adjust to
the new procedure and for you to learn how to
effectively use the shaver.
Caution: Most blade users will push too hard
and therefore not get a satisfactory shave. You
must press gently so the hair can get into the
holes of the foils. Pressing too hard makes the
hair flat. Please be patient; use your shaver 10
to 12 times before you judge its performance.
FOR HOUSEHOLD
USE ONLY
OPERATING INSTRUCTIONS
1. Remove the battery compartment cover by
pushing in and down toward the bottom of the
shaver.
2. Align the 2 AAA batteries with the positive
and negative positions indicated inside the
battery compartment. Being careful not to bend
the clips, insert the negative end of each battery
first so it will slip easily into place.
3. Return the battery cover to its original
position by pushing it in and up until you hear a
small click as it locks into place.
4. To use your shaver, remove the transparent
cover and push ON/OFF switch upwards to the
ON position.
5. After you finish using your shaver, push down
on the ON/OFF switch to turn the shaver off.
6. Ensure the batteries are installed correctly
with regard to polarity (+ and -).
7. Remove the batteries if they are no longer
functional or if the shaver is left unused for an
extended period of time.
8. Clean the battery contacts and also those of
the device prior to battery installation.
9. Remove used batteries promptly.
10. Always purchase the correct size and grade
of battery most suitable for the intended use.
11. Replace all batteries of a set at the same
time.
12. Do not mix old and new batteries. Do
not mix alkaline, standard (carbon-zinc), or
rechargeable (nickel cadmium or nickel metal
hydride) batteries.
CAUTION
Do not immerse any part of the unit in water or
other liquid.
The outer foils and cutters are delicate and
must be handled very carefully.
BEFORE SHAVING
1. Before wet shaving, you may wish to prepare
your legs and underarms with shaving cream
or soap. If a soapy lather is applied to the skin,
the shaver will glide smoothly over the skin and
clean away oil residue, while at the same time
removing hair. Caution: Do not use shaving
gels, as these products can clog your
shaver foils.
2. When dry shaving, be certain that your skin
is clean. If you have sensitive skin, you may
want to apply talcum powder before and after
you shave.
3. Clean your shaver after each use. This will
ensure the best performance. (Please refer to
“How to Clean Your Shaver section for further
instructions.)
INSTRUCTIONS
FOR USE
1. Slide the main switch up to the ON position.
2. After each shave, switch the unit off and
clean shaver head.
SHAVING YOUR
LEGS/BIKINI AREA
NOTE: Pushing the shaver against the skin too
hard will not allow the hairs to enter the foils
and be cut. Experience will help you determine
just the right pressure to use to maximize
performance.
1. Prepare your legs for wet or dry shaving.
2. Turn shaver on.
3. Shave with smooth, steady strokes up and
down your skin.
4. Keep the full shaving head in contact with
your skin.
5. For best results, shave against the direction
of hair growth.
6. The shaver also has a bikini pop-up trimmer
for your complete shaving needs.
7. When you finish shaving, turn the shaver off.
Important: After several uses, you will be able
to determine the optimum shaving method for
your legs and bikini area.
SHAVING YOUR UNDERARMS
1. Prepare your underarms for wet or dry
shaving. (Be sure that your skin is clean and
free of deodorant.)
2. Turn the shaver on.
3. Lift your arm until the skin under the arm
stretches slightly.
4. Use the trimmer portion first to remove any
long hair, stroking trimmer against the direction
of hair growth.
5. Hold the shaver so that it is in full contact
with your skin, and shave with gentle strokes.
6. It is important to press lightly. Pressing too
hard may lead to skin irritation.
7. When finished shaving, turn the shaver off.
Important: After several uses, you will be able
to determine the optimum shaving method for
your underarms.
HOW TO CLEAN YOUR SHAVER
1. Make sure unit is in the OFF position before
cleaning your shaver.
2. Hold shaver head and lift up from the back,
then press foil frame release buttons on each
side and lift up (the cutter is now in view).
Be careful not to push on the foils. They are
delicate and can easily be damaged. (FIG.1)
3. Rinse the shaver cutter and foil frame under
running water or in a sink. Do not use hot water.
Use only warm or cold water.
4. After rinsing, allow the foil frame and cutters to
air-dry before closing foil frame and shaver head.
Replace shaver head back onto the shaver until
it clicks into place. Wipe the surface of the main
unit with a dry towel. Do not dry the foil area. Let
the shaving head air-dry.
5. The cutters can also be cleaned with a
cleaning brush.
6. If the body of the shaver becomes dirty, wipe
off with a damp cloth and mild detergent or
soap. Never use thinners, other solvents, or any
harsh cleaners.
7. Once dried, carefully place the protective cap
on.
CAUTION
1. When shaking off excess water, hold the
main unit firmly to prevent releasing the head
assembly or dropping the unit.
2. Do not use a dryer or heater to dry the
shaver. This may result in malfunction or
damage to the shaver.
NOTE: At the end of the batteries useful life,
under various state and local laws, it may be
illegal to dispose of these batteries into the
municipal waste stream. Check with your local
solid waste officials for details on recycling
options or proper disposal in your area.
Press Here
FIG. 1
Press Here
Transparent cover
Pop-up button
REPLACING THE
FOIL FRAME & CUTTERS
Replace the foil frame when you find you have
to push harder on the shaver to get a close
shave, or if you have to go over your leg area
more often to get a smooth result. It is also
time to replace the foils if you experience skin
irritation. Replacement time will depend on how
often you use your shaver and how quickly your
hair grows.
Caution: Never replace the cutters without
replacing the foils as well.
1. Remove the foil frame (see FIG. 2).
FIG. 2
Lift
Press Here
Press Here
2. Push one side of the inner blade to unlock it
and take out (see FIG. 3).
spring
FIG. 3
Hold Here
Hold Here
spring
Caution: Make sure you do not lose the little
spring under the cutter, as it will be needed
for the new cutter (see FIG. 4).
3. Hold the new inner blades firmly on the
sides and guide them gently into the inner
blade mount, one side at a time, until they lock
into place.
4. Press firmly until the unit snaps into place.
5. Replace the foil frame (see FIG. 5).
FIG. 5
REPLACING THE POP-UP
TRIMMER ASSEMBLY
Note: We do not recommend replacing the
trimmer assembly yourself. Take or send the
shaver to a Conair Service Center, because this
requires a special tool for replacement. For
most users, these trimmers will stay sharp for
as long as you own your shaver.
FIG. 4
LIMITED TWO-YEAR WARRANTY
(U.S. AND CANADA ONLY)
Conair will repair or replace (at our option) your
unit free of charge for 24 months from the date
of purchase if the appliance is defective in work-
manship or materials.
To obtain service under this warranty, return
the defective product to the service center listed
on back, together with your purchase receipt.
California residents need only provide proof of
purchase and should call 1-800-3-CONAIR for
shipping instructions. In the absence of a pur-
chase receipt, the warranty period shall be 24
months from the date of manufacture.
ANY IMPLIED WARRANTIES, OBLIGATIONS,
OR LIABILITIES, INCLUDING BUT NOT
LIMITED TO THE IMPLIED WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, SHALL BE LIMITED IN
DURATION TO THE 24-MONTH DURATION OF
THIS WRITTEN, LIMITED WARRANTY. Some
states do not allow limitations on how long an
implied warranty lasts, so the above limitations
may not apply to you.
IN NO EVENT SHALL CONAIR BE LIABLE
FOR ANY SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES FOR BREACH OF
THIS OR ANY OTHER WARRANTY, EXPRESS
OR IMPLIED, WHATSOEVER. Some states do
not allow the exclusion or limitation of special,
incidental, or consequential damages, so the
above limitation may not apply to you.
This warranty gives you specific legal rights, and
you may also have other rights, which vary from
state to state.
For shaving tips and information on Conair
appliances, call or visit us on the 1-800-3-CONAIR
web at www.conair.com
REPLACEMENT PARTS:
This shaver uses the following replacement
parts, which can be ordered directly from Conair
by calling customer service at 1-800-3-CONAIR.
CSP21 Replacement Foil and Cutter
Please register this product at
www.conair.com/registration
Service Center
©2021 Conair Corporation
Service Department
7475 North Glen Harbor Blvd.
Glendale, AZ 85307
stock.image
20PG074867 IB-16969
Afeitada de
doble hoja
Para su seguridad y para disfrutar plenamente de este
producto, siempre lea cuidadosamente las
instrucciones antes del uso.
MODELO LWD1RN
Le felicitamos por su compra de esta afeitadora
de doble hoja para afeitado en húmedo/seco.
Para su máxima satisfacción y para conseguir
resultados óptimos con este producto de
calidad, siempre lea las instrucciones de
uso y mantenimiento que se encuentran a
continuación. Gracias por haber elegido a
Conair, la marca n.° 1 en aparatos de cuidado
personal.
GUARDE ESTAS
INSTRUCCIONES
ADVERTENCIA
1. Si su piel es sensible a los productos
cosméticos, se irrita fácilmente cuando se
afeita o padece de alergia, pruebe el aparato en
una pequeña sección del brazo o de la pierna
antes del primer uso.
2. Las hojas de afeitar son delgadas y
precisas. No las apriete mucho contra la
piel, ni las deje caer. Una hoja dañada o
deformada impedirá el buen funcionamiento
del aparato,
y puede causar heridas. Reemplace las
hojas defectuosas inmediatamente.
3. Limpie el cabezal en agua fría o tibia
solamente.
No use agua caliente, agua salina o
limpiadores; esto puede dañar los sellos de
impermeabilidad del cabezal.
4. No sumerja el aparato en agua por un tiempo
prolongado.
5. Si usa desodorante, lave cuidadosamente y
deje secar las hojas y las cuchillas internas al
aire después de cada uso. Si no lo hace, las
cuchillas internas se pueden oxidar.
6. Este aparato no es un juguete; manténgalo
fuera del alcance de los niños.
INSTRUCCIONES
DE OPERACIÓN
IMPORTANTE
Este aparato p2-ha sido diseñado para proporcionar
un afeitado al ras suave y preciso. Requiere
2 pilas AAA (no incluidas). Le aconsejamos
que use pilas alcalinas, las cuales son más
duraderas. Retire las pilas las pilas gastadas, o
si no va a usar la unidad por un largo período
de tiempo.
Durante tres a cuatro semanas, use
exclusivamente esta afeitadora para afeitar sus
piernas/axilas. Puede que sus primeros intentos
no sean perfectos; esto es normal. La piel y los
vellos necesitan tiempo para acostumbrarse a
una nueva técnica de afeitado.
Precaución: Muchas personas presionan
demasiado las hojas contra la piel y, por lo
tanto, no obtienen resultados satisfactorios.
Se debe presionar suavemente, para dejar que
los vellos entren en los orificios en las hojas;
presionar demasiado aplasta los vellos. Sea
paciente; use el aparato 10 a 12 veces antes de
evaluar su rendimiento.
PARA USO DOMÉSTICO
SOLAMENTE
INSTRUCCIONES DE OPERACIÓN
1. Presione y deslice la tapa del compartimiento
de las pilas hacia abajo para abrirlo.
2. Instale 2 pilas AAA, respetando los signos de
polaridad indicados en el compartimiento de
las pilas. Introduzca el polo negativo de cada
pila primero, teniendo cuidado de no doblar las
patas de contacto.
3. Cierre la tapa del compartimiento de las
pilas, empujando hacia dentro y hacia arriba
hasta que haga clic y se bloquee en su lugar.
4. Para usar el aparato, quite la tapa
transparente y deslice el botón de encendido/
apagado hacia arriba (“ON”).
5. Para apagar el aparato, deslice el botón de
encendido/apagado hacia abajo (“OFF”).
6. Siempre respete los signos de polaridad (+/-)
al instalar las pilas.
7. Retire las pilas las pilas gastadas/agotadas,
o si no va a usar la unidad por un largo período
de tiempo.
8. Limpie los contactos del aparato y los de las
pilas antes de instalarlas.
9. Retire las pilas gastadas/agotadas sin
demora.
10. No use pilas que no sean del tamaño ni
de la potencia indicados para uso con este
aparato.
11. Cambie todas las pilas al mismo tiempo.
12. No junte pilas nuevas con pilas usadas.
No junte pilas alcalinas con pilas regulares
(carbono-zinc) o pilas/baterías recargables
(NiCd o Ni-MH).
PRECAUCIÓN
No sumerja ninguna pieza del aparato en agua
u otro líquido.
Las hojas de afeitar y las cuchillas internas
son delicadas y deben manipularse con mucho
cuidado.
ANTES DEL AFEITADO
1. Es recomendable aplicar crema de afeitar
o jabón en sus piernas y axilas antes de
afeitarse en húmedo; esto facilitará el afeitado
y eliminalos residuos de aceite de la piel al
mismo tiempo que los vellos. Precaución: NO
use gel de afeitar, p2-ya que los geles pueden
obstruir las hojas.
2. Antes del afeitado en seco, cerciórese de
que la piel está limpia. Si su piel es sensible,
puede aplicar talco antes y después del afeitado
si desea.
3. Limpie la afeitadora después de cada
uso; esto asegurará un rendimiento óptimo.
Para más información, véase la sección
“Instrucciones de limpieza”.
INSTRUCCIONES
DE USO
1. Para encender el aparato, ponga el botón de
encendido/apagado en la posición de encendido
(“ON”).
2. Después de cada uso, apague la unidad y
limpie el cabezal de afeitado.
CÓMO AFEITAR
SUS PIERNAS/INGLES
NOTA: Presionar las hojas demasiado contra
la piel aplasta los vellos e impide que entren
en las hojas para ser cortados. La experiencia
le ayudará a determinar exactamente cuánta
presión aplicar para obtener resultados óptimos.
1. Prepare la piel para el tipo de afeitado
deseado, en húmedo o en seco.
2. Encienda la unidad.
3. Mueva laquina suavemente contra la piel,
hacia arriba y abajo.
4. Siempre mantenga el cabezal en pleno
contacto con la piel.
5. Para conseguir resultados óptimos, aféitese
en dirección contraria al crecimiento del vello.
6. La máquina de afeitar también cuenta con
una cuchilla recortadora desplegable para
acortar el vello largo.
7. Después de terminar, apague el aparato.
Importante: Necesitará hacer varios intentos
hasta encontrar la mejor manera de afeitar sus
piernas/ingles.
CÓMO AFEITAR SUS AXILAS
1. Prepare la piel para el tipo de afeitado
deseado, en húmedo o en seco. Cerciórese
de que la piel está limpia, seca y libre de
desodorante.
2. Encienda la unidad.
3. Levante el brazo para estirar ligeramente la
piel.
4. Si el vello es largo, acórtelo con la cuchilla
recortadora integrada, pasando la máquina en
dirección contraria al crecimiento del vello.
5. Mantenga el cabezal en pleno contacto
con la piel y afeite los vellos con movimientos
suaves.
6. Es importante que presione ligeramente;
hacer mucha presión puede causar irritación
de la piel.
7. Después de terminar, apague la unidad.
Importante: Necesitará hacer varios intentos
para determinar el método óptimo para afeitar
sus axilas.
INSTRUCCIONES DE LIMPIEZA
1. Cerciórese de que la unidad está apagada
(posición “OFF”).
2. Sosteniendo firmemente la unidad,
oprima los botones de liberación situados en
ambos lados del cabezal y levante este; las
cuchillas internas quedarán al descubierto.
Tenga cuidado de no presionar las hojas; son
delicadas y pueden dañarse fácilmente. (FIG.1)
Presionar aquí
FIG. 1
Presionar aquí
Cubierta transparente
Botón de
liberación
3. Enjuague las cuchillas internas y las hojas
en agua corriente. No use agua caliente; use
solamente agua tibia o fría.
4. Después de enjuagar las cuchillas y las
hojas, permita que se sequen al aire antes de
volver a ensamblar el cabezal. Una vez seco,
vuelva a instalar el cabezal, presionando hasta
que haga clic y encaje en su lugar. Seque la
carcasa del aparato con una toalla seca. No
seque el área de la hoja; permita que el cabezal
se seque al aire.
5. Si desea, use un pequeño cepillo para limpiar
las cuchillas internas.
6. Si la carcasa del aparato es sucia, límpiela
con un paño ligeramente humedecido con
agua jabonosa o detergente suave. Nunca use
disolventes, solventes o limpiadores fuertes.
7. Una vez seco, vuelva a colocar la cubierta
protectora sobre el cabezal.
PRECAUCIÓN
1. Si tiene que sacudir la unidad para eliminar
el exceso de agua, sosténgala firmemente para
no dejarla caer ni desarmar el cabezal.
2. No use un secador ni un calentador para
secar la unidad; esto puede dañarlo o impedir
su buen funcionamiento.
NOTA: Dependiendo de las normas regionales o
locales vigentes, puede que sea ilegal tirar las
pilas/baterías con el resto de la basura al final
de su vida útil. Compruebe con las autoridades
locales las opciones de reciclaje disponibles en
su lugar de residencia.
CÓMO REEMPLAZAR LAS HOJAS
Y LAS CUCHILLAS INTERNAS
Si siente que debe hacer fuerza para afeitarse
o si debe pasar la afeitadora en la misma
zona varias veces para conseguir un resultado
suave, cambie las cuchillas internas. Asimismo,
cambie las hojas si nota que irritan la piel.
La frecuencia de reemplazo dependerá de la
frecuencia de uso del aparato y de la velocidad
de crecimiento del vello.
Precaución: Siempre reemplace las hojas y las
cuchillas internas al mismo tiempo.
1. Quite el cabezal (FIG. 2).
FIG. 2
Levantar
Presionar aquí
Presionar aquí
2. Presione el costado de las cuchillas internas
para liberarlas y sacarlas (FIG. 3).
resorte
FIG. 3
Sostener aquí
Sostener aquí
resorte
Precaución: Tenga cuidado de no perder
el pequeño resorte situado debajo de las
cuchillas internas; lo necesitará para instalar
las nuevas cuchillas internas (FIG. 4).
FIG. 4
3. Sostenga firmemente las cuchillas internas
por los costados e insértelas suavemente en
el soporte interno, un lado tras otro, hasta que
encajen
4. Presione firmemente hasta que la unidad
encaje.
5. Vuelva a instalar el cabezal (FIG. 5).
FIG. 5
CAMBIO DE LA CUCHILLA
RECORTADORA DESPLEGABLE
Nota: No le aconsejamos que intente
reemplazar la cuchilla recortadora integrada/
desplegable. Se necesita una herramienta
especial para hacer esto. Si la cuchilla está
dañada o no corta, devuelva el aparato a un
centro de servicio autorizado. Sin embargo,
la cuchilla p2-ha sido diseñada para durar tanto
tiempo como la unidad, y es probable que
nunca la tenga que reemplazar durante la vida
útil de la afeitadora.
GARANTÍA LIMITADA DE DOS AÑOS
(VÁLIDA EN LOS EE.UU. Y EN
CANADÁ SOLAMENTE)
Conair reparará o remplaza (a su opción) este
producto sin cargo por un período de 24 meses a
partir de la fecha de compra si presenta defectos
de fabricación o materiales.
Para obtener servicio técnico bajo esta garantía,
devuelva el producto defectuoso al Centro de
Servicio indicado en el reverso, junto con su rec-
ibo de compra. Los residentes de California solo
necesitan dar una prueba de compra y deben lla-
mar al 1-800-3-CONAIR para recibir instrucciones
de envío. En ausencia del recibo de compra, el
período de garantía será de 24 meses a partir de
la fecha de fabricación.
CUALQUIER GARANTÍA, OBLIGACIÓN O
RESPONSABILIDAD IMPLÍCITAS, INCLUYENDO,
PERO NO LIMITADAS A LA GARANTÍA
IMPLÍCITA DE COMERCIABILIDAD Y APTITUD
PARA UN PROPÓSITO ESPECÍFICO, ESTARÁN
LIMITADAS POR LOS 24 MESES DE LA
PRESENTE GARANTÍA ESCRITA. Algunos Estados
no permiten limitaciones en la duración de una
garantía implícita, de modo que las limitaciones
mencionadas pueden no regir para usted.
CONAIR NO SERÁ RESPONSABLE, EN NINGÚN
CASO, POR NINGÚN DAÑO ESPECIAL,
INCIDENTAL O CONSECUENTE DEBIDO AL
INCUMPLIMIENTO DE ESTA O CUALQUIER OTRA
GARANTÍA, EXPRESA O IMPLÍCITA. Algunos
Estados no permiten la exclusión o limitación de
daños especiales, incidentales o consecuentes,
de modo que las limitaciones mencionadas
pueden no regir para usted.
Esta garantía le otorga derechos legales espe-
cíficos y usted puede tener otros derechos que
varían de un Estado a otro.
Para conseguir consejos de afeitado o s
información sobre los productos Conair
®, llame al
1-800-3-CONAIR www.conair.como vitenos en
REPUESTOS
Para pedir repuestos (véase la lista de las
piezas disponibles a continuación), llame al
1-800-3-CONAIR.
Hojas y cuchillas internas (modelo CSP21)
Para registrar su producto,
visítenos en:
www.conair.com/registration
Centro de servicio
©2021 Conair Corporation
Service Department
7475 North Glen Harbor Blvd.
Glendale, AZ 85307
Fotografía de banco de imágenes
20PG074867 IB-16969


Product specificaties

Merk: Conair
Categorie: Scheerapparat
Model: LWD1RN

Heb je hulp nodig?

Als je hulp nodig hebt met Conair LWD1RN stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Scheerapparat Conair

Handleiding Scheerapparat

Nieuwste handleidingen voor Scheerapparat