Conair GS95 Handleiding

Conair Stoomreiniger GS95

Lees hieronder de 📖 handleiding in het Nederlandse voor Conair GS95 (2 pagina's) in de categorie Stoomreiniger. Deze handleiding was nuttig voor 37 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

6. With telescopic pole now fully assembled,

place the T-Nozzle onto holder above the

hanger.

7. When you are ready to steam, fill the water

tank from the top opening. Note, do not open

the bottom cap as this is used for cleaning or

removing excess water only.

8. Plug the steamer unit into a standard 120V

AC power outlet.

9. The bristle brush attachment easily

snaps over the T-nozzle for use. To use the

creaser attachment, simply line up at base

and slide into back under T-nozzle and push

firmly to attach. See instruction booklet

"Attachments" section figures 5 and 6

for more details.

TURNING STEAMER ON

1. Push the On/Off switch on

base of unit to On – red light

will go on (A).

2. The unit will heat up in

approximately 100 seconds

and will be ready to use when

green light is on (B).

3. Push button on T-nozzle –

light will go on and steam

will start. Button on T-nozzle

can be used On or as a Pause

feature.

Always hold the nozzle about ½ inch from

fabric while steaming.

IMPORTANT SAFETY

INSTRUCTIONS

When using electrical appliances, espe-

cially when children are present, basic

safety precautions should always be taken,

including the following:

READ ALL INSTRUCTIONS

BEFORE USING

DANGER – Any appliance is electri-

cally live even when the switch is off.

To reduce the risk of death by electric shock:

1. Always unplug appliance immediately

after using.

2. Do not place or store appliance where it

can fall or be pulled into a tub or sink.

3. Do not place in, or drop into water or

other liquids.

4. If an appliance falls into water, unplug it

immediately. Do not reach into the water.

WARNING –

To reduce the risk of

burns,

electrocution, fire, or injury to persons:

1. This appliance should never be left

unattended when plugged in.

2. This appliance should not be used by, on,

or near children or individuals with certain

disabilities. Unsupervised use could result in

fire or personal injury.

3. Use this appliance only for its intended

use as described in this manual. Do not

use attachments not recommended by the

manufacturer.

4. Never operate this appliance if it has a

damaged cord or plug, if it is not work-

ing properly, or if it has been dropped or

damaged, or dropped into water. Do not

attempt to repair the appliance. Incorrect

reassembly or repair could cause a risk

of fire, electric shock, or injury to persons

when the appliance is used. Return the

appliance to an authorized service center

for examination and repair.

5. Keep the cord away from heated surfaces.

Do not allow cord to touch heated surfaces.

Do not pull or twist cord. Let appliance cool

completely before putting away.

6. To reduce the risk of electric shock, this

appliance has a polarized plug (one blade

is wider than the other). This plug will fit in

a polarized outlet only one way. If the plug

does not fit fully in the outlet, reverse the

plug. If it still does not fit, contact a qualified

electrician to install the proper outlet. Do not

change the plug in any way.

7. Never drop or insert any object into any

opening or hose.

8. Do not use outdoors or operate where

aerosol (spray) products are being used or

where oxygen is being administered.

9. Do not use an extension cord to operate

appliance.

10. Surfaces of this appliance may be hot

when in use. Do not let heated surfaces

touch eyes or skin.

11. Do not place the steam nozzle directly on

any surface or on the appliance power cord

while it is hot or plugged in. Use the stand

provided.

12. Unplug this appliance before filling or

emptying. Do not overfill.

13. While emitting steam, this appliance may

cause burns if it is used too close to the skin,

scalp or eyes, or if it is used incorrectly. To

reduce the risk of contact with hot water

discharging from steam vents, test appliance

before each use by holding it away from body.

14. Do not operate steamer without properly

filling the water tank.

15. Always keep the hose and nozzle

elevated above the water tank.

16. Never yank cord to disconnect from

outlet. Instead, grasp plug and pull to

disconnect.

17. Burns could occur from touching hot

metal parts, hot water, or steam. Use care

when removing water tank or when you turn

a steam appliance upside down – there may

be hot water in reservoir.

18. To reduce likelihood of circuit overload,

do not operate another high-wattage appli-

ance on the same circuit.

19. If an extension cord is absolutely

necessary, a 15 ampere rated cord should

be used. Cords rated for less amperage may

overheat. Care should be taken to arrange

the cord so that it cannot be pulled or

tripped over.

20. Always remove the water tank from the

appliance before filling it with water.

21. When changing attachments, please be

sure the unit is off and no steam is being

released in order to avoid contact with hot

water.

22. Use caution when changing attachments,

as there may be hot water from condensation.

Ensure the attachments are dry or cooled off,

to avoid contact with hot water.

SAVE THESE

INSTRUCTIONS

FOR HOUSEHOLD USE ONLY

UNPACKING INSTRUCTIONS

Place the box on a large, sturdy flat surface.

Carefully remove the appliance from the

packing material. Keep all plastic bags away

from children.

STEAMER ASSEMBLY

Attaching the Telescopic Pole and

Rotating Hanger

1. Turn the lock on top of base unit to unlock

position and place telescopic pole into open-

ing. Turn clockwise to lock.

2. Fully extend the telescopic pole, making

sure to lock the pole upright by engaging

the two clips, and hang the steam nozzle

from the cradle atop the 360 degree rotating

hanger assembly.

3. Pull lower pants clips towards you and

rotate clockwise to lock into place.

4. This unit comes with a rotating hanger. To

use the hanger, simply place on top of pole

firmly. Then tighten lower nut to keep hanger

upright or untighten to collapse hanger. It

is now in place to rotate 360˚. Hang your

garment and steam away wrinkles. Turn as

you wish.

5. Attach the top pants clip bar to the rotat-

ing hanger by inserting mounting pegs into

the hanger’s two keyhole openings. Push in

and pull down to lock. See instruction

booklet "Using pant clip system", Fig.3

for more details.

OPERATING

INSTRUCTIONS

FILLING THE WATER TANK

(PRIOR TO PLUGGING IN THE APPLIANCE)

Remove the water tank using

handle on front of tank. Fill

reservoir using opening on top

of tank by holding it under a

source of cold running water

until it is filled to the desired

level. Do not overfill. Position the water tank

on the base and make certain it is seated

properly in the unit.

DO NOT FILL THE TANK WITH HOT WATER.

DISTILLED OR FILTERED WATER IS BEST.

Do not unscrew the bottom

cap unless for cleaning (Fig. 4).

Note, be sure always empty or

fill the tank over a sink, being

careful not to spill water from

the top of the tank.

GET TO KNOW YOUR STEAMER USING PANT CLIP SYSTEM

This fabric steamer is equipped with a pant

clip system for holding pants taut for faster

and more effective steaming.

Attach the top pants clip bar to the rotating

hanger by inserting mounting pegs into the

hanger’s two keyhole openings (Fig. 3).

Push in and pull down to

lock (as highlighted above).

The bottom clips can be

adjusted by loosening the

knob (on the telescopic

pole) and moving the pole

up and down, depending

upon the length of pants.

Clip pants as shown and

steam. Please note: some

pants may be too long to

use the bottom clips. If

that is the case, just sim-

ply use the top clips and

let your pants hang freely.

cool-touch

insulated hose

360˚ rotating,

collapsible

hanger

Clips for

steaming

pants

Main On/Off

switch

(red light)

Ready to use

indicator light

(green light)

T-nozzle On/Off

button for steam

Telescoping

pole for height

adjustment

TOP

Steam nozzle with

aluminum faceplate

Removable,

easy-to-fill

large capacity

water tank

2 large

diameter

casters

(Fig. 1)

(Fig. 2)

(Fig. 3)

BOTTOM

(Fig. 4)

Bristle brush attachment

Creaser Attachment

ATTACHMENTS

The bristle brush attachment easily snaps

over the T-nozzle as shown below (Fig. 5).

For the creaser attachment, simply line up at

base and slide into back under T-nozzle and

push firmly to attach as shown below (Fig. 6).

Make sure your steamer is off and has cooled

before adding or removing attachments.

(Fig. 5)

(Fig. 6)

gs95_13pa140688_ib_final.indd 1 3/1/13 3:11 PM

TROUBLESHOOTING THE STEAMER

• PROBLEM - Steamer fails to heat

CAUSE - Steamer not plugged in

SOLUTION - Plug into electrical outlet

• PROBLEM - No steam

CAUSE - Water level is low (beep will sound)

SOLUTION - Turn On/Off switch off

and refill water tank

• PROBLEM - Water drips from nozzle

CAUSE - Condensation in hose

SOLUTION - Hold the hose vertically

and allow water to drain back into unit

• PROBLEM - Nozzle gurgles

CAUSE - Condensation in hose

SOLUTION - Hold the hose vertically

and allow water to drain back into unit

• PROBLEM - Poor steam performance

CAUSE - Sediment in tank

SOLUTION - Decalcify reservoir and

water tank. See decalcification instructions.

• PROBLEM - Dye on T-nozzle

CAUSE - Fabric not colorfast / Touching

T-nozzle to fabric

SOLUTION - Move T-nozzle 1/2 inch away

from fabric during use. Clean T-nozzle

with household cleaner and rinse with soap

and water

• PROBLEM - Discoloring of fabric

CAUSE - Dye on surface of fabric needs

specialty treatment and cleaning / Fabric

not suitable for steaming

SOLUTION - Some custom specialty fabrics

have dyes that are NOT COLORFAST and

are not suitable for steaming. Test fabric

for colorfastness in an inconspicuous spot

before steaming.

LIMITED ONE-YEAR WARRANTY

Conair will repair or replace (at our option)

your unit free of charge for 12 months from

the date of purchase if the appliance is

defective in workmanship or materials.

To obtain service under this warranty,

return the defective product to the service

center listed, together with your purchase

receipt and $3.00 for postage and handling.

California residents need only provide proof

of purchase and should call 1-800-366-0937

for shipping instructions. In the absence of a

purchase receipt, the warranty period shall

be 12 months from the date of manufacture.

ANY IMPLIED WARRANTIES, INCLUDING

BUT NOT LIMITED TO THE IMPLIED

WARRANTY OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE,

SHALL BE LIMITED IN DURATION TO THE

12-MONTH DURATION OF THIS WRITTEN,

LIMITED WARRANTY. Some states do not

allow limitations on how long an implied

warranty lasts, so the above limitations may

not apply to you.

IN NO EVENT SHALL CONAIR BE LIABLE

FOR ANY SPECIAL, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES FOR BREACH

OF THIS OR ANY OTHER WARRANTY,

EXPRESS OR IMPLIED, WHATSOEVER.

Some states do not allow the exclusion or

limitation of special, incidental, or conse-

quential damages, so the above limitation

may not apply to you.

This warranty gives you specific legal rights,

and you may also have other rights, which

vary from state to state.

CLEANING AND STORING

1. Turn the On/Off switch to the Off position

and unplug from the power source.

2. Wait for the steamer to cool completely for

at least 30 minutes.

3. Remove the water tank from unit, open

bottom cover and empty unused contents.

Allow to air dry.

4. Collapse telescopic hanger pole.

5. Replace water tank.

6. Store the unit.

DECALCIFICATION

If the appliance begins to produce steam

more slowly than usual or stops producing

steam and then starts again, you may need to

decalcify your steamer. Decalcification refers

to removing the calcium deposits that form

over time on the metal parts of the steamer.

For best performance from the Conair

Extreme Steam™ Fabric Steamer, decal-

cify the unit once a month. The frequency

depends upon the hardness of your tap water

and how often you use the steamer.

To decalcify, add a solution of 1/3 white vin-

egar and 2/3 water in the water tank. Place

the water tank in the unit. Plug the unit into

electrical outlet. Turn to the On position and

run until half the amount has steamed (1

liter). Turn the unit to the Off position, unplug

from electrical outlet, and allow to sit for

30 minutes.

Repeat the above procedure as many

times as necessary until a normal steam

rate returns, usually 2–3 times. With each

repeated cycle, use a fresh solution of vin-

egar and water. Run one cycle of fresh, cold

water without vinegar through the unit at the

completion of decalcification before using

the unit again to steam garments.

HOW TO STEAM

Grasp the handle of the steam nozzle with

the steam jets facing away from you. Begin

at the bottom of the fabric to allow the

steam to rise inside and outside, removing

wrinkles. Slowly move the nozzle from the

bottom to the top of the fabric. Remove the

nozzle from the garment and smooth the

fabric with your free hand. Some fabrics are

best steamed on the underside of the mate-

rial. This will allow the fibers of the fabric to

relax, eliminating wrinkles.

NOTE: Test fabric for color fastness in an

inconspicuous spot. Drape linens, towels,

handkerchiefs and napkins over a rod or

place on a towel rack.

Heavier fabrics may require repeated steam-

ing. Repeat as necessary.

With practice, you will gain speed and

efficiency. You will soon learn which

fabrics require multiple steam applications.

Do not directly touch velvet or silk with the

steam head.

Always steam with hose in upright

position, so any condensation is free

to flow back into the steamer. Always

hold the nozzle about ½ inch from fabric

while steaming.

If you steam in a low position, condensation

will collect inside the hose. This will cause

gurgling and some water droplets to form

near the steam jets on the handle. To avoid

this, frequently lift the steam handle upward

until the hose is extended to its full height.

TO STEAM DRAPES

Wash and dry drapes as directed, according

to fabric type. Rehang drapes and steam

when they are in place.

Please register this product at:

www.conair.com/registration

Service Center

Conair Corporation

Service Department

7475 N. Glen Harbor Blvd.

Glendale, AZ 85307

For information on any Conair product call:

1-800-3-CONAIR or visit us on the web at

www.conair.com

East Windsor, NJ 08520/Glendale, AZ 85307

13PA140688

CAUTION: Hose will be hot when

in use. Avoid prolonged contact.

IB-12095

Instructions

for Use

For your safety

and continued

enjoyment of this

product, always

read the instruction

book carefully

before using.

Model GS95

D U A L H E A T

withwith

™

ons

ety

this

ays

ruction

U A L H E A T

NOTE: Amounts of chemicals in water will

vary in different areas. To ensure contin-

ued operation of the steamer, never store

without cleaning and removing excess

water from the reservoir and water tank.

FABRIC STEAMER

gs95_13pa140688_ib_final.indd 2 3/1/13 3:11 PM

Product specificaties

Merk:	Conair
Categorie:	Stoomreiniger
Model:	GS95
Kleur van het product:	Grey, White
Vermogen:	1500 W
Capaciteit watertank:	1.8 l
Soort apparaat:	Rechtopstaande kledingstomer
Opwarmtijd:	1.5 min