Code Corporation CodeXML M3 Handleiding

Code Corporation Netwerkkaart/adapter CodeXML M3

Lees hieronder de 📖 handleiding in het Nederlandse voor Code Corporation CodeXML M3 (2 pagina's) in de categorie Netwerkkaart/adapter. Deze handleiding was nuttig voor 57 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Connecting with QuickConnect Code

Scan the QuickConnect Code on the label of the CodeXML M3 Bluetooth® Modem using

the Code Reader with which you wish to establish a paired connection. The reader and

computer should connect within 10 seconds. The reader will beep once as conﬁ rmation,

the modem’s LED light will become solid once the connection is established. If the reader

does not connect, the reader will beep four times in rapid succession.

English (Default) Universal French German

CodeXML M3 Bluetooth® Modem Installation as a USB Keyboard

Figure 3

Cable Installation

Attach the end of the USB cable to the CodeXML M3 Bluetooth® Modem (Figure 2). Plug

the USB connector into the USB port on the computer (Figure 3). Once plugged in the

modem’s blue LED light will ﬂ ash.

Figure 2

Establish Mode

Establish connection (see above), then scan the USB Mode code

(M708_01). Scan the QuickConnect Code again. You are ready to begin

reading bar codes and transmitting data to the computer.

USB Cable installed to

CodeXML M3 Bluetooth® Modem

USB Mode

Non-printable ASCII

Keyboard (Crtl + character)

Japanese Non-printable ASCII Keyboard

(No Leading 0)

Keyboard Input (USB)

The modem is defaulted to English language keyboards. If you need to communicate in a

diﬀerent language requiring a change in keyboard settings, please scan the appropriate

code below, after connecting to the modem:

CodeXML M3 Blueooth® Modem Installation as a RS-232 (Serial)

Figure 4 Figure 5 Figure 6 Figure 7

Cable Installation

Attach the end of the RS-232 cable to the CodeXML M3 Bluetooth® Modem

(Figure 4). Connect the RS-232 adapter to the back of the computer (Figure 5).

Connect the RS-232 cable to the power supply (Figure 6). Plug the power supply into

a wall socket (Figure 7). Once connected the Modem’s blue LED light will turn on.

RS-232 Cable (Left), CodeXML M3

Bluetooth® Modem (Center), Power

Supply (Right)

Change Baud Rate Settings: Scan the appropriate code below, after connecting to

the modem:

Note: Codes only aﬀect Baud Rate for the modem and do not affect any settings on Code Readers.

9600 (Default) 19200 38400

57600 115200

Default Modem

settings:

Baud Rate: 9600

Stop Bits: 8

Parity: None

Stop Bits: 1

Hardware: None

Connecting with QuickConnect Code

See instructions on page 2 for establishing a Bluetooth connection between the modem

and the reader.

Establish Mode

Establish connection (see page 2), then scan the RS-

232 Mode code (M661_01). Scan the QuickConnect

Code again. You are ready to begin reading bar codes

and transmitting data to the computer.

RS-232 Mode

2 C003996_03_CodeXML_M3_Modem_Quickstart C003996_03_CodeXML_M3_Modem_Quickstart 3

Quickstart Guide

4 C003996_03_CodeXML_M3_Modem_Quickstart

CodeXML M3 Bluetooth® Modem -

Multiple Interface Unit (MIU)

C003996_03_CodeXML_M3_Modem_Quickstart 1

The CodeXML M3 Bluetooth® MIU Modem is an external PC accessory designed

to be connected to a computer for use with a Code Reader (CR2 or CR3). The

Modem enables a reader to wirelessly transmit data to the computer without

installing any software or drivers. The Modem can accommodate USB and RS-232

(Serial) cables (Figure 1).

Figure 1

The CodeXML M3 Bluetooth® Modem is ‘plug & play.’ You simply plug-in the Modem,

scan the QuickConnect code on the Modem label and start transmitting data from

Code Readers without downloading any drivers or software. The Modem can receive

Bluetooth signals from up to 300 feet (100 meters) away.

For assistance, contact Code Technical Support at: (801) 495 2200; or by email:

support@codecorp.com

CodeXML M3 Bluetooth® Modem

VVVVvvvvCKPE BaudString:

VVVV 4 digit ﬁ rmware version

vvvv Not Applicable to the CodeXML M3 Bluetooth Modem

C 1 digit comm mode: 1=RS-232, 2=Wand Emul., 3=USB

KBD

K Keyboard Map, same as reader host ICD setting 0x2d

P 1 digit packet protocol: 0=Raw, 1=SPX packet, 2=Code

Reader packet

E Pre-emptible Mode

1=enabled, 0=oﬀ/disabled

M Max Packet Sized (Firmware version 1080 and Higher)

1= enabled, 0=oﬀ/disabled

BaudString spx: Baud:DataBitsParityStopbits

For All Readers:

Scan to View

Firmware Version

Modem Firmware Version Output & Values (for reference only):

The CodeXML M3 Bluetooth® Modem has been tested for compliance with FCC and CE

regulations and was found to be compliant with all applicable FCC Rules and Regulations.

FCC ID#: QQ6-XML02

Model #: BTHDG-M3-RO-CX

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment oﬀ and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit diﬀerent from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV technician for help.

Any changes made by the user not approved by Code Corporation can void the user’s authority

to operate the equipment.

To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation of 20 cm

or more should be maintained between the antenna of this device and persons during device

operation. To ensure compliance, operations at closer than this distance are not recommended.

The antenna used for this transmitter must not be co-located in conjunction with any other

antenna or transmitter.

CodeXML M3 Bluetooth® Modem

Important Note:

US Patent: US 7,240,831, Patents Pending.

Product specificaties

Merk:	Code Corporation
Categorie:	Netwerkkaart/adapter
Model:	CodeXML M3
Kleur van het product:	Zwart
Breedte:	69.85 mm
Diepte:	81.28 mm
Hoogte:	25.4 mm
LED-indicatoren:	Ja
Bluetooth-versie:	2.0+EDR
Connectiviteitstechnologie:	Draadloos
Certificering:	CE, FCC
Interface:	Bluetooth
Duurzaamheidscertificaten:	RoHS
Plug and play:	Ja
Wifi-band:	Single-band (2.4 GHz)
Ondersteunt Windows:	Ja
Intern:	Nee
Stroomverbruik:	100 mA
Ondersteunt Linux:	Ja
Spanning:	5 V
Verbinding met pc:	Ja
Maximale overdrachtssnelheid van gegevens:	1 Mbit/s
Modemsnelheid:	115 Kbit/s
Maximale afstand:	10 m
Antenne:	Ja
Bedrijfstemperatuur (T-T):	0 - 70 °C
Spread spectrum methode:	FHSS