Clas Ohlson 30-7724 Handleiding

Clas Ohlson Niet gecategoriseerd 30-7724

Lees hieronder de 📖 handleiding in het Nederlandse voor Clas Ohlson 30-7724 (20 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 125 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/20

E N G L I S H S V E N S K A N O R S K S U O M I

Ver. 200710

www.clasohlson.com

30-7724

Please read the entire instruction manual before using and save it for future use.

Läs igenom hela bruksanvisningen före användning och spara den sedan för framtida bruk.

Les nøye igjennom hele bruksanvisningen og ta vare på den til senere bruk.

Lue käyttöohjeet ennen tuotteen käyttöönottoa.

SE

ModelJYQ2-9410

FloorJack

Domkraft

Donkraft/Jekk

Tunkki

E N G L I S H

FloorJack•30-7724

Please read the entire instruction manual before using and save it for future use. We apologise for

any text or photo errors and any changes of technical data. If you have any questions concerning

technical problems please contact our Customer Service Department (see address on reverse.)

NOTE!

• The oor jack is only intended for lifting. The vehicle must be secured with axle stands (or

similar) with enough load capacity before you start working underneath the load.

• Do not overload the oor jack. It can lift up to 2 tonnes. Overloading could damage the jack,

property or cause personal injury.

• Make sure that there are no animals or people under the load until the load is secured with

e.g. axle stands.

• The jack must not be used for lifting people or animals.

• Do not try to move the jack when it is under load.

• The jack must not be modied in any way.

• Use the lifting points recommended by the manufacturer of your car.

• The oor jack is intended for use on an even, hard surface. If used on other surfaces the oor

jack could become unstable and drop its load.

• Make sure that the load is centred on the lifting cup.

Use

Beforeuse

Bleeding

1. Insert the handle into the handle sleeve (no. 10 on the drawing).

2. Pump the handle 6 full strokes with the release valve open to make sure that the oil is evenly

distributed.

3. Shut the release valve. The bleeding is now completed.

Inspection

1. A visual inspection of the jack should be made each time the jack is used. Make sure that there

are no cracks in the welds or other parts, oil leaks, loose parts, deformed or worn parts etc.

Liftingloads

1. Place the oor jack on an even, hard surface.

2. Close the release valve by inserting the handle and turning it clockwise, do not turn it too hard.

3. Position the jack’s lifting cup at a suitable point under the load.

4. Make sure that no people or animals are under the load whilst it is being lifted.

5. Insert the handle into the handle sleeve and pump the handle a few times to make sure that

the load is securely seated on the lifting cup, continue lifting the load to the desired height.

Secure the load by slowly lowering it onto supports such as axle stands.

E N G L I S H

Loweringloads

1. Close the release valve by inserting the handle and turning it clockwise, do not turn it too hard.

2. Make sure that no people or animals are under the load whilst it is being lowered.

3. Pump the handle, raising the load enough for the axle stands to be removed.

4. Using the handle, turn the release valve carefully anticlockwise, allowing the load to lower

slowly until it is completely down.

Care

1. When the jack is not in use the lifting arm and handle sleeve should be in the fully lowered

position. This prevents the pistons from rusting.

2. The oil container holds approx. 0.5 l hydraulic oil.

3. Keep the oor jack clean and well lubricated, even the moveable parts on the outside e.g. the

lifting arm spindle and wheel bearings.

Problems:Localisationandsolution

1. Thefloorjackdoesnotgoupordoesn’tlifttheload

a) The release valve is open, close the release valve and then try lifting.

b) There might be air pockets in the oil system. Open the release valve. Pump the handle six full

strokes. Close the release valve and try again.

c) Check the oil level. Do the following: Put the oor jack on an even surface. Open the release

valve. The oil level is correct if there is oil up to the lower thread inside the oil container when

the lifting arm is in the fully lowered position. If the oil level is too low you need to remove the

plug under the cover plate and ll the oil to the right level, then put the plug back and tighten

it. Shut the release valve and raise the lifting arm to its full height. Open the release valve

to lower the lifting arm. Do this 3 or 4 times. The air should now be purged and the oil can

circulate everywhere. In most cases that is enough to get the oor jack to work properly. Close

the release valve and try lifting a load.

d) The release valve is not tight because of dirt on the seal. Rinse by pulling the lifting arm up

and down several times with the release valve open. If it is necessary you can remove the

valve for cleaning.

2. Thefloorjacksinkswhenloaded

a) The piston o-ring could be worn out. This is only likely if the oor jack has been used long and

hard. Contact our Customer Service Department.

b) Dirt in the release valve makes the oor jack sink while under load. Remove the release valve,

clean the seat and replace the valve.

3. Thefloorjackdoesnotsinkcompletelyafterlifting

a) The lifting arm return spring is loose or has broken off. Replace it.

b) The oor jack probably needs to be lubricated. Clean and lubricate all movable parts in the

lifting mechanism.

Product specificaties

Merk:	Clas Ohlson
Categorie:	Niet gecategoriseerd
Model:	30-7724

Heb je hulp nodig?

Als je hulp nodig hebt met Clas Ohlson 30-7724 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Clas Ohlson

Clas Ohlson 30-7724 Handleiding

19 Juni 2023

Clas Ohlson SY-M30W Handleiding

8 Mei 2023

Clas Ohlson 41-2494 Handleiding

22 April 2023

Clas Ohlson EFP700ET Handleiding

19 April 2023

Clas Ohlson KG9000 Handleiding

18 April 2023

Clas Ohlson 9311 Handleiding

16 April 2023

Clas Ohlson 40-7275 Handleiding

8 April 2023

Clas Ohlson 7G1H Handleiding

26 Maart 2023

Clas Ohlson WK-0807 Handleiding

24 Maart 2023

Clas Ohlson OY-340-5A Handleiding

23 Maart 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Smeg GTA-6 Handleiding

21 November 2024

Smeg KIT6CX Handleiding

21 November 2024

Senal SCS-98 Handleiding

21 November 2024

Senal ASM-6 Handleiding

21 November 2024

Senal ASM-MNTKIT Handleiding

21 November 2024

Senal SMS-45 Handleiding

21 November 2024

Smeg KIT6PX Handleiding

21 November 2024

Senal SCI-3212MP Handleiding

21 November 2024

Matterport Pro2 3D Camera MC250 Handleiding

21 November 2024

Senal OLM-2S-P Handleiding

21 November 2024