Cisco UCS B200 M3 Handleiding

Cisco Server UCS B200 M3

Lees hieronder de 📖 handleiding in het Nederlandse voor Cisco UCS B200 M3 (36 pagina's) in de categorie Server. Deze handleiding was nuttig voor 49 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/36

Americas Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Cisco UCS B200 M3 Blade Server Installation and

Service Note

The Cisco UCS B200 M3 (shown in Figure 1) is the latest Cisco Intel-based, half-width blade supporting

two CPU sockets using Intel E5-2600 series CPUs and up to 24 DIMMs; it supports one modular LOM

(dedicated slot for Cisco's Virtual Interface Card) and one adapter card. At this time, the UCS B200 M2

(second generation) server is still available and is documented elsewhere. You can install up to eight

UCS B200 Blade Servers to a UCS chassis, mixing with other models or Cisco UCS blade servers in the

chassis if desired. The Cisco UCS B200 M3 is managed by Cisco UCS Manager version 2.0(2m) and

later.

Figure 1 Cisco UCS B200 M3 Front Panel

1 Asset tag 1

1.Each server has a blank plastic tag that pulls out of the front panel which is provided so that you can add your own

asset tracking label without interfering with the intended air flow.

7 Network link status LED

2 Blade ejector handle 8Blade health LED

3 Ejector captive screw 9Console connector

4 Hard drive bay 1 10 Reset button access

5 Hard drive bay 2 11 Beaconing LED and button

6 Power button and LED

UCS B200 M3

1 2 3 6 78 9 10 11

331360

Cisco UCS B200 M3 Blade Server Installation and Service Note

OL-26624-01

LEDs

Server LEDs indicate whether the blade server is in active or standby mode, the status of the network

link, the over all health of the blade server, and whether the server is set to give a flashing blue beaconing

indication. See Table 1 for details.

The removable hard disks also have LEDs indicating hard disk access activity and hard disk health.

Buttons

The Reset button is just inside the chassis and must be pressed using the tip of a paper clip or a similar

item. Hold the button down for five seconds, and then release it to restart the server if other methods of

restarting are not working.

Table 1 Blade Server LEDs

LED Color Description

Power Off Power off.

Green Normal operation.

Amber Standby.

Link Off None of the network links are up.

Green At least one network link is up.

Health Off Power off.

Green Normal operation.

Amber Minor error.

Blinking

Amber

Critical error.

Beaconing Off Beaconing not enabled.

Blinking

blue 1 Hz

Beaconing to locate a selected blade—If the LED is not

blinking, the blade is not selected. You can initiate

beaconing in UCS Manager or with the button.

Activity

(Disk Drive)

Off Inactive.

Green Outstanding I/O to disk drive.

Flashing

Amber

4 Hz

Rebuild in progress. Health LED will flash in unison.

Flashing

Amber

4 hz

Identify drive active.

Health

(Disk Drive)

Off Can mean either no fault detected or the drive is not

installed.

Flashing

Amber

4 hz

Identify drive active. If the Activity LED is also flashing

amber, a drive rebuild is in progress.

Amber Fault detected.

Cisco UCS B200 M3 Blade Server Installation and Service Note

OL-26624-01

The beaconing function for an individual server may get turned on or off by pressing the combination

button and LED. See Table 1 for details.

The power button and LED allows you to manually take a server temporarily out of service but leave it

in a state where it can be restarted quickly. If the desired power state for a service profile associated with

a blade server or an integrated rack-mount server is set to "off", using the power button or Cisco UCS

Manager to reset the server will cause the desired power state of the server to become out of sync with

the actual power state and the server may unexpected shutdown at a later time. To safely reboot a server

from a power-down state, use the Boot Server action in Cisco UCS Manager.

Connectors

The console port allows a direct connection to a blade server to allow operating system installation and

other management tasks to be done directly rather than remotely. The port uses the KVM dongle cable

(N20-BKVM shown in Figure 2) which provides a connection into a Cisco UCS blade server; it has a a

DB9 serial connector, a VGA connector for a monitor, and dual USB ports for a keyboard and mouse.

With this cable, you can create a direct connection to the operating system and the BIOS running on a

blade server. A KVM cable sh ade chassis accessory kit.ips standard with each bl

Figure 2 KVM Cable for Blade Servers

Conventions

This document uses the following conventions for notes, cautions, and safety warnings.

Notes and Cautions contain important information that you should know.

Note Means reader take note. Notes contain helpful suggestions or references to material that are not covered

in the publication.

Caution Means reader be careful. You are capable of doing something that might result in equipment damage or

loss of data.

1 3Connector to blade server slot VGA connection for a monitor

2 4DB9 serial connector 2-port USB connector for a mouse and keyboard

192621

Product specificaties

Merk:	Cisco
Categorie:	Server
Model:	UCS B200 M3
Kleur van het product:	Zilver
Gewicht:	4360 g
Breedte:	203 mm
Diepte:	620 mm
Hoogte:	50 mm
Processorfamilie:	Intel
Temperatuur bij opslag:	-40 - 65 °C
Processor socket:	LGA 2011 (Socket R)
Systeembus:	8 GT/s
Maximum intern geheugen:	768 GB
On-board graphics adapter model:	Matrox G200
Luchtvochtigheid bij opslag:	5 - 93 procent
ECC:	Ja
Geheugen form factor:	240-pin DIMM
Chipset moederbord:	Intel C600
Ondersteunde opslagstationinterfaces:	Serial Attached SCSI (SAS),Serial ATA III
Soorten RAID:	0,1
Compatibele processors:	Intel® Xeon®
Aantal ondersteunde processoren:	2
Intel® Xeon series:	E5-2600
Aantal DIMM sloten:	24
Aantal storage drives ondersteund:	2
Opslagschijf afmetingen ondersteund:	2.5 "
Ondersteunde geheugen types:	DDR3-SDRAM
Hot-swap HDD bays:	Ja
Bedrijfstemperatuur (T-T):	10 - 35 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 93 procent
Code geharmoniseerd systeem (HS):	84714100