CicloSport HAC 5 Handleiding

CicloSport Hartslagmeter HAC 5

Lees hieronder de 📖 handleiding in het Nederlandse voor CicloSport HAC 5 (4 pagina's) in de categorie Hartslagmeter. Deze handleiding was nuttig voor 34 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

ATTENTION! To save energy, the 5 turns off automatically at night, meaning the dis-HAC

play turns off at 12 p.m. and only lights up again after pressing any button.

All functions active at the time of shut-off keep going internally despite the display tur-

ned down.

Operational Setup

2.1 Attaching the HAC5 to the wrist band and the handlebar bracket

To take the HAC5 out of the wrist band or the handlebar holder, turn it 90° to the left, then re-

move.

To insert into the wrist band or handlebar bracket, insert at a 90° angle to the left, then turn to

right until it engages.

Inserting the batteries

• Inserting the battery into the HAC5:

Open the battery cap on the back of the HAC5with the aid of a coin

(turn counter clockwise). Insert battery type CR2032 with plus pole fa-

cing up, please make sure that the battery is inserted at a angle from

the side (from right to left), so that the contacts lie on the battery. Then

close the battery cap. The display of the shortly shows all seg-HAC5

ments, then returns to the normal display.

• Inserting the battery into transmitter belt, speed- and cadence transmitter:

Open the battery cap with the aid of a coin (turn to left). Insert battery type CR2032 with the

plus pole facing up and close the cap again.

Setup / Initialization

Because of the new digital transmission technique, all transmitters have to be initialized prior to

first use. We therefore recommend that you first conduct all necessary initializations (and, if re-

quired, enter all required data) before attaching the parts to the bike. On page 3 (examples)

you will find a step-by-step setup as well for the initializations as for setup of time and date.

Installing

• Installing the handlebar bracket:

The handlebar mounting can also be installed on a stem. To do this the

top section of the handlebar mounting must be removed from the bot-

tom section. To make it easier to remove the top section carefully push

the sides of the bottom section upwards slightly.

Then turn both parts through 90° and assemble them

again until the snap-on mounting engages.

Remove the backing foil from the underside of the

handlebar mounting, place the handlebar mounting in

the required position on the handlebar (or on the stem)

and press it down slightly. Secure it with the O ring or

with the cable ties

“First steps” with the

handlebar

bracket

HAC5 Anl. 125x250 engl 25.07.2006 15:41 Uhr Seite 1

• Installing the speed transmitter:

Attach the speed transmitter at the fork or the rear construction

with the aid of the cable ties (the printed side of the transmitter

with the marking must point to the spokes).

Mount the magnet to a spoke directly opposite the marking on

the transmitter.

Do not over tighten the fixing screw on the magnet. Adjust transmitter in such a way that the

distance between transmitter and magnet does not exceed 3 millimetres.

• Installing the cadence transmitter:

Attach the cadence transmitter to a strut opposite the pedal crank with

the aid of the cable ties (the printed side of the transmitter with the mar-

king must point to the crank).

Mount the magnet on the pedal crank directly opposite the transmitter

with the help of the cable tie, so that the magnet points exactly to the

marking on the transmitter. Adjust transmitter in such a way that the

distance between transmitter and magnet does not exceed 3 millimetres.

Putting on the breast belt

Hang the transmitter belt in the elastic breast belt and then put the breast belt

around your (naked) upper torso. The transmitter (plastic part with inscription)

should be placed above the middle of your upper stomach region, slightly be-

low the breast and the inscription on the transmitter (when seen from the front)

must be legible (pictured).

Pacemaker wearers should consult their doctor before using any heart rate measuring

device!

If your skin is too cold or too dry, the electrical contact between the skin and the electrodes can

be so minimal that an accurate measurement is not possible. It often helps to wet the electrodes

and the skin where they are to be attached with your finger (do not wet the transmitter but only

the rubber parts on the left and on the right). If this doesn’t help, one should train until they start

sweating. You will get the best contact by means of a special electrode-gel (available at your lo-

cal pharmacy).

Using the buttons

The display of the HAC5is separated into 3 areas: an upper, a and a middle lower. Each

area displays one function, so that there are three functions displayed simultaneously at all

times. This means that the possible functions can be combined to personal taste.

The buttons are termed as follows in the manual:

U Lpper eft button: UL-button

U M UMpper iddle button: -button

U Rpper ight button: -buttonUR

M Riddle ight button: -buttonMR

L Lower eft button: LL-button

L Rower ight button: LR-button

The following applies:

The buttons on the right side main functionsaccess the

(UR-, MR- and LR-buttons).

The sub-functions of the functions in the upper and lower display are accessed through the

depending button on the left side (UL- and LL-buttons).

The stopwatch and the countdown are started, stopped and paused by shortly pressing the

UM-button and reset by pressing the -button for three seconds (this also deletes all split-UM

and lap times).

Every press of the button makes a short sound, this sound can be turned off in the advanced

settings.

Transmitter search – digital system

In order for the HAC5to display speed or heart rate or similar, the according transmitter has to

be found first.

The search begins automatically when a recording is started ( - and UL LL-buttons pressed si-

multaneously for three seconds), and manually by pressing the LL-button for three seconds (in

both cases, the active profile is shown for 10 seconds).

During this display all transmitters are searched for which are active in this profile. Should no or

not all transmitters be found during this time, then this is displayed when selected, for example:

➔

Mark

Electrodes

Transmitter

HAC5 Anl. 125x250 engl 25.07.2006 15:41 Uhr Seite 2

SPD: no TX, meaning that for the speed (= spd) display there were no transmitters (= tx) found.

In this case, the transmitter search must be started again (by pressing the LL button for three

seconds).

If the display shows “Speed Bike2”, for example, this means that the speed transmitter for bike 2

is activated (for example by turning the wheel) and was found.

Examples

Through the selection process, the settings of the HAC5are relatively easy to do (as most

displays are self-explaining). Thus we are showing you two short examples:

First settings (for example time, date)

- Press MR-button three seconds to enter the main setting mode.

By pressing shortly the -button a few times in a row choose the mode “basic set” LR-/UR

(= basic settings, appears in the dark area on the middle display),

- confirm by shortly pressing the -button.MR

- Select “set time” with the LR-/UR-button,

- confirm with the MR-button.

- Select “set clock” with the LR-/UR-button,

- confirm with the MR-button.

The current time is now flashing on the upper display, the lower shows the second time zone.

- The time can be set with the LR-/UR-button,

- confirm with the MR-button.

- After this the time (only the hours can be adjusted) of the second time zone flashes on the

lower display and can be set with the -button.LR-/UR

- Confirm with MR-button, “set clock” appears again on the display.

- Select “set date” with the LR-/UR-button,

- confirm with the MR-button.

- The year flashes on the upper display and can be adjusted with the -button, LR-/UR

- confirm with the MR-button, now the month flashes on the lower display.

- Also set with -buttons and confirm with -button.LR-/UR MR

Now the day flashes.

- Set to the right number with the LR-/UR-button and

- confirm with the MR-button.

- Select “back” with the LR-button and

- confirm with the MR-button to get back to the mode “basic settings”.

Now you can make further personal adjustments, like:

“Set altitude”: here the current altitude/air pressure can be set.

“Set units”: here the measuring units – kilometres or miles for distance, mbar or inhg for air

pressure etc. – can be determined.

“Set perso.”: this is where the personal data like date of birth, weight, sex, heart frequency-

limits and countdowns are entered, the

CICLO

nZone®can also be calculated and totals for

burning calories and burning fat determined.

“Set totals.”: here, total sums (like total kilometres, total time of tour etc.) can be preset or

erased for the current profile.

By pressing the -button for three seconds, the setting mode can be left at any time.MR

Initializing the transmitters

In order for the to be able to show heart rate, speed and cadence, the concerning trans-HAC5

mitters have to be initialized first.

Please do as follows:

Put on the transmitter belt:

- Press the MR-button for thr

ee seconds

- Select “Prof.Bike” with the LR-button (the selected line has a dark background)

- confirm with the MR-button

- The display shows “select bike“,

- confirm with MR-button

HAC5 Anl. 125x250 engl 25.07.2006 15:41 Uhr Seite 3

Product specificaties

Merk:	CicloSport
Categorie:	Hartslagmeter
Model:	HAC 5

Heb je hulp nodig?

Als je hulp nodig hebt met CicloSport HAC 5 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Hartslagmeter CicloSport

CicloSport HAC 4000 Handleiding

13 Juni 2023

CicloSport HAC 5 Handleiding

26 Mei 2023

Handleiding Hartslagmeter

Nieuwste handleidingen voor Hartslagmeter

Timex T5K738 Handleiding

25 Mei 2024

Rossmax SB220 Handleiding

27 Maart 2024

Beurer PO30 Handleiding

20 Februari 2024

Lanaform PO-110 Handleiding

9 Januari 2024

Ciclo HAC 5 Handleiding

30 Oktober 2023

Ciclo HAC 4000 Handleiding

30 Oktober 2023

Oregon Scientific AH300E Talking Heart Rate Monitor Handleiding

16 Oktober 2023

Oregon Scientific AH300 Talking Heart Rate Monitor Handleiding

16 Oktober 2023

Oregon Scientific AH300A Talking Heart Rate Monitor Handleiding

16 Oktober 2023

Oregon Scientific AH310E Handleiding

16 Oktober 2023