Chief PLP2000B Handleiding

Chief Flat panel steun PLP2000B

Lees hieronder de 📖 handleiding in het Nederlandse voor Chief PLP2000B (8 pagina's) in de categorie Flat panel steun. Deze handleiding was nuttig voor 40 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

CHIEF MANUFACTURING INC. 8805-000183 Rev F

8401 EAGLE CREEK PARKWAY, STE. 700 www.chiefmfg.com

SAVAGE, MINNESOTA 55378 USA 03/08

I N S T A LL A T I O N IN S T R U C T IO N S

PLP Series Wall Mount

The PLP Series wall mount accommodates large flat

screens weighing up to 200 lbs (90.72kg). The teardrop

holes in the mount allow for quick connect/disconnect of

the screen, thus simplifying installation and maintenance

processes.

The top and bottom mounting brackets are adaptable to

supporting framework with wood studs that are 16” on

center or 24”on center.

The mount has integrated lateral shift, allowing for four

different mounting options. For dual wood studs 16” on

center, the lateral shift is + 4.5 inches. For dual wood

studs 24” on center, the lateral shift is + 0.5 inches.

The display can be pulled and tilted by hand into any

position in the zero-to-15 degree tilt range and remain

stationary.

The bottom of the mount pulls forward 4” from the wall

and locks into place for installation of cable connections.

The mount also uses Chief’s exclusive Q-Latch™

mounting system, which offers quick connect/disconnect

display mounting. The display is secured to the mount

with a latching flag. For additional security, you can lock

the latching flag in place by adding a padlock. PLP Series

Installation Instructions PLP Series

! IMPORTANT: If the installation of this product requires OSHPD seismic approval, refer to OSHPD pre-approval

documents and drawings before beginning installation. OSHPD documents and drawings are available at

www.chiefmfg.com, and located on the product information page for the mount.

BEFORE YOU BEGIN

CAUTION: To prevent damage to your monitor and PLP, which could aﬀect or void the Factory

warranty, thoroughly study all instructions and illustrations before you begin to install the mount. Pay

particular attention to the Warnings and Cautions in this document.

The mount is designed to be installed using wall studs or supporting framework. The fasteners used to anchor the

mount must be capable of supporting five times the total weight of the equipment.

The maximum weight to be installed on the PLP Series wall mount is 200 lbs (90.72kg).

If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480 or 952-582-

6480.

IMPORTANT WARNINGS and CAUTIONS!

WARNING A WARNING alerts you to the possibility of serious injury or death if you do not

follow the instructions.

CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do

not follow the corresponding instructions.

WARNING Improper installation can result in serious personal injury! Make sure that the

structural members can support a redundant weight factor five times the total weight

of the equipment. If not, reinforce the structure before installing the mount.

WARNING Be aware of the potential for personal injury or damage to the equipment if it is not

installed correctly. Consider the weight of the mount without the display.

WARNING The installer is responsible for verifying that the display to which the wall mount is

fastened will safely support the combined load of all attached components or other

equipment.

WARNING The combined weight of the display placed on the wall mount must not exceed 200 lbs

(90.72kg),the maximum support weight of the mount.

WARNING Watch for pinch points. Do not put your ﬁngers between movable parts.

WARNING Make sure the flag securing the display is completely lowered at all times except when

removing or installing the display. The flag must be all the way down when

installing/removing cables.

CAUTION Check the unit for shipping damage before you begin the installation.

Installation Instructions PLP Series

DIMENSIONAL

DRAWING

17.00

.69

1.87

4.24

15.51

18.38

13.19

16.00

24.00

5/16" x 1" SLOT

5/16" x 6" SLOT

5/16" x 1" SLOT

TOP MOUNTING BUTTON ON

PSB-XXXX DRAWING GOES HERE

26.00

1.83

FACE TILTS

15 DOWN

7 UP (FOR SERVICE)

NOTE: CUSTOM INTERFACE BRACKET

NOT SHOWN. THE CUSTOM INTERFACE

BRACKET NEEDED FOR YOUR DISPLAY

WILL ADD BETWEEN 1/2" AND 2" IN DEPTH

AND MAY AFFECT LOCATION OF DISPLAY

ON THE MOUNT.

SEE PSB-XXXX DRAWING ALSO.

Product specificaties

Merk:	Chief
Categorie:	Flat panel steun
Model:	PLP2000B
Kleur van het product:	Zwart
Breedte:	660 mm
Diepte:	46.5 mm
Hoogte:	467 mm
Materiaal behuizing:	Staal
Montagewijze:	Muur
Maximale gewichtscapaciteit:	90.7 kg
Certificering:	TUV Approved, UL Listed
Paneelmontage-interface:	- mm
Bereik kantelhoek:	0 - 15 °
Maximale schermgrootte:	71 "
Minimale schermgrootte:	42 "
Afstand tot de muur (min):	46.5 mm