Chief KTA1003B Handleiding

Chief Flat panel steun KTA1003B

Lees hieronder de 📖 handleiding in het Nederlandse voor Chief KTA1003B (6 pagina's) in de categorie Flat panel steun. Deze handleiding was nuttig voor 20 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/6
I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
Dual Array Pole Mount Accessory
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
KTA1003
KTA1003 Installation Instructions
2
DISCLAIMER
CSAV, Inc., and its affiliated corporations and subsidiaries
(collectively, "CSAV"), intend to make this manual accurate and
complete. However, CSAV makes no claim that the information
contained herein covers all details, conditions or variations, nor
does it provide for every possible contingency in connection
with the installation or use of this product. The information
contained in this document is subject to change without notice
or obligation of any kind. CSAV makes no representation of
warranty, expressed or implied, regarding the information
contained herein. CSAV assumes no responsibility for
accuracy, completeness or sufficiency of the information
contained in this document.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for the installation of this kit can result in serious personal
injury or damage to equipment! It is the installer’s
responsibility to make sure the structure to which this mount
is attached can support five times the combined weight of all
equipment.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! See the
installation instructions that came with the array onto which
this accessory is being installed for weight limits.
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations

Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations

Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster

Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale

Installation Instructions KTA1003
3
TOOLS REQUIRED FOR INSTALLATION AND PARTS
x1
I/M
.200" (Ø 5mm)
E (4)
(1/4")
B (1)
A (1)
C (1)
F (2)
(1/4-20 x 7/8")
G (2)
(1/4-20 x 3/4")
D (2)
(5/32")
(1/4-20)
ASSEMBLY and INSTALLATION
The following procedures assume an additional base and pole
have been purchased and are available. The procedures also
assume that no displays are mounted to the existing array.
The KTA1003 is used to allow the attachment of an additional
pole and base to an existing array or connecting two arrays
together. (See Figure 1)
Figure 1
1. Loosen four Button head cap screws securing existing pole
clamp to array.
2. Slide existing base towards left hand side of array
approximately halfway between middle and left hand Centris
cup.
NOTE: Steps 1 and two do not apply if two arrays are being
joined together.
3. Loosen and remove end lock retaining screw and set aside
for reuse. (See Figure 2)
4. Slide end lock out of array channel and set aside for reuse.
(See Figure 2)
NOTE: If two arrays are being joined together the end lock
retaining screw and end lock must be removed from
ends that are being joined, and the hardware will not be
reused.
Figure 2
5. Remove two cable management clips from array and set
aside for reuse. (See Figure 3)
Single
Array
Dual Arrays
Array
End Lock
Square Nut

Product specificaties

Merk: Chief
Categorie: Flat panel steun
Model: KTA1003B

Heb je hulp nodig?

Als je hulp nodig hebt met Chief KTA1003B stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Flat panel steun Chief

Chief

Chief TS218SU Handleiding

9 December 2024
Chief

Chief K1D120BXDL Handleiding

17 November 2024
Chief

Chief RPMA204 Handleiding

17 November 2024
Chief

Chief LCB1U Handleiding

17 November 2024
Chief

Chief RPA640 Handleiding

17 November 2024
Chief

Chief FSBI2TB Handleiding

17 November 2024
Chief

Chief XCB1U Handleiding

17 November 2024
Chief

Chief RSA213 Handleiding

17 November 2024
Chief

Chief RSMBU Handleiding

17 November 2024
Chief

Chief PFQUB Handleiding

27 Juni 2024

Handleiding Flat panel steun

Nieuwste handleidingen voor Flat panel steun

Akai

Akai 2342T Handleiding

1 Januari 2025
Techly

Techly ICA-TR14 Handleiding

24 December 2024
Techly

Techly ICA-LCD 2500 Handleiding

24 December 2024
Peerless-AV

Peerless-AV HPF665 Handleiding

18 December 2024
Alogic

Alogic Glide C32GMA2 Handleiding

18 December 2024
NeoMounts

NeoMounts FPMA-D750WHITE2 Handleiding

17 December 2024
NeoMounts

NeoMounts FPMA-D750SILVER Handleiding

17 December 2024
NeoMounts

NeoMounts FPMA-D750WHITE Handleiding

17 December 2024
NeoMounts

NeoMounts FPMA-D700DD Handleiding

17 December 2024
NeoMounts

NeoMounts FPMA-D700D6 Handleiding

17 December 2024