Chauvet Rogue Outcast 1M Beam Handleiding

Chauvet Lamp Rogue Outcast 1M Beam

Lees hieronder de 📖 handleiding in het Nederlandse voor Chauvet Rogue Outcast 1M Beam (16 pagina's) in de categorie Lamp. Deze handleiding was nuttig voor 16 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/16

English EN

Español ES

Français FR

Deutsch DE

Nederlands NL

Quick Reference Guide

Model ID: ROGUEOUTCAST1MBEAM

Scan the QR code to

access the product page,

warranty terms, and the

complete User Manual

QUICK REFERENCE GUIDE

Rogue Outcast 1M Beam QRG Rev. 1

Safety Notes

These Safety Notes include important information about installation, use, and maintenance of the

Rogue Outcast 1M Beam.

What is Included

AC Power

This product has an auto-ranging power supply that can work with an input voltage range of 100–240 VAC, 50/60 Hz.

AC Plug

• The luminaire is intended for professional use only.

• The luminaire should be positioned so that prolonged staring into the luminaire at a distance closer than

16.40 ft (5 m) is not expected.

• If the external flexible cable or cord of this luminaire is damaged, it shall be replaced by a special cord or cord

exclusively available from the manufacturer or its service agent.

• The light source contained in this luminaire shall only be replaced by the manufacturer or its service agent or

a similar qualified person.

• CAUTION:

• This product’s housing may be roduct in a location with adequate hot when operating. Mount this p

ventilation, at least 20 in (50 cm) from adjacent surfaces.

• When transferring the product from extreme temperature environments, (e.g., cold truck to warm humid

ballroom) condensation may form on the internal electronics of the product. To avoid causing a failure,

allow the product to fully acclimate to the surrounding environment before connecting it to power.

• Flashing light is known to trigger epileptic seizures. User must comply with local laws regarding notification

of strobe use.

• ALWAYS:

• Disconnect from power before cleaning the product or replacing the fuse.

• Replace the fuse with the same type and rating.

• Use a safety cable when mounting this product overhead.

• Connect this product to a grounded and protected circuit.

• DO NOT:

• Open this product. It contains no user-serviceable parts.

• Look at the light source when the product is on.

• Leave any flammable material within 20 cm of this product while operating or connected to power.

• Connect this product to a dimmer or rheostat.

• Operate this product if the housing, lenses, or cables appear damaged.

• Submerge this product (IP65). Regular outdoor operation is fine.

• Permanently install outdoors in locations with extreme environmental conditions. This includes, but is not

limited to:

• Locations where normal temperatures exceed the temperature ranges in this manual.

• Locations that are prone to flooding or being buried in snow.

• Other areas where t ct to extreme radiahe product will be subje tion or caustic substances.

• ONLY use the hanging/mounting bracket to carry this product.

• The maximum ambient temperature is 113 °F (45 °C). Do not operate this product at higher temperatures.

• The minimum startup temperature is -4°F (-20°C). Do not start the product at lower temperatures.

• The minimum ambient temperature is -14°F (-10°C). Do not operate the product at lower temperatures.

• To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely disconnect the

product from power via breaker or by unplugging it.

• In the event of a serious operating problem, stop using immediately.

• Rogue Outcast 1M Beam

• Seetronic Powerkon IP65 power cable

• Omega bracket with mounting hardware

• Quick Reference Guide

Connection Wire (U.S.) Wire (Europe) Screw Color

AC Live Black Brown Yellow/Brass

AC Neutral White Blue Silver

AC Ground Green/Yellow Green/Yellow Green

To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely

disconnect the product from power via breaker or by unplugging it.

Rogue Outcast 1M Beam QRG Rev. 1

QUICK REFERENCE GUIDE

FCC Statement of Compliance

This device complies with Part 15 Part B of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's

authority to operate the equipment.

Power Linking

It is possible to power link Rogue Outcast 1M Beam products. See the table below for the current draw at each voltage

and frequency:

Never exceed 12A on a single circuit. Power-linking cables can be purchased separately.

Mounting

Before mounting this product, read the Safety Notes. Use at least 2 mounting points per product. Make sure the mounting

clamps are capable of supporting the weight of the product. For our Chauvet line of mounting clamps, go to

http://trusst.com/productcategory/truss-clamps.

Mounting Diagram

Control Panel Description

100 V, 60 Hz 120 V, 60 Hz 208 V, 60 Hz 230 V, 50 Hz 240 V, 50 Hz

Current Draw 2.32 A 1.95 A 1.11 A .990 A .960 A

Button Function

<MENU> Exits from the current menu or function

<ENTER> Enables the currently displayed menu or sets the currently selected value into the selected function

<UP> Navigates upwards through the menu list or increases the numeric value when in a function

<DOWN> Navigates downwards through the menu list or decreases the numeric value when in a function

Omega bracket

Overhead mounting Surface mounting

Safety cable

Mounting clamp

Product specificaties

Merk:	Chauvet
Categorie:	Lamp
Model:	Rogue Outcast 1M Beam

Heb je hulp nodig?

Als je hulp nodig hebt met Chauvet Rogue Outcast 1M Beam stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Lamp Chauvet

Chauvet EVE E-160ZQ Handleiding

24 December 2024

Chauvet Intimidator Hybrid 251SR Handleiding

24 December 2024

Chauvet CoDot ILS Handleiding

24 December 2024

Chauvet WELL POD 2X6 Handleiding

17 December 2024

Chauvet Shocker P2 Handleiding

25 November 2024

Chauvet Rogue Outcast 1M Beam Handleiding

4 November 2024

Chauvet COLORado Solo Bar 6 Handleiding

4 November 2024

Chauvet COLORado Solo Bar 1 Handleiding

4 November 2024

Chauvet COLORado Solo Bar 4 Handleiding

4 November 2024

Chauvet COLORstrip Pix ILS Handleiding

2 November 2024

Handleiding Lamp

Nieuwste handleidingen voor Lamp

Physa PHY-TCS-01 Handleiding

23 December 2024

Olight Baton 4 Premium Edition Handleiding

22 December 2024

Genaray LF-RGB-65 Handleiding

20 December 2024

Nanlite Compac 40 Handleiding

18 December 2024

Nanlite Compac 40B Handleiding

18 December 2024

Nanlite FC-60B Handleiding

18 December 2024

Nanlite MixPad II 27C Handleiding

18 December 2024

Nanlite MixPad II 11C Handleiding

18 December 2024

Nanlite D672II Handleiding

18 December 2024

Nanlite 600DSA Handleiding

18 December 2024