Chamberlain WSLCEVC-P1 Handleiding

Chamberlain Niet gecategoriseerd WSLCEVC-P1

Lees hieronder de 📖 handleiding in het Nederlandse voor Chamberlain WSLCEVC-P1 (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/8
To prevent possible SERIOUS INJURY or DEATH from electrocution
or fire:
• Turn off power at the fuse box or circuit breaker BEFORE
proceeding.
• The light control is ONLY for indoor use.
• Installation and wiring MUST be in compliance with ALL local
electrical and building codes.
SPECIFICATIONS
Bulb Type:
..............
Compact fluorescent, incandescent, or LED
Max Load Rating:...................................300 Watts
Incandescent Lamp
.................................
300 Watts Compact Fluorescent Lamp (CFL)...................... 2.5 Amps
Voltage .............................................120 Vac
NOTE: The wall plate is
not provided.
OVERVIEW
MODES OF OPERATION
REMOTE CONTROL OPERATION:
Allows you to activate the Smart Light Switch
from a remote control.
NOTE: If your remote control is already
programmed to your garage door opener, choose
a different remote control button to program to
the Smart Light Switch.
SMARTPHONE OPERATION:
Allows you to activate the Smart Light Switch from
your smartphone or tablet, set schedules to switch
your lights on/off at customized times, and receive
notifications when your light remains on.
* Smartphone control requires a MyQ® Garage, Smart Garage Hub,
MyQ®Internet Gateway, or Wi-Fi® Garage Door Opener.
The Smart Light Switch can be programmed to the MyQ
® app*, to a Security+ 2.0® remote control, or to a MyQ® enabled garage door opener.
GARAGE DOOR OPENER OPERATION:
Allows you to synchronize the Smart Light Switch
with your garage door opener light bulbs. The
synchronization with the garage door opener lights
is disabled if you manually turn the light switch on.
The light switch must be OFF to synchronize the
garage door opener with the light switch.
Example: The garage door opener light bulbs are set to automatically turn
off after 4 ½ minutes, the Smart Light Switch will also turn off after 4 ½
minutes.
Switch
LED
NOTICE: To comply with FCC and/or Industry Canada (IC) rules, adjustment or modifications of this
transceiver are prohibited. THERE ARE NO USER SERVICEABLE PARTS.
This device complies with Part 15 of the FCC rules and IC RSS-210. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Learn Button
Cover
CARTON INVENTORY
Screws (2)
Smart Light Switch
Wire Nuts
1
(2)(1)
The Smart Light Switch offers a
convenient way to control the lights in
your home. It can be programmed to
be controlled from anywhere with your
smartphone and the Chamberlain
MyQ® App*. The Smart Light Switch
is also compatible with up to 8
Security+ 2.0® remote controls a OR
combination of up to 8 MyQ
® enabled
garage door openers. This product is
NOT recommended for control of
household appliances or fans. Not for
use with 3-way or 4-way switch
combinations.
SMART LIGHT SWITCH
MODELS WSLCEVC & WSLCEVC-P1
BEFORE YOU BEGIN:
This device REQUIRES a ground; if a ground is not available, contact a
qualified electrician. If you are not experienced and familiar with electrical
wiring and electrical codes, contact a qualified electrician. Some codes
require installation by a qualified electrician. Install in accordance with all
national and local codes. Ensure the existing switch and light is working
prior to installing the new switch.
1. Disconnect power at the circuit breaker or fuse box BEFORE
proceeding.
2. Remove the wall plate and set aside for re-assembly.
REMOVE OLD WALL SWITCH:
1. Remove switch from switch box.
2. During removal, identify or label the load and line wires.
NOTE: Typically a line wire is the incoming hot wire from the circuit
breaker. The load wire is the wire supplying power between the switch
and the light.
3. Keep all load wires separated from line wires.
INSTALL NEW SWITCH (Figure 1):
1. Identify the antenna routing (Figure 1).
2. Connect the wires (Figure 2). NOTE: If your wiring includes a neutral
wire this wire is not required, combine neutral wire(s) and cap with
wire nut (not provided).
• Green wire to ground.
Connect the green wire on the new switch to the exposed copper
ground, green wire, or to the ground connection within metal
switch box. NOTE: If ground doesn’t exist contact an electrician to
add a ground. This product will not function without a proper
ground.
• Red wire to load.
• Black wire to line.
3. Secure connections with a wire nut and wrap each wire nut with
electrical tape.
NOTE:
Turn all wire nuts clockwise, making sure the bare wires are
covered. Tug on each wire nut to make sure the connections are good.
4. Carefully pack the wiring back into switch box. Make sure the wires are
not pinched or strained. Make sure the antenna is hanging straight
down between the switch box and the drywall.
5. Fasten the Smart Light Switch to the switch box with the screws
(provided).
6. Fasten the wall plate securely over the switch box with the original
screws from the wall plate.
TEST
1. Turn on the power to circuit at fuse box or circuit breaker.
2. Test the light switch, manually press the light switch to ensure the
light is functional (Figure 3). If it is not functional, see
Troubleshooting.
INSTALLATION
Figure 3
Black Wire Line
Red Wire Load
Green Wire Ground
To prevent possible SERIOUS INJURY or DEATH from electrocution
or fire:
• Turn off power at the fuse box or circuit breaker BEFORE
proceeding.
• The light control is ONLY for indoor use.
• Installation and wiring MUST be in compliance with ALL local
electrical and building codes.
Switch
Box
Load
Light
Line
Circuit Breaker
or Fuse Box
Black
Wire
Red
Wire
Line
Wire
Neutral
Load
Wire
Load
Remote
Light Switch
Ground
Wires
Neutral
Wires
Ground
Screws
Figure 1
For optimal
range fully
extend the
antenna. Feed
antenna wire
between a gap
between the
switch box
and drywall.
Wall Plate
(existing-not provided)
Screws
(not provided)
Green
Wire
Inside
of cable
Yellow
Antenna
2
IMPORTANT NOTE: This illustration is ONLY an example and your
application and wiring may be different.
Press the switch to the
ON position. The light
should turn on.
Press the switch to the
OFF position. The light
should turn off.
Figure 2
TEST
Test the remote control operation at various locations within your
home for convenience and range. The remote control range will vary
depending on your house and wiring construction. The range may be
reduced by metal lath, foil-backed insulation or aluminum siding.
Press the remote control button. The light should turn on.
Press again and the light should turn off.
PROGRAMMING
2
3Then press and release the “LEARN”
button. Both the LED on the Smart Light
Switch and the light will flash once
indicating the programming is complete.
NOTE: If needed, press and release the
“LEARN” button with a narrow
instrument.
IMPORTANT NOTE: When the LED has stopped flashing (up to 10 minutes), proceed to Programming.
Press and release the Learn
button on the garage door
opener.
Press and HOLD the
remote control button. OROR
1Lift the cover on the Smart
Light Switch to access the
“LEARN” button.
• Download the
Chamberlain MyQ® App*.
• Create or sign-in to your
account and follow the
in-app instructions to add
the Smart Light Switch to
your MyQ® account.
* Smartphone control requires a MyQ®
Garage, Smart Garage Hub, MyQ®
Internet Gateway, or Wi-Fi® Garage
Door Opener.
3
Figure 4
Cover
3. Open the cover on the light switch so you can view the LED (Figure 4).
4. Allow up to 10 minutes for Smart Light Switch to power up properly, when the LED stops
flashing proceed to Programming.
INSTALLATION (CONTINUED)
Testing the Smart Light Switch will vary depending on your application.
REMOTE CONTROL
Activate the garage door opener. The light should turn on. The light
will stay on for the same length of time as your garage door opener
lights.
GARAGE DOOR OPENER
NOTE: If the light does not turn on and off, repeat programming steps.

Product specificaties

Merk: Chamberlain
Categorie: Niet gecategoriseerd
Model: WSLCEVC-P1

Heb je hulp nodig?

Als je hulp nodig hebt met Chamberlain WSLCEVC-P1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Chamberlain

Chamberlain

Chamberlain RZ94-05 Handleiding

12 November 2024
Chamberlain

Chamberlain 041-0192-000 Handleiding

10 Juni 2024
Chamberlain

Chamberlain MYQLED2 Handleiding

27 Mei 2024
Chamberlain

Chamberlain myQ-SGC2WCH Handleiding

30 Juni 2023
Chamberlain

Chamberlain myQ Smart Garage Video Keypad Handleiding

21 Juni 2023
Chamberlain

Chamberlain 041D9276 Handleiding

16 Mei 2023
Chamberlain

Chamberlain MYQ-G0301-E Handleiding

8 Mei 2023
Chamberlain

Chamberlain 041-0347-000 Handleiding

7 Mei 2023
Chamberlain

Chamberlain RPD15 Handleiding

6 Mei 2023
Chamberlain

Chamberlain 2025P Handleiding

5 Mei 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Xblitz

Xblitz R8 Power Charge Handleiding

3 December 2024
Xblitz

Xblitz R4 Power Handleiding

3 December 2024
Franke

Franke Urban UBG 610-78 Handleiding

3 December 2024
Franke

Franke ANX211RHD Handleiding

3 December 2024
Franke

Franke ANX220 Handleiding

3 December 2024
Dell

Dell NX3330 Handleiding

3 December 2024
Dell

Dell PowerConnect B-DCX-4s Handleiding

3 December 2024
Hager

Hager AKB83000701 Handleiding

3 December 2024
Hager

Hager AKB81500402 Handleiding

3 December 2024
Hager

Hager AKBA1500401V Handleiding

3 December 2024