Chamberlain CLDM1 Handleiding

Chamberlain Niet gecategoriseerd CLDM1

Lees hieronder de 📖 handleiding in het Nederlandse voor Chamberlain CLDM1 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 173 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

CLOSED

OPEN

Indoor Receiver

AC Adapter

Sensor

CR203 2

3 VOL TS

Lithium Battery

(CR2032 type)

Double-Sided

Fastening Strip

To prevent possible SERIOUS INJURY or DEATH from a closing garage

door:

• Activate door ONLY when it can be seen clearly, is properly adjusted,

and there are no obstructions to door travel.

• ALWAYS keep garage door in sight until completely closed. NEVER

permit anyone to cross path of closing garage door.

WARN

WARNWARNING

ING

INGING

GARAGE DOOR

MONITOR SYSTEM

PRE-INSTALLATION SYSTEM TEST

1. The sensor and receiver are pre-matched (programmed) at the

factory. Test the system by flipping the sensor over while it is a

few feet away from the receiver. The receiver will show a

green light for closed when the sensor is face up in the vertical

position with the of the case pointing down round end

(Figure 1). The red light will flash when the sensor is face

down in the horizontal position (Figure 2).

2. If the green or the red receiver lights do not come on, or do

not react as described, see the Troubleshooting or Learning

section of these instructions.

INSTALLING THE BATTERY IN THE GARAGE

DOOR INDICATOR SENSOR

1. Place the screw driver blade on the tab at

the end of the case and gently press down

and in toward the case.

2. Insert the the lithium battery into the battery

clip with the + (positive) side face up.

3. Push the case back together tightly by

inserting the top hooks into the back cover,

then snap shut the bottom of

the case.

NOTE: It is normal to hear a rattle from the tilt switch in the sensor

when tilted or rotated to another position.

INDOOR RECEIVER SETUP

1. Plug the AC adapter into any

standard 110 volt AC electrical

wall outlet and the small plug

into the back of the indoor

receiver.

2. The receiver has a 9" antenna

wire which comes out the

back. The antenna should be

straight and not touching

metal.

V OL

Figure 1 Figure 2

NOTE: Because radio control devices are inherently susceptible

to RF interference, this product should NOT be used as a

stand-alone security device. This product is considered a

monitoring and notification device ONLY, and as such, should not

be used as a substitute for a dedicated home security system.

To ensure that your Garage Door Monitor continues to operate

properly, the following checks should be performed on a

monthly basis:

• Check that the sensor is mounted properly on the garage door

(see Mounting the Sensor section of this manual.)

• Ensure the 3 volt lithium battery is installed properly.

• Check to see that the receiver system is plugged into a wall

outlet and the jack is properly connected to the back of the

receiver. Make sure the antenna is straight and not in contact

with any metal objects.

• Check that the receiver is properly recognizing sensor

signals (see Troubleshooting section of this manual.)

CL OSE D

Antenna Learn

Button

Adapter

Location

Garage Door Monitor

Model CLDM1

MOUNTING THE SENSOR

Attach the sensor to the inside of the garage door using the

double-sided fastening strip. Mount the sensor near the top of the

garage door for best results. The round end of the case should

be pointing down when the garage door is closed.

Inside of Garage

Double-Sided Fastening Strip

Round End

Down

Know when your garage door is open

or closed!

Thank you for purchasing the Chamberlain Garage Door Monitor.

Monitor the status of your garage door from inside your home. No

longer will you have to run downstairs or go outside just to see if

you or your children have left the garage door open.

GARAGE DOOR MONITOR OPERATION

When the receiver is powered up, both red and green LED’s

will blink once. The receiver will then show a solid green LED

until it receives a signal from a programmed sensor. The receiver

will display the current status of the programmed door sensor. If

no door sensor(s) is programmed to the receiver, the green and

red LED will flash simultaneously. See Learning section.

The sensor sends a closed signal when the garage door is

closed (vertical) and an open signal as the sensor changes to

open (horizontal) position.

Up to 4 door mounted sensors will work in conjunction with one

receiver.

The red LED will blink once every half-second if one or more of

the programmed sensors are not in the closed position. The

green LED comes on steady only when all the programmed

sensors are in the closed position.

NOTE: The system will sometimes take a few seconds to send a

signal. The sensor updates the receiver by transmitting an open

or closed signal every few minutes.

LEARNING MORE THAN ONE SENSOR(S)

1. Door must be closed and the green

LED on steadily.

2. Press and hold the learn button for 2

seconds, the receiver will enter the learn

mode. The green LED will blink on and

off in 1/2 second increments.

3. The additional sensor(s) must be moved

from a vertical position to a horizontal

position or vice versa.

4. Both green and red LED’s will turn on for 1 second to indicate

a successful learn. Upon success, the receiver immediately

exits the learn mode and returns to normal operation.

5. If no signal is received within 30 seconds, the receiver will exit

the learn mode and return to normal operation.

ERASING OR CLEARING THE MEMORY

1. Unplug the small plug from the AC adapter on the

indoor receiver.

2. Make sure the AC adapter is plugged into a wall outlet.

3. To erase the memory of all programmed sensors, press and

hold the learn button while plugging the small plug on the AC

adapter into the indoor receiver.

4. Both red and green LED’s will blink simultaneously. This also

indicates that no sensor(s) are in memory.

5. Proceed to Step 2 of Learning More Than One Sensor to

program the sensor to the receiver.

TROUBLESHOOTING

The sensor battery must be replaced every year to assure

consistent operation. Flashing of the red and green LED’s in a

special sequence normally indicates intermittent operation or a

dead battery.

Loss of signal: The sensor sends a signal periodically to

synchronize to the receiver. Should the receiver not receive the

signal in approximately 20 minutes, the red and green LED’s will

blink as follows. The green LED will blink once, then the red LED

will blink one to four times depending upon the sensor

number. This indicates the receiver has not received the signal

from this sensor for over 20 minutes and therefore

requires attention.

If replacing the battery does not rectify the issue, move the

receiver into the garage for additional troubleshooting. If the

monitor works flawlessly in close proximity, the sensor(s) signal is

being either blocked or interfered with in the previous location

and may require placement in a room closer to the garage

door(s).

Garage Door Monitor system just installed:

The sensor and receiver set are factory coded prior to shipment

and should work out of the package. If you encounter a situation

where the sensor and receiver work properly upon initial

installation, but show a loss of signal after 20 minutes you may

have an additional factory code in the receivers memory. In this

instance, the receiver will then appear to be unresponsive to the

sensor. In this instance, do the following:

1. Clear Receiver Memory – See Erasing or Clearing the

Memory section. Upon clearing memory, the receiver will

power up and show simultaneously flashing green and red

LED’s – this indicates that memory is cleared.

2. Proceed to Step 2 of Learning More Than One Sensor. Note

that the procedures to learn 1 sensor or multiple sensors are

the same.

If the receiver is still showing a loss of signal after following the

above procedure, then the receiver is located too far away from

the sensor. Relocate the receiver closer to the sensor.

Garage Door Monitor suddenly malfunctions after working

properly:

The sensors battery power is low. Replace the battery.

OPTIONAL ACCESSORIES

You can purchase additional sensors if you have more than one

garage door. The receiver will learn up to 4 sensors and the red

light will blink if any one of the garage doors is open.

ITEM PART #

Sensor CLDM 2

Indoor Receiver 2C507-3

12 Volt AC Adapter 2C508-2

Specifications:

Sensor

Battery: Lithium Type 2032. 1 year life.

Temperature: -180F to 1400F (-250C to 600C).

Codes: 254 randomly set codes.

Receiver

Power Supply: 12 volt DC, 50 mA.

Temperature: 140F to 1220F (-100C to 500C).

Codes: Learns codes of up to 4 sensors

FOR SERVICE DIAL OUR TOLL FREE NUMBER:

1-800-528-9131

Press

and Hold

the Learn

Button

NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of

this receiver and/or transmitter are prohibited, except for changing the code setting or replacing

the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired operation.

CLOSED

OPEN

Receptor Interior

Adaptador de CASensor

CR203 2

3 VOL TS

Pila de Litio

(tipo CR2032) Tira Sujetadora de Dos Lados

Para prevenir una LESIÓN GRAVE o la MUERTE de una puerta cerrante de un

garage:

• Active la puerta SOLO cuando pueda verse claramente, esté bien ajustada, y no

hay obstrucciones al recorrido de la puerta.

• SIEMPRE mantenga la puerta del garage a la vista hasta que esté

completamente cerrada. NUNCA permita que nadie cruce el recorrido de la

puerta del garage mientras se está cerrando.

ADVERTENCIA

ADVERTENCIAADVERTENCIA

SISTEMA DE

MONITOREO DE

LA PUERTA DEL GARAJE

PRUEBA DE PREINSTALACIÓN DEL SISTEMA

1. El sensor y el receptor se hacen corresponder (programados) de

fábrica. Pruebe el sistema invirtiendo el sensor mientras está a unos

pocos pies del receptor. El receptor muestra una luz verde cuando

está cerrado cuando el sensor está orientado hacia arriba en la

posición vertical con el de la caja apuntando haciaextremo redondo

arriba (Figura 1). La luz roja centellea cuando el sensor está orientado

hacia abajo en la posición horizontal (Figura 2).

2. Vea la sección de Localización de Fallas o de Aprendizaje de estas

instrucciones, si las luces verde o de receptor roja no se encienden, o

no reaccionan según se describe.

INSTALACION DE LA PILA EN EL SENSOR

INDICADOR DE LA PUERTA DEL

GARAJE

1. Coloque la hoja del destornillador la aleta alen

extremo de la caja y presione suavemente hacia

abajo y hacia adentro hacia la caja.

2. Inserte la pila de litio dentro del broche de la pila

con el lado + (positivo) hacia arriba.

3. Cierre bien la caja insertando los ganchos

superiores dentro de la cubierta posterior, a

continuación calce cerrada el fondo de la caja.

NOTA: Es normal escuchar un sonido metálico del

conmutador de inclinación en el sensor cuando está inclinado o girado a

otra posición.

PREPARACION DEL RECEPTOR INTERIOR

1. Enchufe el adaptador de CA dentro

de cualquier tomacorrientes

eléctrico de pared de 110 voltios de

CA y el enchufe pequeño dentro de

la parte inferior del receptor Interior.

2. El Receptor tiene un cable de

antena de 9" que sale de la parte

posterior. La antena debe estar

recta y no tocar el metal.

V O

Figure 1 Figure 2

NOTA: A causa que los dispositivos de control por radio son

inherentemente susceptibles a la interferencia RF, este producto NO debe

usarse como un dispositivo de seguridad exclusivo. Este producto se

considera un dispositivo de monitoreo y notificación SOLAMENTE, y

como tal no debe usarse como un substituto para un sistema dedicado

de seguridad del hogar.

Deben efectuarse las inspecciones siguientes mensualmente, para

asegurar que el monitor de su puerta de garaje funcione apropiadamente:

• Inspeccione que el sensor esté montado apropiadamente en la puerta

del garaje (vea la sección de de este manual). Montaje del sensor

• Asegúrese que la pila de litio de 3 voltios esté instalada

apropiadamente.

• Inspeccione para verificar que el sistema receptor esté enchufado a un

tomacorrientes de pared y el jack esté conectado apropiadamente a la

parte posterior del receptor. Asegúrese que la antena esté recta y sin

contacto con objetos de metal.

• Verifique que el receptor reconozca apropiadamente las señales del

sensor (vea la sección de Localización de fallas de este manual.)

CL OS ED

OP EN

Antena Botón de

Aprendizaje

Ubicación del

Adaptador

de CA

Monitor de puerta de garaje

Model CLDM1

MONTAJE DEL SENSOR

Fije el sensor al interior de la puerta del garaje usando el tira sujetadora

de dos lados. Monte el sensor cerca del tope de la puerta del garaje para

obtener los mejores resultados. El de la caja debeextremo redondo

apuntar hacia abajo cuando la puerta del garaje está cerrada.

Interior Del Garaje

Tira Sujetadora de Dos Lados

Extremo Redondo

Orientado

Hacia Abajo

¡Sepa cuando la puerta del garaje está abierta

o cerrada!

Gracias por comprar el monitor de puerta de garaje Chamberlain. Vigile el

estado de la puerta de su garaje desde el interior de su casa. Nunca más

va a tener que bajar las escaleras o salir sólo para ver si sus niños han

dejado abierta la puerta del garaje.

Product specificaties

Merk:	Chamberlain
Categorie:	Niet gecategoriseerd
Model:	CLDM1
Kastontwerp:	Behuizing
Stroomverbruik:	50 mA
Maximum aantal deuren:	4 deur(en)
Ingebouwde UPS:	Nee
Aantal codes:	254