Chamberlain 45ACT Handleiding

Chamberlain Niet gecategoriseerd 45ACT

Lees hieronder de 📖 handleiding in het Nederlandse voor Chamberlain 45ACT (13 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 172 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/13

DANGER s P ELIGRO

132C2280- 3D

TO ERASE ALL

RECEIVER CODES

1. Pre ss and HOLD

re ce iver or ange

ERASE butt on

6 se co nds . Indica to r

light will t urn ON.

2. Re le ase butt on

whe n light tu rns OFF.

CANADA:

PART NO.: NO. DE PIEZ A:

DATE:

T HE CHAMB ERLAIN

GRO UP, IN C., US A

Ens am blad o e n Méxi co

Ass em bled in Me xico

ELIMINACIÓN DE

TODOS LOS CÓDIGOS DEL

RECEP TOR

1. MANTE NGA PRE SIONADO

e l bo t ón nar anja " ERASE "

de l re ce pto r dura nte 6

se gundo s. La luz de l

indica dor s e e nce nde rá .

2. Sue lte e l bo t ón cua ndo la

luz se apa gue.

DANGER s PELIGRO

132C2280-3D

TO ERASE ALL

RECEIV ER CODE S

1. Press and HOL D

receiver orang e

ERASE b u tto n

6 secon d s. In d icato rlig h t wi ll tu rn ON.

2. Release bu tto n

when lig h t tu rns OF F.

CANADA:

PART NO.: N O. DE PIEZA:

DATE:

THE C H A MB ERLA IN

GROU P, I N C. , U SA

Ensamblado en México

Assembled in Mexico

ELIM INAC IÓN DE

TODOS LOS C ÓDIGOS DEL

RECEP TOR

1. MANTENGAPRE SION ADO

el b o tó n naranja "ERASE "

d el receptor d urante 6 segund o s. L a lu z d el

ind i cado r se encenderá.

2. Suelte el b o t ó n cuand o l a

luz se apagu e.

Before you begin

Installation

RECEIVER LOGIC BOARD REPLACEMENT

Model 45ACT

1.2 To maintain your warranty, place the

provided label over the existing label on

the end panel of the garage door opener.

1.1 Remove the light lens by pulling the top

sides of the light lens and rotate the light

lens down. Squeeze the light lens clips to

remove lens from end panel.

NOTE: The products illustrated in the instructions are for reference. Your product may look different.

1.3 Disconnect power to the garage door

opener.

Remove the receiver logic board

2.1 Disconnect the wires from the quick-connect terminals ( ). A

Remove the receiver logic board end panel from the garage

door opener.

2.2 Unplug the wire harnesses from the receiver logic

board. You may need needle-nosed pliers, to

remove the harnesses.

2.3 Remove the receiver

logic board from the

end panel by removing

the 2 screws and

releasing the 2 clips.

To prevent possible SERIOUS INJURY or

DEATH:

• Disconnect ALL electric and battery

power BEFORE performing ANY service

or maintenance.

To prevent damage to the receiver/logic

board, DO NOT touch printed circuit board

of replacement receiver/logic board during

installation.

ALWAYS wear protective gloves and eye

protection when changing the battery or

working around the battery compartment.

Screws

Clips

To insert or remove

the wires from the

terminal, push in the

tab with a

screwdriver tip.

Red

White

Grey

WARNING: This product can expose you to chemicals including lead, which are known to the State of California to cause cancer or birth

defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

Install new receiver logic board

3.1 Connect the wire harnesses to

the new receiver logic board.

3.3 Reinsert the wires.

Door control wires:

• white wire into the white terminal.

• white/red wire into the red terminal.

Safety sensor wires:

• white wires into the white terminal.

• white/black wires into the

grey terminal.

NOTE: A TEST OF THE SAFETY REVERSE SYSTEM IS NECESSARY FOR SAFE OPERATION.

To insert or remove the wires

from the terminal, push in the

tab with a screwdriver tip.

Programming

1.1 Press and release the Learn button on the garage door opener. The Learn indicator light will

glow steadily for 30 seconds.

1.2 Within 30 seconds, press and hold the

button on the remote control.

1.3 Release the button when the garage door

opener light blinks. It has learned the

code. If light bulbs are not installed, two

clicks will be heard.

Program a remote using the learn button

Learn

Indicator

Light

Yellow Learn

Button

3.4 Install the light lens by aligning with

the hinges and snapping into place.

Reconnect power.

NOTE: When installing the light lens, ensure the antenna

wires are hanging straight down.

3.2 Insert the antenna wires through the holes in

the end panel. Snap the receiver logic board into

place on the end panel and fasten with screws.

NOTE: Some models will

require the short antenna

wire to be placed in the

traps of the end panel.

Antenna wires

Antenna

wires

Red

White

Grey

Program the travel

Without a properly installed safety reversal

system, persons (particularly small children)

could be SERIOUSLY INJURED or KILLED by

a closing garage door.

• Incorrect adjustment of garage door travel

limits will interfere with proper operation

of safety reversal system.

• After ANY adjustments are made, the

safety reversal system MUST be tested.

Door MUST reverse on contact with 1-1/2"

(3.8 cm) high object (or 2x4 laid ﬂ at) on

ﬂ oor.

1.1 Press and hold the Adjustment Button

until the UP Button begins to ﬂ ash and/

or a beep is heard.

1.2 Press and hold the UP Button until the

door is in the desired UP position.

1.3 Once the door is in the desired

UP position press and release the

Adjustment Button. The garage door

opener lights will ﬂ ash twice and the

DOWN Button will begin to ﬂ ash.

NOTE: The UP and DOWN Buttons can be used to move

the door up and down as needed.

1.4 Press and hold the DOWN Button

until the door is in the desired DOWN

position.

NOTE: The UP and DOWN Buttons can be used to move

the door up and down as needed.

1.5 Once the door is in the desired

DOWN position press and release the

Adjustment Button. The garage door

opener lights will ﬂ ash twice and the UP

Button will begin to ﬂ ash.

1.6 Press and release the UP Button.

When the door travels to the

programmed UP position, the DOWN

Button will begin to ﬂ ash.

1.7 Press and release the DOWN Button.

The door will travel to the programmed

DOWN position. Programming is

complete.

* If the garage door opener lights are ﬂ ashing 5 times during the steps for Program the Travel, the programming has timed out. If the garage door opener lights are ﬂ ashing 10 times during the steps for

Program the Travel, the safety reversing sensors are misaligned or obstructed. When the sensors are aligned and unobstructed, cycle the door through a complete up and down cycle using the remote

control or the UP and DOWN buttons. Programming is complete. If you are unable to operate the door up and down, repeat the steps for Programming the Travel.

Adjustment