Chamberlain 050DCTBLKMC Handleiding

Chamberlain Niet gecategoriseerd 050DCTBLKMC

Lees hieronder de 📖 handleiding in het Nederlandse voor Chamberlain 050DCTBLKMC (12 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 13 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

Before you begin

Installation

RECEIVER LOGIC BOARD REPLACEMENT

Models 050DCTBMC and 050DCTBLKMC

1.2 To maintain your warranty,

place the provided label

over the existing label

on the end panel of the

garage door opener.

1.1 Remove the light lens by pulling

the top side of the light lens

and swing the light lens down.

Squeeze the light lens clips to

remove lens from end panel.

1.3 Disconnect electrical and battery

power (if applicable) to the

garage door opener.

Remove the receiver logic board

2.1 Disconnect the wires from the quick-connect terminals

( ). Disconnect any wires from the lock terminals. A

Remove the receiver logic board end panel from the

garage door opener.

2.2 Unplug the wire harnesses from the receiver logic

board. You may need needle-nosed pliers, to

remove the harnesses.

2.3 Remove the receiver

logic board from the

end panel by removing

the 2 screws and

releasing the 2 clips.

To prevent possible SERIOUS INJURY or DEATH:

• Disconnect ALL electric and battery power BEFORE performing ANY

service or maintenance.

Screws

Wire clip

Clips

To insert or remove the wires from the terminal,

push in the tab with a screwdriver tip.

Lock

Terminals

Red

White

Grey

Your garage door opener has an internal gateway located on the receiver logic board. After installing the new receiver logic board, use the myQ

® serial number found on the provided label to add your

garage door opener to your myQ® account. The products illustrated in the instructions are for reference. Your product may look different. The logic board ﬁrmware has been updated. The update provides

a new Obstruction Notiﬁcation that signals when the opener senses resistance, such as an obstruction or other binding in the door and rail system. The door will stop or reverse to open limit and the

opener will beep and the lights ﬂash 5 times.

WARNING: This product can expose you to chemicals including

lead, which are known to the State of California to cause cancer or

birth defects or other reproductive harm. For more information go

to www.P65Warnings.ca.gov.

To prevent damage to the receiver/logic board, DO NOT touch printed

circuit board of replacement receiver/logic board during installation.

ALWAYS wear protective gloves and eye protection when changing the

battery or working around the battery compartment.

NOTE: 050DCTB replaces 050DCTWF and 050DCTBLK replaces 050DCTWFLK. 050DCTBMC replaces DCTB/DCTWF, and DCTBLKMC replaces DCTBLK and DCTWFLK.

Front of Logic Board

End Panel

Button Pad

Back of Logic Board

Install new receiver logic board

3.1 Connect the wire harnesses to the

new receiver logic board. When

reconnecting the wire harness, be sure

the tabs on the wire harness are facing

the end panel, not the logic board.

3.3 Reinsert the wires.

Door control wires:

• white wire into the white terminal.

• white/red wire into the red terminal.

Safety sensor wires:

• white wires into the white terminal.

• white/black wires into the

grey terminal.

Reconnect any lock terminal wires.

NOTE: A test of the safety reverse system is necessary for safe operation.

To insert or remove the wires from

the terminal, push in the tab with a

screwdriver tip.

Programming

1.1 Press and release the Learn button on the garage door opener. The Learn indicator light will

glow steadily for 30 seconds.

1.2 Within 30 seconds, press and hold the

button on the remote control.

1.3 Release the button when the garage door

opener light blinks. It has learned the

code. If light bulbs are not installed, two

clicks will be heard.

Program a remote using the learn button

Learn

Indicator

Light

Yellow Learn

Button

3.4 Install the light lens by aligning with

the hinges and snapping into place.

Reconnect power.

NOTE: When installing the light lens, ensure the

antenna wires are hanging straight down.

Red

White

Grey

Logic Board

Wire Clip

End Panel

Wire

Harness

Tabs

3.2 Insert the antenna wires through

the holes in the end panel. Snap the

receiver logic board into place on the

end panel and fasten with screws.

NOTE: Some

models will require

the short antenna

wire to be placed in

the traps of the end

panel.

Antenna wires

Antenna

wires

To program the Wi-Fi garage door opener to your network refer to your owner’s manual.

For garage door openers without a battery

back up system: remove the button pad from

the logic board and replace it with the alternate

button pad.

NOTE: If your logic board

has a wire clip, use the

wire clip to hold wires to

the logic board.

Lock

Terminals

Program the travel

Without a properly installed safety reversal

system, persons (particularly small children)

could be SERIOUSLY INJURED or KILLED by

a closing garage door.

• Incorrect adjustment of garage door travel

limits will interfere with proper operation

of safety reversal system.

• After ANY adjustments are made, the

safety reversal system MUST be tested.

Door MUST reverse on contact with 1-1/2"

(3.8 cm) high object (or 2x4 laid ﬂat) on

ﬂoor

While programming the travel, the UP

and DOWN buttons can be used to move

the door as needed. The Safety Reversing

Sensors will be disconnected during

the Program the Travel process. During

the Automatic Force Setup the door will

automatically open and close.

1.1 Press and hold the Adjustment Button

until the UP Button begins to ﬂash and/

or a beep is heard.

The Safety Reversing Sensors will be

disconnected during the Program the Travel

process.

1.2 Press and hold the UP Button until the

door is in the desired UP position.

1.3 Once the door is in the desired

UP position press and release the

Adjustment Button. The garage door

opener lights will ﬂash twice and the

DOWN Button will begin to ﬂash.

1.4 Press and hold the DOWN button

until the door is in the desired DOWN

position.

1.5 Once the door is in the desired DOWN

position press and release the Adjustment

Button. The garage door opener lights will

ﬂash twice. Program the Travel is now

complete. If the garage door opener lights

ﬂash 5 times, then programming has timed

out and the Travel Limits have not been set.

Please restart the Program the Travel process.

1.6 Add the Step Save sticker under the

yellow program button.

Once both the up and down positions have been manually set, the Safety Reversing Sensors

will reconnect and become operational. Then, the opener will enter a force-sensing operation by

automatically moving the door open and close. The garage door opener will sound an audible and

visual alert before automatically opening and closing the door. The garage door opener will beep

three times, conﬁrming that the Automatic Force Setup completed successfully. Adjustment is

complete.

If you hear one long beep after the door attempts to move, then the Automatic Force Set Up has

not completed successfully. Please start over at step 1 of Program the Travel..

Adjustment

Automatic Force Set Up

Product specificaties

Merk:	Chamberlain
Categorie:	Niet gecategoriseerd
Model:	050DCTBLKMC

Heb je hulp nodig?

Als je hulp nodig hebt met Chamberlain 050DCTBLKMC stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Chamberlain

Chamberlain RZ94-05 Handleiding

12 November 2024

Chamberlain 041-0192-000 Handleiding

10 Juni 2024

Chamberlain MYQLED2 Handleiding

27 Mei 2024

Chamberlain myQ-SGC2WCH Handleiding

30 Juni 2023

Chamberlain myQ Smart Garage Video Keypad Handleiding

21 Juni 2023

Chamberlain 041D9276 Handleiding

16 Mei 2023

Chamberlain MYQ-G0301-E Handleiding

8 Mei 2023

Chamberlain 041-0347-000 Handleiding

7 Mei 2023

Chamberlain RPD15 Handleiding

6 Mei 2023

Chamberlain 2025P Handleiding

5 Mei 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Gourmetmaxx 03863 Handleiding

24 December 2024

Vello PGS-P Handleiding

24 December 2024

Venom Quad Charging Station VS4796 Handleiding

24 December 2024

Nec IPJ2000CM Handleiding

24 December 2024

Monogram ZKPN Handleiding

24 December 2024

Philips Quick Clean Pot QCP10 Handleiding

24 December 2024

Philips Senseo HD7002 Handleiding

24 December 2024

D-Link DUB-C2 Handleiding

24 December 2024

Nec MultiPresenter Stick DS1-MP10RX1 Handleiding

24 December 2024

Nec DS1-TM01 Handleiding

24 December 2024