Chamberlain 041A7928-3MC Handleiding

Chamberlain Niet gecategoriseerd 041A7928-3MC

Lees hieronder de 📖 handleiding in het Nederlandse voor Chamberlain 041A7928-3MC (12 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 213 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

INTERNET CONNECTIVITY KIT

MODEL 41A7928-3

To prevent possible SERIOUS INJURY or DEATH from electrocution:

• Be sure power is NOT connected BEFORE installing door control.

• Connect ONLY to 7-28 VOLT low voltage wires.

To prevent possible SERIOUS INJURY or DEATH from a closing garage

door:

• Install door control within sight of garage door, out of reach of

children at a minimum height of 5 feet (1.5 m), and away from ALL

moving parts of door.

• NEVER permit children to operate or play with door control push

buttons or remote control transmitters.

• Activate door ONLY when it can be seen clearly, is properly adjusted,

and there are no obstructions to door travel.

• ALWAYS keep garage door in sight until completely closed. NEVER

permit anyone to cross path of closing garage door.

• DO NOT install this door control on garage door opener systems

controlling one-piece or swing doors.

To provide an adequate visual alert, the garage door opener light bulb(s)

MUST be a minimum of 40 Watt (or equivalent).

WARNING

This kit includes the myQ® Control Panel model 41A7928-3 and the

Chamberlain® Internet Gateway model CIGBU. The myQ Control Panel is

intended to be installed with Security:™ Garage Door Openers

manufactured between 1998 and present. The myQ Control Panel is NOT

compatible with Security: 2.0™ Garage Door Openers. DO NOT install this

door control on garage door opener systems controlling one-piece or swing

doors.

APPLICATION

The myQ Control Panel offers a quick and convenient way to add Security

2.0™ and myQ technology to your existing garage door opener. myQ

technology uses a 900MHz signal to provide two-way communication

between the garage door opener and myQ enabled accessories. When

programmed to the Chamberlain® Internet Gateway you can monitor and

control your garage door from any internet enabled computer or

smartphone. You may program up to 12 Security 2.0™ remote controls,

2 Security 2.0™ keyless entries and a combination of 16 myQ

accessories to the myQ control panel. For full compatibility, see page 4.

OVERVIEW

Install the control panel in place of the existing door control. Due to power

consumption the control panel cannot be used in conjunction with another

wired door control connected to your garage door opener. If an additional

door control is needed, the can be wireless door control model 41A7773-1

programmed to the control panel. To program the 41A7773-1 to the control

panel, follow the remote control programming steps. When in battery back-

up mode, any feature using unattended operation such as Timer-to-Close,

closure from a garage door and gate monitor or remote operation utilizing

the Chamberlain®

Internet Gateway will be disabled.

1. Disconnect all electrical and battery power (if applicable) to the

garage door opener.

2. Remove the existing door control from the wall.

3. Note the polarity of the wires connected to the existing door control.

• Label the wire connected to the RED terminal.

• Label the wire connected to the WHITE terminal.

Disconnect the wires from the existing door control.

4. Connect the wires to the new myQ Control Panel. Make sure the

polarity is correct.

• Red wire to the R terminal.

• White wire to the W terminal.

5. Mount the control panel to the wall.

6. Reconnect power. The yellow command LED and the red learn LED

will blink quickly for up to 5 minutes as the control panel recharges.

When the control panel is operational, the yellow command LED will

glow steadily.

7. To test the control panel, press the push bar to activate the garage

door opener.

INSTALL THE Q CONTROL PANELmy

Existing Door Control

Discard, donate

or recycle

Wire from RED

terminal

Connect

RED wire to

R terminal

Wire from

WHITE

terminal

Connect

WHITE

wire to W

terminal

myQ Control Panel

• If the yellow command LED does not turn on, reverse the wires

connected to the R and W terminals of the control panel. Replace

wire if necessary.

• If yellow and red LEDs are blinking slowly, the control panel is not

compatible with your garage door opener.

• If the yellow and red LEDs are blinking quickly, the control panel is

charging, and may take up to 5 minutes to become operational.

TROUBLESHOOTING

The Chamberlain® Internet Gateway gives you control of your garage door

from your internet connected computer or smart phone.

1 CONNECT THE CHAMBERLAIN® INTERNET GATEWAY

1.1 Connect the Chamberlain® Internet Gateway to a router with the

ethernet cable. If you only have access to a Wi-Fi signal and not a

router, you must use a wireless ethernet adapter (not provided) to

connect to the internet.

1.2 Connect power to the Chamberlain® Internet Gateway. The blue and

green LEDs will blink momentarily and then the green LED will light

solid.

2 CREATE AN ACCOUNT

From your computer, go to www.mychamberlain.com and follow the

instructions to create an account. Use a computer for this step; you

cannot create an account from a mobile device.

3 REGISTER THE CHAMBERLAIN® INTERNET GATEWAY

number from the label on the bottom of the device.

4 PROGRAM THE my Q CONTROL PANEL TO THE

CHAMBERLAIN® INTERNET GATEWAY

4.1 Click on “Manage Places>Add New Device>Garage Door Opener”

and follow the directions.

4.2 Once you click ADD you have 3 minutes to press the LEARN button

two times on the myQ control panel. The red learn LED will turn on.

4.3 The red learn LED will turn off when programming is complete. The

blue LED on the Chamberlain® Internet Gateway will light to indicate

that a device has been learned. Once the control panel is learned, it

will appear on your screen and you can then name the device (e.g.,

My Control Panel, etc.).

4.4 Click SAVE.

The control panel has now been programmed to the internet gateway and

the garage door can now be controlled from a computer or smartphone.

Follow the same steps to add other myQ devices.

DOWNLOAD THE SMARTPHONE APP

Visit the app store for your smartphone to download the myQ app. With the

app you can monitor and control your garage door opener and myQ devices.

You can also add or remove other myQ accessories.

INSTALL THE CHAMBERLAIN® INTERNET GATEWAY

Chamberlain® Internet Gateway

Router

Ethernet

Cable

Power

Adapter

Green LED

Blue LED

2 3

www.mychamberlain.com

After power up, the LED lights will show the status of the Chamberlain®

Internet Gateway.

• GREEN On Solid – The Chamberlain® Internet Gateway has an IP

address and is connected to the Internet.

• GREEN flashing steadily On & Off – The Chamberlain® Internet

Gateway has an IP address, but is not accessing the internet. Check

your router settings and internet connections.

• GREEN Off – The router is not providing an IP address to the

Chamberlain® Internet Gateway. Check your router settings and

internet connections.

TROUBLESHOOTING

PUSH BAR

Press the push bar to open/close the door.

LIGHTS

Press the LIGHT button to turn the garage door opener lights on or off.

When the lights are turned on they will stay on until the LIGHT button is

pressed again, or until the garage door opener is activated. Once the

garage door opener is activated the lights will turn off after the specified

period of time (the factory setting is 4-1/2 minutes). The LIGHT button will

not control the lights when the door is in motion.

To change the amount of time the garage door opener lights will stay on:

Press and hold the LOCK button until the garage door opener lights flash.

The time interval is indicated by the number of flashes.

MOTION SENSOR

This feature will automatically turn on the garage door opener lights when

motion is sensed. The lights will come on for the set period of time, then

shut off.

Activate/Deactivate:

Slide the motion sensor switch ON or OFF.

TIMER-TO-CLOSE (TTC)

NOTE: DO NOT install this door control on garage door opener systems

controlling one-piece or swing doors.

The TTC feature automatically closes the door after a specified time period

(1, 5, or 10 minutes). Once the TTC has been set and the door is open, the

LED for the selected close interval will blink and begin to count down to

close the door. The control panel will beep and the garage door opener

lights will flash before closing the door.

The TTC feature will deactivate if the garage door encounters an

obstruction twice; or the safety reversing sensors are incorrectly installed.

The garage door will reverse open and WILL NOT close until the

FUNCTIONS

NUMBER OF TIMES GARAGE

DOOR OPENER LIGHTS FLASH 1 2 3 4

TIME THE GARAGE DOOR

OPENER LIGHT STAYS ON

1 ½

Minutes 2 ½

Minutes 3 ½

Minutes 4 ½

Minutes

obstructions are clear or the safety reversing sensors are correctly

installed. When the obstruction has been cleared or the safety reversing

sensors have been aligned, the door will close when the garage door

opener is activated.

Activate:

Press and hold the ON button until one of the TTC LEDs light up. Then

press the ON button again to cycle through the time interval options (the

corresponding TTC LED will light for each time interval). The garage door

opener light bulbs will blink as confirmation.

Deactivate:

Press and hold the OFF button until all TTC LEDs turn off and a beep is

heard from the control panel.

Temporarily hold door open (suspend TTC):

Press and release the HOLD OPEN button. The HOLD OPEN button will

begin to flash. Press the HOLD OPEN button again to resume normal TTC

operation.

LOCK

Activate*:

Press and hold the LOCK button for 2 seconds. The command LED will

flash as long as the lock feature is activated and your handheld remote

control will not operate your door at this time.

Deactivate:

Press and hold the LOCK button again for 2 seconds. The command LED

will stop flashing and normal operation will resume.

* Your Chamberlain® keypad will continue to work when LOCK has

been activated.

ERASE DEVICES FROM MEMORY

Erase all remote controls and keyless entries:

1. Press and hold the LEARN button on the control panel until the red

learn LED goes out (approximately 6 seconds). All remote control

and keyless entry codes are now erased. Reprogram any compatible

accessory you wish to use.

NOTE: Erasing remote controls and keyless entries from the control panel does

not erase them from the garage door opener, you need to erase the memory

of the garage door opener separately.

Erase all devices (including myQ enabled accessories):

1. Press and hold the LEARN button on the control panel until the red

learn LED goes out (approximately 6 seconds).

2. Immediately press and hold the LEARN button again until the red

learn LED goes out. All codes are now erased. Reprogram any

compatible accessory you wish to use.

LIGHT

Button

1 Minute

TTC LED

5 Minute

TTC LED

10 Minute

TTC LED

ON Button

Command LED

(yellow)

OFF Button

HOLD OPEN

Button

Motion

Sensor

LEARN

button

Learn LED

(Red)

LOCK

button

Push Bar (Open)

Product specificaties

Merk:	Chamberlain
Categorie:	Niet gecategoriseerd
Model:	041A7928-3MC

Heb je hulp nodig?

Als je hulp nodig hebt met Chamberlain 041A7928-3MC stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Chamberlain

Chamberlain RZ94-05 Handleiding

12 November 2024

Chamberlain 041-0192-000 Handleiding

10 Juni 2024

Chamberlain MYQLED2 Handleiding

27 Mei 2024

Chamberlain myQ-SGC2WCH Handleiding

30 Juni 2023

Chamberlain myQ Smart Garage Video Keypad Handleiding

21 Juni 2023

Chamberlain 041D9276 Handleiding

16 Mei 2023

Chamberlain MYQ-G0301-E Handleiding

8 Mei 2023

Chamberlain 041-0347-000 Handleiding

7 Mei 2023

Chamberlain RPD15 Handleiding

6 Mei 2023

Chamberlain 2025P Handleiding

5 Mei 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Gourmetmaxx 03863 Handleiding

24 December 2024

Vello PGS-P Handleiding

24 December 2024

Venom Quad Charging Station VS4796 Handleiding

24 December 2024

Nec IPJ2000CM Handleiding

24 December 2024

Monogram ZKPN Handleiding

24 December 2024

Philips Quick Clean Pot QCP10 Handleiding

24 December 2024

Philips Senseo HD7002 Handleiding

24 December 2024

D-Link DUB-C2 Handleiding

24 December 2024

Nec MultiPresenter Stick DS1-MP10RX1 Handleiding

24 December 2024

Nec DS1-TM01 Handleiding

24 December 2024