Chamberlain 041A5021-H-315 Handleiding

Chamberlain Niet gecategoriseerd 041A5021-H-315

Lees hieronder de 📖 handleiding in het Nederlandse voor Chamberlain 041A5021-H-315 (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 7 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

To prevent possible SERIOUS INJURY or DEATH from electrocution,

disconnect power to opener BEFORE proceeding.

To prevent damage to the receiver/logic board, do not touch the printed

circuit board of the replacement receiver/logic board during installation.

REPLACING RECEIVER/LOGIC

PANEL ASSEMBLY

WARNING: This product can expose you to chemicals including

lead, which are known to the State of California to cause cancer or

birth defects or other reproductive harm. For more information go to

www.P65Warnings.ca.gov.

This assembly is a replacement for your original receiver/logic

panel assembly. See side two for code programming instructions.

Depending on model type, you may have to remove the light lens

before proceeding with replacement part installation. The receiver/

logic panel assembly is located as shown below with corresponding

garage door opener models. The light lens is removed.

1. Disconnect all wires from the terminal screws of your opener’s

receiver/logic panel assembly, noting color of wires.

2. Remove screws to disengage the assembly from the opener

chassis.

3. Disconnect assembly from opener by holding the wire connector

plug and pulling down on the panel.

4. Install replacement assembly by reversing previous steps.

Connector plug is polarized. Take care to seat it properly and do

not force connection.

5. Re-connect power.

NOTE: A test of the safety reverse system is necessary for safe

operation. Instructions are on page two and in your opener’s manual.

Open and close force settings may also require adjustment. Refer to

your owner’s manual.

CAUTION

Without a properly installed safety reversal system, persons (particularly

small children) could be SERIOUSLY INJURED or KILLED by a closing

garage door.

• Safety reversal system MUST be tested every month.

• If one control (force or travel limits) is adjusted, the other control may

also need adjustment.

• After ANY adjustments are made, the safety reversal system MUST be

tested. Door MUST reverse on contact with 1-1/2” (3.8 cm) high

object (or 2x4 laid flat) on the floor.

Select a remote control push button to operate the opener.

1. Press and hold the selected remote control push button

2. Then press and release the “SMART” (Learn) button on the opener

panel. The opener light will flash once.

3. Release the remote control push button.

Now the opener will operate when the remote push button is pressed.

NOTE: If you release the remote control push button before the

opener light flashes, the receiver will not learn the code.

Garage Door Opener

(With “Smart” Button)

“Smart” (learn)

Button

Indicator Light

Kg Kg

1 2 3

Select a

push button

• Press and hold the “SMART” button on the opener panel until the

indicator light turns off (about 6 seconds). ALL the codes the

opener has learned will be erased.

• To reprogram, repeat Steps 1–3 for each remote control in use.

Code programming instructions are also located on the opener

panel.

Conduct the Safety Reverse Test After:

• Each adjustment of door arm length, force controls or limit

controls.

• Any repair to or adjustment of the garage door (including springs

and hardware).

• Any repair to or buckling of the garage floor.

• Any repair or adjustment to the opener.

• Place a one-inch board (or a 2x4 laid flat) on the floor, centered

under the garage door.

• Operate the door in the down direction. The door must reverse on

striking the obstruction.

If the door stops on the obstruction, it is not traveling far enough in

the down direction.

• Increase the DOWN limit by turning the DOWN limit adjustment

screw counterclockwise 1/4 turn.

• Repeat the test.

NOTE: On a sectional door, make sure limit adjustments do not force

the door arm beyond a straight up and down position.

• When the door reverses on the one-inch board, remove the

obstruction and run the opener through 3 or 4 complete travel

cycles to test adjustment.

NOTE: If the door will not reverse after repeated adjustment attempts,

call for professional garage door service.

WAR

ARN

NING

ING

Product specificaties

Merk:	Chamberlain
Categorie:	Niet gecategoriseerd
Model:	041A5021-H-315

Heb je hulp nodig?

Als je hulp nodig hebt met Chamberlain 041A5021-H-315 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Chamberlain

Chamberlain RZ94-05 Handleiding

12 November 2024

Chamberlain 041-0192-000 Handleiding

10 Juni 2024

Chamberlain MYQLED2 Handleiding

27 Mei 2024

Chamberlain myQ-SGC2WCH Handleiding

30 Juni 2023

Chamberlain myQ Smart Garage Video Keypad Handleiding

21 Juni 2023

Chamberlain 041D9276 Handleiding

16 Mei 2023

Chamberlain MYQ-G0301-E Handleiding

8 Mei 2023

Chamberlain 041-0347-000 Handleiding

7 Mei 2023

Chamberlain RPD15 Handleiding

6 Mei 2023

Chamberlain 2025P Handleiding

5 Mei 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Gourmetmaxx 03863 Handleiding

24 December 2024

Vello PGS-P Handleiding

24 December 2024

Venom Quad Charging Station VS4796 Handleiding

24 December 2024

Nec IPJ2000CM Handleiding

24 December 2024

Monogram ZKPN Handleiding

24 December 2024

Philips Quick Clean Pot QCP10 Handleiding

24 December 2024

Philips Senseo HD7002 Handleiding

24 December 2024

D-Link DUB-C2 Handleiding

24 December 2024

Nec MultiPresenter Stick DS1-MP10RX1 Handleiding

24 December 2024

Nec DS1-TM01 Handleiding

24 December 2024