CDN SD1110X Handleiding

CDN Keukenweegschaal SD1110X

Lees hieronder de 📖 handleiding in het Nederlandse voor CDN SD1110X (4 pagina's) in de categorie Keukenweegschaal. Deze handleiding was nuttig voor 43 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Features

• NSF® Certied

• Submersible (IP67: protected from water up to 3 feet

for 30 minutes, completely protected against dust)

• Programmable

• Tare function

• Backlit display

• Field calibration

• Low/high limit alerts

• Selectable units

• Stability indication

• Overload indication

• Battery status indication

• Stainless steel housing

• Removable stainless steel platform

• On/off button

• Auto-off after 2 minutes, programmable to 5 minutes;

disabled when AC adapter used

• Platform Size: 7.2 W x 6.7 H (in)/18.2 W x 17.0 H (cm)

• Resolution: 0 lb:0.1 oz, 0 lb:1/8 oz, 0.005 lb,

0.05 oz, 1/8 oz, 1 g

• Rechargeable battery: 4.8V 1800mAH (built-in)

• Power Adapter: 100-240VAC 50/60Hz input, 9V DC

(1000mA) output (included)

Note: Clean the scale before each use.

Note: In the following instructions, names of the

control buttons are shown in CAPS. Function

information that appears on the display is shown in

BOLD CAPS.

Power Adapter

Before using the external power adapter, make sure

that the printed voltage complies with the local

voltage.

Note: Use only an original CDN power adapter (AD-AC1110).

The use of other adapter is subject to approval by CDN.

1. Insert the adapter plug into the jack in the rear

of the scale.

2. To turn the scale on, press the POWER button

( ) as described in Section A: On/Off. The scale will

remain on until turned off.

Note: When the power adapter is plugged in, the auto-off

feature is disabled.

Charging the Battery

The icon ( ) and appear on LOW BATTERY bAtt

the display when battery status is low and needs

to be charged. The icon ( ) ashes LOW BATTERY

continuously while charging. The battery is built-in and

does not need to be replaced.

1. Insert the adapter plug into the jack on the back

of the scale. Allow the scale to charge for

5 hours. The scale will then operate continuously for

approximately 14 hours

Operating Instructions

Place the scale gently on a hard and at surface

and make sure it is steady before use to obtain

accurate measurements.

A. On/Off

A. Press the POWER button ( ) to turn on.

The display ashes all segments and then

returns to zero.

B. The STABILITY icon ( ) appears in the lower left

corner of the display when the weight is stable.

C. Press the POWER button ( ) to turn off.

B. Auto Off

The scale automatically turns off after 2 minutes of

inactivity.

Note: Auto-off is disabled when the AC adapter is used.

Model: SD1110X

ProAccurate®

Submersible Scale

11 pounds/5 kilograms/176 ounces

by pounds:ounces, ounces, fractional ounces and grams

C. Backlit Display

Press and hold the UNIT button for 3 seconds

to turn the backlit display on and off.

D. Unit Selection

Press the UNIT button to select the desired unit.

The display cycles through , , , , , g lb:oz lb:/oz lb oz

and ./oz

E. Tare

The tare function resets the scale display to zero

in order to measure only the weight of an item. It is

frequently used to subtract the weight of containers.

1. When the scale is on, place a container on

the platform.

2. Press the TARE button to reset the display

to zero.

3. Place the item into the container or directly on

the scale platform. The weight of only the last

item added will appear on the display.

4. Continue to repeat steps and 2. 3. to measure

the respective weights of additional items.

5. To clear the tare, remove all items from the

platform and press the TARE button. The display

is reset to zero.

F. Low/High Limit Alerts

The scale may be set to alert you when an item’s

weight is under or over a set limit.

1. Press and hold the TARE button for 3 seconds.

The scale beeps as and the zero weight LOW

appears on the display.

2. Place a weight equal to the low weight limit on

the platform and press the SET button. A beep

indicates that the low limit is set.

3. HIGH appears on the display. Add weight to the

platform until the weight is equal to desired

high weight limit. Press the SET button. A beep

indicates that the high limit is set.

4. Remove all items from the platform.

5. An alert will now sound if an item placed on

platform is over or under the set limits. LOW

or appears on the left side of the display HIGH

when these conditions exist.

6. To clear the Low/High limits, press both SET and

TARE buttons simultaneously.

G. Field Calibration

1. When scale is off, press and hold POWER button

( ) until the scale turns on. When all segments

are on, release the POWER button ( )

and press the UNIT button 3 times within one

second. The display shows , then , 11111 55555

and then the version number and checksum

appear before resetting to zero.

2. Making sure there is no load on the platform,

press the SET button to save the zero value.

3. Put a 5 kg calibration weight on the platform.

4. Press the SET button again to start the

auto-calibration. The scale shows 5000 g

and then before automatically turning off. CAL

The calibration is complete.

H. Battery Status

Battery status is low and needs Low Battery:

to be charged. See on Charging the Battery

page 1.

I. Error Messages

oL indicates an overload when the item being

measured exceeds the capacity of the scale.

Immediately remove the overweight item to avoid

causing permanent damage to your scale.

J. Programmable Modes

The scale has been pre-congured at the factory

and should not require conguration for use in most

applications. In the event that the factory settings

do not meet the requirements of your application,

the following describes the steps

to congure the scale.

1. Units

The scale has been pre-congured at the factory

for six units of measure. In the event that these

do not meet the requirements of your application,

the following describes the steps

to limit the number of unit choices available. The

sequence of units is , , , , lb:oz lb:/oz lb oz

/oz and .g

a. Press the POWER button ( ) to turn on.

b. Press and hold the SET button for 3 seconds.

When appears on the display, release the SEt

SET button to enter the conguration mode.

UNIT appears on the display.

c. With UNIT appearing on the display, press the

SET button to select lb/OZ (pounds/ounce)

units (11 lb @ 0.1 oz). Both the unit and its

status appear on the display.

d. Press the UNIT button to toggle between

ON (enabled) and OFF (disabled).

e. Press the SET button to conrm the status

and to select the next unit in the sequence.

f. Repeat steps d. and e. for each respective

unit. Upon conrming the status for , g

UNIT appears on the display.

g. Press the UNIT button three times.

END appears on the display.

h. Press the SET button to save the settings and

return to weighing mode.

2. Auto Off

The scale has been pre-congured at the factory

to automatically turn off after 120 seconds

(2 minutes) of inactivity. In the event that your

application requires longer shut-off times or none

at all, the following describes the steps

to congure this feature.

a. Press the POWER button ( ) to turn on.

b. Press and hold the SET button for 3 seconds.

When appears on the display, release the SEt

SET button to enter the conguration mode.

UNIT appears on the display.

c. With UNIT appearing on the display,

press the UNIT button. AOFF appears

on the display.

d. Press the SET button to begin selection of the

auto off time (in seconds). appears on the 120

display.

e. Press the UNIT button to cycle through the

selections: 120, , 180 240, or 300 OFF.

f. When the desired time is displayed, press the

SET button to conrm the selection. AOFF

appears on the display.

g. Press the UNIT button twice. END appears

on the display.

h. Press the SET button to save the settings and

return to weighing mode.

3. Gravity Compensation

The gravity compensation for your scale has

been pre-congured at the factory and should

not require changing in most locations. In the

event that the factory settings do not meet the

requirements of your location, contact CDN for

the value for your location. With GrAu enabled,

the scale will use the default value of 9.797. If

the GrAu is disabled, the scale will use the value

obtained from CDN and entered by the operator

for the gravity compensation.

a. Enabling/Disabling Gravity Compensation

1.) Press the POWER button ( ) to turn on.

2.) Press and hold the SET button for 3

seconds. When SEt appears on the

display, release the SET button to enter

the conguration mode. appears on UNIT

the display.

3.) With UNIT appearing on the display, press

the UNIT button twice. GrAu appears on

the display.

4.) With GrAu appearing on the display, press

the SET button again to enable the gravity

compensation. appears on the display.ON

5.) Press the UNIT button to toggle between

ON (enabled) and OFF (disabled).

6.) Press the UNIT button again to disable the

gravity compensation. appears on the OFF

display.

7.) Press the SET button to conrm the

selection. appears on the display.GrAu

8.) Press the UNIT button. appears on END

the display.

9.) Press the SET button to save the settings

and return to weighing mode.

b. Gravity Compensation Value Editing

Contact CDN for the value to enter for your

location.

Note: Gravity compensation must be disabled for

this value to take effect.

1.) Press and hold the UNIT button and press

the POWER button ( ) to turn on the scale

and enter the value editing mode. 9.797

(or the current value) appears on the

display.

2.) Press the TARE button to choose a

number from to enter the desired 0 to 9

gravity value.

3.) Press the UNIT button to move to the next

digit to the right.

4.) Repeat steps 2.) and for the 3.)

remaining digits.

5.) Press the SET button to conrm the

entered gravity value and return the scale

to the normal operating mode.

Note: Clean the scale platform before each use.

Note: Replacement AC adapter, removable platform and

5 kg calibration weight available.

Usage Guidelines

• Scales are precision instruments and must be

handled with extreme care.

• Battery technology works best at room temperature.

• Place the scale gently on a hard and at surface and

make sure it is steady before use.

• The maximum capacity of the scale is 11 lb/5 kg,

which is the capacity before using the tare function.

• Do not place overweight items on the scale.

• Store the scale in a position that keeps it free from

any load bearing weight. Storing the scale with

pressure on the load cells can distort the weight

measurements over time.

• Hold the scale from the bottom when moving.

Care of Your Product

• — protected from water up to 3 feet for IP67

30 minutes, completely protected against dust.

• Wipe clean with a damp cloth.

• Store the scale at room temperature between

32 to 104°F/0 to 40°C.

Note: This device could be sensitive to electrostatic

discharge. If electrostatic discharge or malfunctioning

occurs, please re-install the battery to reset this unit.

Product specificaties

Merk:	CDN
Categorie:	Keukenweegschaal
Model:	SD1110X

Heb je hulp nodig?

Als je hulp nodig hebt met CDN SD1110X stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Keukenweegschaal CDN

CDN SD2210X Handleiding

26 Juni 2023

CDN SD1110X Handleiding

26 Juni 2023

CDN SD1104 Handleiding

26 Juni 2023

CDN SD5502 Handleiding

26 Juni 2023

Handleiding Keukenweegschaal

Nieuwste handleidingen voor Keukenweegschaal

Smeg FS0104 Handleiding

21 November 2024

Salter 1074 Handleiding

20 November 2024

Salter 1064 WHDR Handleiding

20 November 2024

Taylor TE22OS Handleiding

18 November 2024

Cardinal Detecto AP-6 Handleiding

17 November 2024

Livoo DOM431 Handleiding

15 November 2024

Scarlett SC-KS57P82 Handleiding

8 November 2024

Scarlett SC-KS57P78 Handleiding

8 November 2024

Primo SCK3 Handleiding

5 November 2024

Hyundai KVE 927 Handleiding

21 September 2024