Byron MP001 Handleiding

Byron Deurbel MP001

Lees hieronder de πŸ“– handleiding in het Nederlandse voor Byron MP001 (4 pagina's) in de categorie Deurbel. Deze handleiding was nuttig voor 66 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
MP3 Downloadable
Wire Free Chime Kit
β„’41: Press the Bell Push to
confirm the setup
2: The Chime will play the
melody and the alert light will
flash.
4
2
1: Place a small flat screwdriver
into the locking clip on the
base of the Bell Push.
2: Gently twist.
3: The backing plate will unclip.
1
β„’
1: Push Button 6: Portable Chime
2: Melody Selector 7: Speaker
3: Bell Push Battery 8: Volume Control
4: Signal Sent LED 9: LED Alert
5: USB Lead 10: USB Input
MP001
β„’
:3
1:
4: 10:
8:
9:
5:
6:
2:
31: Remove the battery cover.
2: Insert 3 X 1.5V Size β€˜AA’
batteries (Not Supplied).
3: Make sure the
Positive/Negative terminals
match the internal markings
4: switch the Chime ON
5: Replace the battery cover.
1: Insert CR2032 battery
(Supplied) into the battery
holder.
2: Make sure the positive side
is facing upwards.
3: Replace back plate.
Warning: Make sure that the batteries are
replaced correctly to avoid battery failure.
Only replace with same or equivalent type.
3
Downloading MP3 Melody:
Functions:
To select the Chime Volume
level, press the β€˜+’ button
increase the volume and β€˜-’
button to decrease the volume.
To select a melody for the Door Chime
1: Select between preprogrammed (IN) or
downloaded MP3 melodies (MP3).
2: Press the arrows on the door
chime to select the next melody
3: The chime will play the newly selected
melody
4: Press the centre button to confirm
Or press arrows to select the next
melody.
1: Connect the chime to the
USB port of a computer using
the USB lead (supplied ).
PC Only
2: The Chime will appear as a USB
storage device, install and run MP3
Editor.exe file on your computer.
MP3 Music
Look in:
Open
MP3 File(*.mp3)
File Name:
Files of Type:
Open
Cancel
Melody File 1
Melody File 2
Melody File 3
Melody File 4
3: Select the open file icon ,
highlight the required MP3 file on
your PC and click Open.
5: Edit the file length by inputting the required start and end times.
Use the Play/Pause button to listen to the mp3 file, recommended file
length is between 8-10sec.
5: Press the scissors icon to Cut and save the MP3 file, the
recommended file length is approximately long. 8-10 seconds
Melody File 1 Melody File 2 Melody File 3
Back Search Folders
E:\Address
PC & Mac
6: Drag and drop the edited file onto the MP3 Chime, the file will be
saved on to the MP3 chimes internal memory.
00:00.0 / 00:00.0
00Start Time
End Time
00
00 00 0
0:
:
.
.Reset
Rewind Fast
Forward
Play Volume
Stop
Press to Cut
4: Highlight the MP3 file in the tunes list and press PLAY.
Video Tutorial:
View or video tutorial saved on the MP3 chime or via our
YouTube channel.
http://www.youtube.com/user/CHByron
Installation Guide:
Portable Door Chime: MP001/HB702
Power: 3 x β€˜AA’/LR6 1.5V Batteries
(Not supplied)
Range: 100 Metres
Indoor Use Only
Bell Push: MPT
Power: 1 x 23A 12V DC Battery
(Included)
IP44 Weather Resistant
Specification
Range Guide
433.92MHz
R&TTE
APPROVED
CH Byron Electrical United Kingdom. www.chbyron.com
A
B
DK
FIN
F
D
GR
LT
IRL
I
L
NL
P
E
S
UK
BG
CZ
EST
H
IS
LV
M
N
SK
SLO
CH
PL
RO
Project Manager
Mr G Hunter
GB: CH Byron
Byron House, Sherwood Rd
Astonfields, Bromsgrove
B60 3DR
UK
support@chbyron.com
9-5 Mon-Fri, Local call charges apply
V1.0
Tel: 0845 2301231 (UK)
www.chbyron.com
Avoid locating the Bell Push/Chime on or directly
near metallic surfaces as this may reduce the
operation range.
UPVC Door Frames:
When locating the bell push onto a UPVC door,
always check the operating performance before final
installation, internal metal frame may affect
performance.
Tip: Try adjusting the location of the Bell Push to the Left/Right
or place on external wall.
Installation Guide: Bell Push
Installation Guide: Chime
Place the door Chime within the operating range,
transmission of the wire free signal through
Walls, Doors and Ceilings etc, may reduce the operating
range. Chime unit for INDOOR use only.
Diagram for illustration purposes only
1
2
β€˜CLICK’
1: Using back plate as a
template.
2: Making sure UP arrow
points UP.
2: Mark and drill holes.
3: Insert wall plugs and attach
to wall using screws
provided.
4: Clip the Bell Push on to the
back plate making sure the
Bell Push β€˜Clicks’ in to
place.
Tip: The Bell Push can be
installed using a suitable
double sided adhesive tab or
tape when drilling is not
sutiable.
3
User Hints:
In case of the door chime does not sound, please check the
followings:
a) Flat batteries in either Push Button or Door Chime.
b) Wrong battery polarity in either Push Button or Door Chime.
c) For Plug-in Door Chimes make sure the socket is switched on.
d) Bell Push and Door Chime are not paired together, see setup
guide.
e) Materials in between the Bell Push & Chime will reduce the
operating range, move the Door Chime closer to the Bell Push
f) Wire free devices can be affected by external sources e.g. wire
free home alarms or power transformers/adapter
Chime Unit
1: Remove old Batteries.
2: Insert new batteries, 3 X 1.5V
size β€˜AA’.
3: Make sure β€˜+/-’ match the
internal markings.
4: Test Chime Kit.
Changing Batteries:
Bell Push:
1: Remove back plate from the
Bell Push.
2: Remove old battery
3: Replace with new β€˜23A’ 12V
battery.
4: Insert into holder making sure
β€˜+/-’ match the internal
marking
5: Test Chime Kit.
Always dispose of old batteries in an
environmentally friendly way.
Type R2 Device - device where the sound output is created by the initial
operation of the control and where the period of sound output continues
for the designed duration irrespective of condition of the control.
IMPORTANT:
There are no serviceable parts, do not repair. The appliance is not to be used by children or persons with
reduced physical, sensory or mental capabilities, or lack of experience and knowledge,unless they have been
given supervision or instruction. Children should be supervised to ensure that they do not play with the
appliance.
Address Code:
The MP3 Door Chime, comes preset to a default address code, this
code may need to be changed if the chime rings due to a
neighbouring door chime or similar wire free product.
1: Select a new address code in the bell
push, by randomly moving the white
dip-switch’s.
2: Copy the new address onto the
chimes dip-switch’s. Located in the
battery compartment of the chime.
3: Test the chime kit by pressing the
bell push.
1 65432
ON Dip
1 65432
ON Dip
e.g.


Product specificaties

Merk: Byron
Categorie: Deurbel
Model: MP001

Heb je hulp nodig?

Als je hulp nodig hebt met Byron MP001 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Deurbel Byron

Handleiding Deurbel

Nieuwste handleidingen voor Deurbel