Brother P-Touch PT-H100 Handleiding

Brother Labelprinter P-Touch PT-H100

Lees hieronder de 📖 handleiding in het Nederlandse voor Brother P-Touch PT-H100 (2 pagina's) in de categorie Labelprinter. Deze handleiding was nuttig voor 55 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

ELECTRONIC LABELING SYSTEM

Follow these guidelines to avoid the risk of fire, burns, injury,

rupture, overheating, abnormal odor or smoke.

• Do not use the P-touch labeler in places of high humidity such as bathrooms.

• Do not allow the P-touch labeler/batteries to get wet, for example, by handling them

with wet hands or spilling beverages on to them.

• Since loss of eyesight may result when leaked fluid from batteries gets into your eyes,

immediately rinse your eyes with a large amount of clean water, and then seek

medical attention.

• Do not disassemble or modify the P-touch labeler/batteries.

• Do not allow a metal object to contact both the plus and minus ends of a battery.

• Do not use sharp objects, such as tweezers or a metallic pen, to change the batteries.

• Do not throw the batteries into fire or expose to heat.

• Remove batteries immediately and stop using the P-touch labeler if you notice

abnormal odor, heat, discoloration, deformation or anything unusual while using or

storing it.

• Do not use a damaged or leaking battery as the fluid may get on your hands.

• Do not use a deformed or leaking battery or one whose label is damaged. There is a

possibility of generating heat.

Follow these guidelines to avoid personal injury, liquid

leakage, burns or heat.

• When the P-touch labeler is not being used, store it out of the reach of children. In

addition, do not allow children to put the P-touch labeler parts or labels in their

mouths. If any object has been swallowed, seek medical attention.

• Do not touch metal parts around the print head immediately after printing.

• Do not touch the cutter blade.

• If leaked fluid from batteries gets on your skin or clothes, immediately rinse them with

clean water.

• Remove the batteries if you do not intend to use the P-touch labeler.

• Do not use a battery other than that specified. Do not use combinations of old and

new batteries or combinations of different types, different charging levels, different

manufacturers or different models. Do not insert a battery with its plus and minus

ends reversed.

• Do not drop or hit the P-touch labeler.

• Do not press on the LCD display.

• Do not put your finger inside the P-touch labeler when you close the cassette cover.

• Before using Ni-MH rechargeable batteries, carefully read the instructions for the

batteries and battery charger, and be sure to use them correctly.

• When using Ni-MH rechargeable batteries, charge the batteries with a specialized

battery charger before using the batteries.

• Depending on the location, material, and environmental conditions, the label may

unpeel or become irremovable, the color of the label may change or be transferred

to other objects. Before applying the label, check the environmental conditions and

the material.

• Do not use the P-touch labeler in any way or for any purpose not described in this

guide. Doing so may result in accidents or damage the P-touch labeler.

• Use only Brother TZe tapes with the P-touch labeler. Do not use tapes that do not

have the mark.

• Only use a soft, dry cloth to clean the labeler; never use alcohol or other organic

solvents.

• Use a soft wipe to clean the print head; never touch the print head.

• Do not put any foreign objects into the tape exit slot or battery compartment, etc.

• Do not place the P-touch labeler/batteries in direct sunlight or rain, near heaters or

other hot appliances, in any location exposed to extremely high or low temperatures

(e.g., on the dashboard or in the back of your car) or high humidity, or in dusty

locations.

• Do not apply excessive pressure to the cutter lever.

• Do not try to print if the cassette is empty; it will damage the print head.

• Do not pull the tape while printing or feeding; it will damage the tape and the P-touch

labeler.

• Any data stored in memory will be lost due to failure or repair of the P-touch labeler,

or if the battery expires.

• The P-touch labeler is not equipped with a charging feature for rechargeable

batteries.

• The length of the printed label may differ from the displayed label length.

• A protective clear plastic sticker is placed over the display during manufacturing and

shipping. This sticker should be removed prior to use.

• When power is disconnected for more than three minutes, all text, format settings and

any text files stored in the memory will be cleared.

Safety Precautions

Indicates a potentially hazardous

situation which, if not avoided,

could result in serious injuries.

WARNING

Indicates a potentially hazardous

situation which, if not avoided,

may result in minor or moderate

injuries.

General Precautions

CAUTION

FCC NOTICE

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Consult the dealer or an experienced radio/TV technician for help.

Important

• Changes or modifications not expressly approved by Brother Industries,

Ltd. could void the user’s authority to operate the equipment.

Power Supply and Tape Cassette

Open the cassette cover by pressing the

above indicated area at the top end of the

machine.

If a tape cassette is already installed, remove it by

pulling it straight up. Also, if batteries are already

installed, remove them.

• Make sure that the power is turned off when

replacing batteries or tape cassettes.

Insert six new AAA alkaline batteries

(LR03) or fully charged Ni-MH batteries

(HR03), making sure that their poles

point in the correct directions.

Users of alkaline batteries:

Always replace all six batteries at the

same time with brand new ones.

Users of Ni-MH batteries:

Always replace all six batteries at the

same time with fully charged ones.

NOTE

Visit us at http://solutions.brother.com/ for the latest

information about the recommended batteries.

Insert a tape cassette, making sure that

it snaps into place.

• Make sure that the end of the tape feeds under

the tape guides.

• Use only Brother TZe tapes with this machine.

Securely close the cassette cover, making

sure that it snaps into place.

Tape cutter

lever

Cassette

cover

2Print head

Toothed

wheel

Cutter’s

edge

End of tape

Tape

exit slot

Tape guide

NOTE

• The LCD shows one row of 12 characters; however, the text that

you enter can be up to 80 characters in length.

• While selecting the settings, press the Space key to go back to

the default item.

LCD Display & Keyboard

14 23

1. Size

2. Cursor

3. Caps

4. Underline/Frame

5. Width

6. Style

7. Label Length

If a specific label length has been

selected, also appears.

8. Guidance (left, right)

9. Power key

10. Cursor key : Right

11. Cursor key : Left

12. Backspace key

13. Size key

14. Style key

15. Character keys

16. Caps key

17. Symbol key

18. Menu key

19. Clear key

20. Print key

21. Enter key

22. Auto Designs key

23. Frame key

24. Accent key

25. Space key

• The print preview is a generated image of the label, and may

differ from the actual label when printed.

• Label length shown on LCD may slightly differ from the actual

label length when printed.

1Start your machine.

Supply power by using six AAA batteries, and then press

2Set the language.

3Set the unit of measurement.

The default setting is [inch].

NOTE

• The machine automatically turns off if no keys are pressed within

five minutes.

• To cancel any operation, press .

Initial Settings

/ [Language] /

[English/Español/Français/Hrvatski/Italiano/Magyar/

Nederlands/Norsk/Polski/Português/Portug. (BR)/

Română/Slovenski/Slovenský/Suomi/Svenska/Türkçe/

Čeština/Dansk/Deutsch] .

/ [Unit]

/ [inch/mm] .

Troubleshooting

XError message XWhat to do when...

Message Cause/Remedy

Low Battery!

The batteries are weak.

If using AAA alkaline batteries: Replace them with new

ones.

If using Ni-MH batteries: Charge them fully.

Battery Dead The installed batteries are running low.

Invalid! An invalid number was entered as the label length.

(This is not displayed in Auto Designs function.)

No Text!

• You tried to print a text file when there is no data

stored in the memory.

• is pressed when no text is entered.

• You tried to select Text Preview or Cable Label when

no text is entered.

• was pressed when no text was entered while

using the DECO MODE or Auto Designs function.

Line Limit!

• You tried to enter a 3rd line by pressing .

• You tried to print or preview two lines of text while

0.13" (3.5mm) or 0.23" (6 mm) tape is installed. Install

tape of a larger size.

No Cassette! You tried to print a label when there is no cassette

installed.

Cutter Error The tape cutter lever was used during the printing

process.

Text Full!

The maximum number of characters (80 characters*)

have already been entered.

*50 characters - for Auto Designs function and DECO

MODE

Text Limit!

With the DECO MODE function:

Since the number of entered characters exceeds the

label length, reduce the text.

All other functions:

Since the number of entered characters exceeds the

label length, reduce the text, or select [Auto] as the

label length.

No Frame OK?

Printing on 0.13" (3.5mm) tape with invalid Frame

setting ON. (Select to print with no Frame,

to cancel.)

OK to Feed? Feeding tape after printing when [Chain Print] is

selected. Refer to “Setting Margin”.

Insert 0.47" Only 0.47"(12mm) tapes are available for use with

DECO MODE function.

Wrong Tape! Use a tape cassette with the mark.

Message Cause/Remedy

Problem Solution

The display stays blank

after you have turned on

the machine.

• Check that the batteries are correctly

inserted.

• If the batteries are weak, replace them.

When the label is printed

out, the margin(space) is

too large on both sides of

the text.

• See “Setting Margin” in this users guide

and select [Half] or [Narrow] to have

smaller margins for your label.

The machine does not

print, or the printed

characters are not formed

properly.

• Check that the tape cassette has been

inserted correctly.

• If the tape cassette is empty, replace it.

• Check the cassette cover is properly

closed.

The setting has cleared

on its own.

• The batteries may be weak. Replace

them.

• When power is disconnected for more

than three minutes, all text & formats in

the display will be lost. Language and Unit

settings will also be cleared.

A blank horizontal line

appears through the

printed label.

• There maybe some dust on the print

head. Remove the tape cassette and use

a dry cotton swab to gently wipe the print

head with an up-and-down motion.

The machine has “locked

up” (i.e., nothing happens

when a key is pressed,

even though the machine

is on.)

• Refer to “Resetting the P-touch”.

The power turns off when

you try to print.

• The batteries may be weak. Replace

them.

• Check that the batteries are correctly

inserted.

The tape does not feed

properly or the tape gets

stuck inside the machine.

• Check that the end of the tape feeds

under the tape guides.

• The cutter lever is used while printing. Do

not touch the cutter lever during printing.

All text and format

settings need to be

cleared to create a new

label.

• Press and select [Text&Format].

The LCD is set to an

incorrect language. • Refer to “Initial Settings”.

Problem Solution

BASIC USAGE

XSwitching Upper Case/Lower Case

Upper case ( ON) Lower case ( OFF)

XMaking Two Lines of Text

To make two lines of text, do one of following:

Enter the text for the first line and then press for the

second line.

Move the cursor to where the second line starts and press

Use either 0.35" (9mm) or 0.47" (12mm) wide tape for two line text.

NOTE

Do not press after the second line; otherwise the “Line Limit!”

error message will appear.

XTo Clear

By pressing , the letters will be deleted one by one.

To delete all text and settings :

To delete text only :

XEntering Accented Characters

• To cancel the current operation, press .

• The order of accented characters differs depending on the

selected LCD language.

XChanging Label Length

NOTE

• After the label is printed, cut along the printed dots (:) with

scissors so that the label length matches the machine setting.

• If a specific label length has been selected, also appears in

the LCD.

XPreview

You can preview the text before printing.

Only the text can be previewed, not the size, font or any

additional features.

XFeeding (Tape Feed)

XPrinting

• If you need only 1 copy of the label, press without

selecting the number of copies.

• The number of copies can also be specified by pressing a

number key.

• To prevent damage to the tape, do not touch the cutter lever

while the message "Printing..." or "Feeding..." is displayed.

• To cut off the label, push in the tape cutter lever on the upper-

right corner of the machine.

• Peel the printed label from the backing and apply the label.

• You can print up to 9 copies of each label.

XSetting Margin

[Full]/[Half]/[Narrow]

For leaving equal margins on both sides of the text.

[Chain Print]

For creating a label containing text in various styles.

1. Enter text.

2. Press , then [Copies: ] appears.

3. Press / or enter number with number keys to

select the number of copies.

4. Press . Printing will start, and then the message "OK

to Feed?" appears.

5. Press to enter more text.

6. Clear the text, enter the text for the next label, and then

press .

7. When the message "OK to Feed?" appears after the last

label is printed, press .

8. After the tape is fed, press the cutter lever to cut off the

chain of labels.

NOTE

• When [Half] or [Narrow] is set, the displayed label length is the

length from the printed dots ( ) to the end of the label.

• To print more than 1 copy of a label with minimum margin, set

the margin to [Narrow].

• When [Chain Print] is set, feed the tape before using the cutter

otherwise a part of the text may be cut off. Also, cut along the

printed dots ( ) with scissors so the text is centered in the label.

*Feed the tape before using the cutter.

• Do not pull the tape since this may damage the tape cassette.

You can save up to 9 labels and recall them for printing at a later

date. A maximum of 80 characters can be saved per file, a

maximum total of 720 characters for the total memory. You can

also edit and overwrite the stored label.

XPrint

XSave

XOpen

NOTE

If you try to store a label when there is already a label stored to that

number, a message “Overwrite?” will appear. Press to save

your new label. Press to cancel.

If the cutter blade becomes dull after repetitive use and the tape cannot

be cut cleanly, replace with a new cutter (stock no. TC-4). You may

obtain this item from an authorized Brother reseller.

XReplacing the Cutter Unit

1. Pull out the two sections of the cutter unit (green) in the

direction of the arrows shown in the illustration.

2. Install a new cutter unit. Push it in until it snaps into place.

You can reset the P-touch labeler when you want to initialize the

settings, or in the event the P-touch labeler is not working properly.

Turn off the P-touch labeler, hold down and

and then press to turn the P-touch back on.

2Release and .

The P-touch labeler turns on with the internal memory reset.

NOTE

All text, settings and stored files are cleared.

Entering Text

LCD display Label image

/ [Text&Format]

/ [Text Only]

- / /

A a

C D c d

E e

G I g i

K L k l

N R n r

O o

S T s t

U u

Y Z y z

/ [Label Length]

/ [Auto/1.2"-12.0" (30-300 mm)]

Printing Labels

/ [Preview]

/ [Feed]

[Copies: 1] / / -

/ [Margin]

/ [Full/Half/Narrow/Chain Print]

LCD display Label image

Full

Half

Narrow

0.16"0.16"

ABC ABC

0.47" 0.47"

(4 mm)

(25 mm) (12 mm)

ABC

Full Half Narrow

2.7"

(67 mm)

ABC

1.6"

(41 mm)

ABC

(25 mm)

ABC

Saving Label Files

/ [File] / [Print]

[Copies: ] / -

/ [File] / [Save]

/ [File] / [Open]

Accessories

Tape Cassettes: See the included “Supplies and

Accessories Guide”.

Cutter Unit: TC-4 (replacement)

Do not touch the cutter blade directly with your fingers.

Resetting the P-touch

Declaration of Conformity

(Europe/Turkey only)

We, BROTHER INDUSTRIES, LTD

15-1, Naeshiro-cho, Mizuho-ku,

Nagoya, 467-8561, Japan

declare that this product is in compliance with the essential

requirements and other relevant provisions of Directives

2004/108/EC.

The Declaration of Conformity (DoC) is on our Web site.

Please go to http://solutions.brother.com -> choose region

(eg. Europe) -> choose country -> choose your model ->

choose “Manuals”-> choose Declaration of Conformity

(*Select Language when required).

USING TEMPLATES

The designed labels shown below are preset in the machine.

Using these templates, you can create decorative labels easily by

inputting text.

Example:

If [Surprise!] is selected, a frame, style and pictographs are selected randomly.

This function allows you to create unique labels by using built-in templates.

Example:

NOTE

• Depending on the format you have selected, the entire contents of your text may

not be printed. For example, if you selected a fixed Label Length and the text is too

long, the "Text Limit!" error message will appear. (Only for DECO MODE function)

• The template designs cannot be edited.

• Only the highlighted symbols in “Symbol Key” can be used in DECO MODE.

• To clear all text, press , and “Clear?” appears. Press to clear. Press

to cancel.

• When you access DECO MODE or Auto Designs, your most recently printed

DECO MODE or Auto Designs text and label length will be recalled.

• Press to return to the previous step.

• To exit DECO MODE or Auto Designs and return to the text input screen, press

/ to select [Cancel], and then press when [Print] is displayed.

• The DECO MODE features are only available when using 0.47" (12mm) tape

cassettes.

• The maximum label length is 7.8" (200mm) for the DECO MODE.

• When [Surprise!] is selected in the Auto Designs function, label length will not be

displayed in the text input screen.

• When [Auto] is selected for “Label Length”, the label will automatically adjust to the

correct length for the text.

• Press to return to the [Auto] setting for “Label Length” mode.

Press to select the frame design.

NOTE

Frames cannot be printed on 0.13" (3.5mm) tape.

NOTE

With the Cable Label function, [Auto] is automatically selected for

the label length and [Full] for the margins.

USEFUL FUNCTION KEYS

1Press or or + to select the

settings to enter the text.

2Press / to select the settings.

Press to select various symbols.

To enter Basic symbols :

Only the highlighted symbols can be used in DECO MODE.

To enter Pictograph symbols :

The selected symbol is displayed as "A1" in the text input screen.

For example, a car is displayed as in the screen.

To print all pictographs :

NOTE

Press to return to the previous step.

Auto Designs

[★ ★Category ] / [Pets]

[★Input text★] Rusty's Food [Print]

Congrats Sports

People Fashion

Pets Flower

Kitchen Space

Business Surprise!

DECO MODE

/ [Deco mode]

[Design X] (X:1-12)

[Input Text] ABCDEF

[Label Length] / [Auto/1.2"-7.8"(30-200mm)]

[Print]

1 7

2 8

3 9

4 10

5 11

6 12

Frame Key

/ Select a frame

4 7

5 8

369

Cable Label

This function allows you to create cable labels

as below with 2 lines of text wrapping around

cable. We recommend using Brother Flexible

ID tape when wrapping.

Refer to the insertion sheet included with

Flexible ID tape about the recommended

conditions for use.

[Input text] ABC 159 / [Cable]

[Print OK?] [Copies: 1] / / -

ABC

159

ABC

159

Text Keys / / +

or or + / Select an item

Size Large

Medium

Small

Style Normal

Bold

Outline

Shadow

Italic

I+Bold

I+Outline

I+Shadow

Vertical

Width

Normal

× 2

× 1/2

Short Cut Keys

Width

Label Length

Margin

File

Cable

Deco mode

Preview

Feed

Unit

Language

Symbol Key

/ [Basic] / Choose a symbol

/ [Pictograph] / Select category

/ Choose a symbol

1 2 3 4 5 6 7 8 9

/ [Print List] [Print OK?]

With your PT-H100, you can create labels for multiple

applications. Select from the many frames, character sizes and

styles to design beautiful custom labels. In addition, the variety

of tape cassette available allows you to print labels with different

widths and exciting colors.

Read this manual carefully before you begin and keep the

manual in a handy place for future reference.

Printed in China

LAA204001

English

EnglishEnglish

Español

EspañolEspañol

User’s Guide

1Visit us at http://solutions.brother.com/ for the latest

information about the recommended batteries.

Specifications

Dimensions:

(W x D x H)

Approx. 4.4" × 8.2" × 2.4"

(Approx.110(W) × 208(D) × 59(H)mm)

Weight: Approx. 0.9 lb. (Approx. 390 g)

(without batteries and tape cassette)

Power supply: Six AAA alkaline batteries (LR03)

Six AAA Ni-MH batteries (HR03)*1

Tape cassette: Brother TZe tape (width)

0.13" (3.5mm), 0.23" (6mm),

0.35" (9mm), 0.47" (12mm)

Should you encounter any problems with your product,

please do not return your product to the store!

After referring to the User's guide, if you still need

assistance, call Brother Customer Service at:

Voice: 1-877-BROTHER

Web: www.brother-usa.com

Fax: 1-901-379-1210

If you need to locate a service center, please call

1-877-BROTHER or visit us at www.brother-usa.com

Product specificaties

Merk:	Brother
Categorie:	Labelprinter
Model:	P-Touch PT-H100
Kleur van het product:	Grey, White
Gewicht:	408.2 g
Breedte:	109.2 mm
Diepte:	58.42 mm
Hoogte:	208.3 mm
Kleur:	Nee
Beeldscherm:	LCD
Ethernet LAN:	Nee
Ondersteund aantal accu's/batterijen:	6
Maximale resolutie:	180 x 180 DPI
Printkleuren:	Zwart
Printtechnologie:	Thermo transfer
Netwerkgereed:	Nee
Navigatietoets:	Ja
PC connected:	Nee
Printsnelheid (metrisch):	20 mm/sec
Maximale print hoogte:	9 mm
Wifi:	Nee
Batterijen inbegrepen:	Nee
Batterijtechnologie:	Alkaline
Type batterij:	AAA
Aantal afdrukbare regels:	2
Labelgeheugen:	9 etikett(en)
Soort tape:	TZe
Aantal letterstijlen:	9
Aantal lettertypes:	1
Verticaal printen:	Ja