Broan 273003 Handleiding

Broan Afzuigkap 273003

Lees hieronder de 📖 handleiding in het Nederlandse voor Broan 273003 (24 pagina's) in de categorie Afzuigkap. Deze handleiding was nuttig voor 77 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/24

MODELS 2730 & 2736 ECLIPSE

DOWNDRAFT BLOWER SYSTEM

READ AND SAVE THESE INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY

TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer.

If you have questions, contact the manufacturer at the address

or telephone number in the warranty.

2. Before servicing or cleaning unit, switch power off at service panel

and lock the service disconnecting means to prevent power from

being switched on accidentally. When the service disconnecting

means cannot be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a qualified

person(s) in accordance with all applicable codes and standards,

including fire-rated construction codes and standards.

4. Sufficient air is needed for proper combustion and exhausting

of gases through the flue (chimney) of fuel burning equipment

to prevent backdrafting. Follow the heating equipment manufac-

turer’s guideline and safety standards such as those published

by the National Fire Protection Association (NFPA), and the

American Society for Heating, Refrigeration and Air Conditioning

Engineers (ASHRAE), and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not damage electri-

cal wiring and other hidden utilities.

6. Do not use this range hood with an additional speed control

device.

7. Ducted fans must always be vented to the outdoors.

8. To reduce the risk of fire, use only metal ductwork.

9. Do not install this product with the activating switch directly behind

a burner or element. Minimum distance between the switch and

the edge of the burner should be 4 inches.

10. Loose-fitting or hanging clothing should never be worn when

operating this appliance. They may be ignited by burners/ele-

ments on cooktop.

11. Children should not be left alone or unattended in the area where

this appliance is in use.

12. This unit must be grounded.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

1. Never leave surface units unattended at high settings. Boilovers

cause smoking and greasy spillovers that may ignite. Heat oils

slowly on low or medium settings.

2. Always turn hood ON when cooking at high heat or when cooking

flaming foods.

3. Clean ventilating fans frequently. Grease should not be allowed

to accumulate on fan or filter.

4. Use proper pan size. Always use cookware appropriate for the

size of the surface element.

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT

OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWINGa:

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet,

or metal tray, then turn off the burner. BE CAREFUL TO

PREVENT BURNS. If the flames do not go out immediately,

EVACUATE AND CALL THE FIRE DEPARTMENT.

WARNING

2. NEVER PICK UP A FLAMING PAN - You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels - a

violent steam explosion will result.

4. Use an extinguisher ONLY if:

A. You know you have a Class ABC extinguisher, and you

already know how to operate it.

B. The fire is small and contained in the area where it

started.

C. The fire department is being called.

D. You can fight the fire with your back to an exit.

a Based on “Kitchen Firesafety Tips” published by NFPA.

CAUTION

1. For indoor use only.

2. For general ventilating use only. Do not use to exhaust hazard-

ous or explosive materials and vapors.

To avoid motor bearing damage and noisy and/or unbalanced

impellers, keep drywall spray, construction dust, etc. off power unit.

4. Clean filters and grease-laden surfaces frequently.

5. Do not repair or replace any part of this appliance unless

specifically recommended in this manual. All other servicing

should be done by a qualified technician.

6. Please read specification label on product for further informa-

tion and requirements.

INSTALLER: Save this manual for Electrical Inspector and Homeowner to use.

HOMEOWNER: Use and Care Information on Page 5.

INTENDED FOR DOMESTIC COOKING ONLY

GROUNDING INSTRUCTIONS

WARNING - This appliance must be grounded. In the event of an

electrical short-circuit, grounding reduces the risk of the electric

shock by providing an escape wire for the electric current. This

appliance is equipped with a cord having a grounding wire with

a grounding plug. The plug must be plugged into an outlet that

is properly installed and grounded.

WARNING - Improper grounding can result in a risk of electric shock.

Consult a qualified electrician if the grounding instructions are

not completely understood, or if doubt exists as to whether the

appliance is properly grounded.

Do not use an extension cord. If the power supply cord is too short,

have a qualified electrician install an outlet near the appliance.

RIGHT

DISCHARGE

DOWN

DISCHARGE

(as shipped)

LEFT

DISCHARGE

EQUALS 6 FT. OF

STRAIGHT DUCT

6" ROUND

ELBOW

3-1/4" X 10"

TO 6" RD.

TRANSITION

3-1/4" X 10"

90O ELBOW

EQUALS 8

FT. OF

STRAIGHT DUCT

EQUALS 2

FT. OF

STRAIGHT DUCT

PLAN THE WIRINg

1. The downdraft blower system draws 4 AMPS and requires a

120 VAC, 60 Hz circuit.

2. The unit has a 2 ft. long power cord with a 3-pronged plug.

Plan to provide a grounded outlet in a location which will allow

the unit’s power cord to reach. (Note: If the Model 2730 is be-

ing installed in a 30" wide cabinet or the Model 2736 is being

installed in a 36" wide cabinet, the outlet cannot be located

on the back wall of cabinet.) Outlet may also be wall-mounted,

with access hole in cabinet.

SPECIFICATIONS

VOLTS AMPS CFM DUCT

4.0 500 3-1/4 X 10120

TAKE MEASUREMENTS

1. Refer to the cooktop installation instructions for dimensions of

cooktop, countertop cut-out, and cabinet requirements. The

Model 2730 will fit in most 30" wide cabinets and the Model

2736 will fit in most 36" wide cabinets. However, it is recom-

mended that oversized cabinets be used for easier installation.

2. Cooktop depth can vary greatly from one to another. This may

cause the fit of these two appliances to be rather tight.

Pay special attention to the areas of potential interference high-

lighted above. A countertop with (A) a raised lip and/or (B) a

backsplash may not allow enough flat countertop for a proper

installation. Note that 2" of flat countertop is required behind

cooktop and that 1-3/4" is necessary between the back edge of

the cooktop and the inside of cabinet back.

PLAN THE DUCTWORK

1. This downdraft blower system is designed for use with 3-1/4" x

10" ductwork (can be transitioned to 6" round). Three different

discharge directions are available with side-to-side adjustment

for accurate alignment of ductwork.

2. For best performance: Choose the ducting option which al-

lows the shortest length of ductwork and a minimum number

of elbows and transitions. Check location of floor joists, wall

studs, electrical wiring or plumbing for possible interference.

NOTE: The unit is shipped with the 3-1/4" x 10" discharge

facing DOWN. See “CHANGING BLOWER DIRECTION” on

page 3, if necessary.

3. The system will operate most efficiently when the ductwork

does not exceed 40 feet of equivalent duct. The chart, above,

shows equivalent feet of elbows and transitions. The number

of feet of straight duct plus the equivalent feet of transitions

and/or elbows to be used should equal 40 feet or less.

NOTE: The equivalent feet of various roof and wall caps has

been taken into consideration. Do not include them in this

calculation.

AIR

VENT

COUNTER

TOP

BLOWER

BOX

CHIMNEY TOP

3-1/4" X 10"

DUCT CONNECTOR

COOK TOP

GEAR

MOTOR

COVER

TYPICAL INSTALLATION

120 VAC

GROUNDED

OUTLET

PLANNINg

This downdraft blower system is

designed to be used to exhaust

airborne contaminants when

cooking with a variety of gas

or electric cooktops. It can be

mounted in island, peninsula, or

conventional wall locations.

This unit can be easily installed

following these basic steps:

• Cut out the countertop

opening.

• Mount the unit in the cabinet.

• Connect the ductwork and

electrical.

• Install the cooktop.

Note: The high level of air flow of this appliance may affect the

gas flame on some types of gas cooktops. This is NORMAL and

will cause no harm, but can be corrected by lowering the speed

of the blower.

LEVELING BRACKET -

FLANGE FACING IN

LEVELING BRACKET -

FLANGE FACING OUT

MOUNTING SCREWS

COVER PLATE

CLAMP

CHANNEL

NUT

BLOWER

MOTOR

PLUG

SHEET

METAL

SCREW

CLAMP

CHANNEL

NUTS

SHEET

METAL

SCREW

BOTTOM

FLANGE

BLOWER

PREPARATION

CHANgINg BLOWER DISCHARgE (Optional)

The blower is shipped with its discharge facing DOWN. Follow

these steps ONLY if:

the position of the blower discharge needs to be moved so duct-

work does not interfere with floor joists, plumbing or wiring below.

it is necessary to rotate the blower discharge to the RIGHT or LEFT.

Place the unit on its back on a table or work surface.

DOWN DISCHARgE - MOVINg BLOWER LEFT OR RIgHT

1. Loosen the 4 nuts and 2 clamp channels.

2. Slide blower to desired position.

3. Use supplied cover plate to close open space (if any).

4. Tighten wing nuts to secure top of blower and use sheet metal

screws through bottom flange to secure bottom of blower.

LEFT OR RIgHT DISCHARgE

1. Remove the 4 nuts and 2 clamp channels.

2. Carefully lift blower and disconnect motor plug if necessary.

Reposition blower and RECONNECT MOTOR PLUG.

3. Use supplied cover plate to close open space (if any).

4. Replace clamp channels and use nuts to secure the blower

in its new position.

5. Use sheet metal screws through bottom flange to secure bot-

tom of blower.

CUT COUNTERTOP OPENINg

1. Lay out and cut the cooktop cut-out far enough FORWARD

so downdraft will fit behind it.

2. Set cooktop in place and slide it as far forward as possible.

Center and square it with edges of countertop.

3. Place the plastic template against the back flange of the cook-

top and center it. Trace around template to mark the downdraft

opening.

4. Remove cooktop from countertop.

5. Cut downdraft opening. Be careful not to chip edges of coun-

tertop.

MOUNT THE UNIT

1. Set downdraft into opening. Extend leveling brackets to floor

of cabinet so downdraft sits straight. (Note: Leveling brackets

can be removed and re-attached in other positions. Bottom

flange may have to face inward in tight cabinet installations.)

2. Secure the downdraft to the countertop as follows: Hold the

downdraft against the back of countertop cut-out and tightening

the 2 mounting screws (one on each end of unit) on underside

of countertop. Use a wood shim between screw and underside

of granite countertops.

3. Screw leveling brackets to bottom of cabinet. Tighten screws

holding leveling bracket to unit on each side.

Product specificaties

Merk:	Broan
Categorie:	Afzuigkap
Model:	273003

Heb je hulp nodig?

Als je hulp nodig hebt met Broan 273003 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Afzuigkap Broan

Broan Elite E6430SSM Handleiding

2 November 2024

Broan Elite E6030SSM Handleiding

2 November 2024

Broan Elite RMIP45 Handleiding

3 April 2024

Broan Elite 619004 Handleiding

3 April 2024

Broan BWS1304SS Handleiding

3 April 2024

Broan EWS1306BLS Handleiding

3 April 2024

Broan BWP1304SS Handleiding

3 April 2024

Broan PM250 Handleiding

3 April 2024

Broan Elite 614804EX Handleiding

3 April 2024

Broan BWP1364SS Handleiding

3 April 2024

Handleiding Afzuigkap

Nieuwste handleidingen voor Afzuigkap

Bosch DWK91LT20 Handleiding

23 November 2024

Bosch DWB67JP50 Handleiding

23 November 2024

Bosch DWK65AD60R Handleiding

22 November 2024

Mayer MMSL901SM Handleiding

22 November 2024

Mayer MMBCH900I Handleiding

22 November 2024

Mayer MMSI903OT Handleiding

22 November 2024

Cecotec Bolero Flux TT 905500 Handleiding

22 November 2024

Cecotec Flux CM 603500 Handleiding

22 November 2024

Cecotec Bolero Flux TM 703500 Handleiding

22 November 2024

Cecotec Bolero Flux TLM 603500 Handleiding

22 November 2024