Britax KING II ATS Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Britax KING II ATS (4 pagina's) in de categorie Autostoel. Deze handleiding was nuttig voor 74 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/4
01
10
18
04
Adjustment lever
Headrest adjuster (KING II ATS/LS)
Lower belt guide
Release buttons
Seat shell
Upper belt guide Seat base
01
02
03
04
05
06
07
Indicator light (KING II LS)
Shoulder pads
Headrest
Headrest adjuster (KING II) Adjusting button
08
09
10
Shoulder straps
11
Harness buckle
12
13
14
Adjustment strap
Indicator light (KING II ATS)
15
16
Adjustment handle
17
User guide compartment
18
02
03
05
06
07
08
09
11
12
13
14
15
17 16
KING II / ATS / LS
User instructions
www.britax.com
2000021398 02/17
GB
9 kg - 18 kg
9 M ~ 4 Y
2. INTRODUCTION
We are delighted that our
KING II / ATS / LS
can safely accompany your child
through a new stage in its life.
In order to protect your child correctly, the
KING II / ATS / LS
must al-
ways be used and installed as described in these instructions.
If you have any further questions regarding its use, please feel free to contact us:
These instructions use the following symbols stated below:
Symbol Keyword Explanation
DANGER! Risk of severe personal injury
WARNING! Risk of minor personal injury
CAUTION! Risk of material damage
TIP: Useful notes
Instructions that follow a set sequence are numbered.
Example:
1. Press the button...
21
22
Belt guide colours
For better differentiation, the two vehicle seat
belts are highlighted in different colours. The di-
agonal seat belt 21 in dark red and the lap belt
22 in bright red. The colour of the belt guides
on the child safety seat follows the same colour
scheme.
4. CARE AND MAINTENANCE
3. CERTIFICATION
/ USAGE
PAGE I
5. DISASSEMBLY AND DISPOSAL
1. PRODUCT OVERVIEW
DISPOSAL:
Please observe the waste disposal regulations in your country..
Disposal of packaging Container for cardboard boxes
Seat cover Residual waste, thermal utilisation
Plastic parts According to the labelling in the
corresponding container
Metal parts Container for metals
Belt straps Container for polyester
Buckle and tongue Residual waste
Batteries Container for batteries
REMOVAL:
UNFASTENING YOUR CHILD:
1. To unfasten your child, press the red release button of the 5-Point harness
buckle 12 .
1. Unbuckle the vehicle belt buckle 20 and loosen the harness straps.
2. Unhook the diagonal belt section 21 from the upper belt guide 01 .
3. To open the shell: push one of the grey release buttons
03 and at the
same time pull the seat shell 02 as far forward as possible.
4. Remove the diagonal 21 and the lap belt sections 22 from the light red
lower belt guides 04 .
5. Hold the seat shell 02 with one hand while pulling the grey adjustment
lever 05 forward with the other hand.
6. To close the shell: tip the seat shell 02 against the seat base 06 over both
engagement positions.
WARNING! To avoid injuries take your hand away from the grey adjust-
ment lever 05 , as soon as getting over the two engagement positions.
7. Push the seat shell 02 with both hands against the seat base 06 until it is
fully engaged.
BRITAX RÖMER
Child safety seat
Testing and certication
In accordance with ECE* R 44/04
*ECE = European Standard for Child Safety Equipment
Group Body weight
KING II / ATS / LS
I 9 to 18 kg
The child safety seat has been designed, tested and certied according to the re-
quirements of the European Standard for Child Safety Equipment (ECE R 44/04).
The seal of approval E (in a circle) and the approval number are located on the
orange approval label (sticker on the child safety seat).
DANGER! This approval will be invalidated if you make any modications to
the child safety seat. Only the manufacturer is permitted to make
modications to the child safety seat.
Never secure your child or the child safety seat with a 2-point belt. DANGER!
If you secure your child in the child seat with only a 2-point belt,
then in the event of an accident this may cause serious injuries to
your child, possibly resulting in death.
Please observe the instructions for using children’s restraining systems in the operating
instructions of your vehicle. 3-point retractor safety-The seat can only be used in vehicles with
belts
2)
.
Please nd the information on the seats approved for child safety seats of the weight classes 9 to
18 kg in the operating instructions of your vehicle.
You can use your child safety seat as follows:
In the direction of travel yes
Against the direction of travel no
1)
with 2-point belt no
with 3-point reractor safety belt
2) yes
on front passenger seat yes
3)
on outer rear seat yes
on centre rear seat (with 3-point
belt2))
yes 4)
1) Use is permitted on a rearward-facing vehicle seat (e.g. in a van or minibus) only
if the vehicle seat is also approved for use by adults. The seat may not be in the area of effect
of an airbag.
2) The seat is only compatible with 3-point retractor type safety-belts, approved to ECE Reg
No. 16 or other equivalent standards.
3) If there is a front airbag: Slide the vehicle seat a long way back and refer to any instructions
in vehicle owner’s manual.
4) Cannot be used if the vehicle seat is equipped with only a 2-point belt.
9 - 18 kg
Removing the cover
Loosen the harness straps as far as possible.
1. Open the harness buckle 12 (press red button).
2. Remove the cover of the headrest 09 .
3. Open the poppers 29 on the left and right side of the
rear part of the cover.
4. Unhook the elastic seam of the cover under the edge of
the seat shell.
TIP: Start at the sides of the seat shell.
5. Pull the cover up and over the bezel of the strap adjuster.
6. Feed out the harness buckle 12 and the end of the strap
from the cover.
7. Pull the cover upwards and remove it over the headrest
09 .
The cover can now be washed. Please observe the
instructions on the washing label of the cover:
Re-tting the cover
Proceed in reverse order to put on the cover.
09
29
12
Please ensure that you only use the original BRITAX RÖMER replacement seat
covers, as the seat cover is an integral part of the child safety seat and fulls im-
portant functions to ensure the smooth operation of the system. Replacement seat
covers are available from your dealer.
• The cover can be removed and washed using the delicates programme of the
washing machine (30°C). Please observe the instructions on the washing label
of the cover.
• The plastic parts can be cleaned with a damp cloth. Do not use any caustic
cleaning agents (such as solvents).
DANGER! The child seat must not be used without the seat cover.
Care for the harness buckle
It is vital for the safety of your child that the harness buckle works correctly. Malfunctions
of the harness buckle are usually caused by accumulations of dirt or foreign bodies.
Malfunctions include the following:
• The buckle latches are ejected only slowly when the red release button is pressed.
• The buckle latches will no longer lock home (i.e. they are ejected again if you try to push
them in).
• The buckle latches engage without an audible “click“.
• The buckle latches are difcult to insert (you feel resistance).
• The buckle only opens if extreme force is applied.
Remedy: wash out the harness buckle so that it functions properly once again.
25
12
12
27
26
Cleaning the harness buckle
1. Open the harness buckle 12 (press the red button).
2. Adjust the seat shell 02 to the upright seating
position.
3. Open the Velcro fastener on the crotch pad
25 and
remove it and retain it.
4. Grasp below the seating area the metal plate
26
which keeps the buckle 12 at the seat base and
turn it into a vertical position.
5. Slide the metal plate 26 through the slot 27.
6. Soak the harness buckle 12 in warm water with
dishwashing liquid for at least an hour.
7. Rinse and dry the harness buckle 12 thoroughly.
8. Slide the metal plate 26 edgewise through the slot
27 in the cover and the seat base.
9. Rotate the metal plate 26 90°
DANGER! Pull the harness buckle 12 rmly to ensure
that it is securely fastened.
10. Insert the crotch pad 25 through the slot 27 and
secure the Velcro fastener.
Cleaning the occupant sensor
1. Fold the lower part of the cover updwards.
2. Remove dirt and dust in the area of the occupant sensor
28 with a vacuum cleaner.
DANGER! The occupant sensor 28 must not come in
contact with water.
28
9.2 BUCKLE UP YOUR CHILD
Product variant KING II:
Product variant KING II LS:
WARNING! Pull the adjuster strap 16 straight
forward (not upwards or downwards)
1. Pull the adjuster strap 16 until the indicator light 15
illuminates “green“ and you can hear an audible
sound.
►The belt tensioning of your child seat is now active
and removes excess belt length automatically within
a dened working range.
TIP! The green indicator light 15 turns off automatically
after a few seconds, but the system continues to work.
It is possible at any time to repeat step 1.
Your child seat is equiped with a system that automatically keeps the tension
within a dened working range in the harness once adjusted correctly and
also with indicator and alert functions. The system works with an occupant
sensor, so without your child sitting in the seat the indicator light will be off.
DANGER! The automatic harness tensioning system and indicator and
alert functions operate within limits and subject to correct usage. They provide
assistance only and do not replace safety checks, recommendations or requi-
rements or negate responsibility for them. You must always take full responsi-
bility for and periodically check the safety of your child.
Product variant KING II ATS:
DANGER! When the indicator light 15 illuminates
red your child is not properly secured or the auto-
matic retraction system has reached its limit. Stop
at the next safe opportunity and repeat the steps of
the chapter .“9.3 Securing your child“
TIP! If your child is still fastened, the alert can be
a warning that the automatic retraction system is at
the end of its working range. You may still have a t
well beyond your rst installation but the automatic
adjustment has stopped. You may either complete your
journey (with periodic checks on your child) or pullover
at the next convenient place and simply pull the adjus-
ter strap again (without unbuckling) to green to reload
your automatic retraction system, this will also reset
your alert system.
TIP! You can remove your sleeping child by pres-
sing and holding the mute button rst whilst undoing
the buckle.
DANGER! When the indicator light 15 ashes red
and green the batteries must be replaced.
Lift the seat cover and the foam cushion on the seating
surface and change the two type AAA batteries in the
battery compartment 24 .
8. INSTALLATION OF THE CHILD SEAT
1. Place the child seat facing in the direction of travel
on the vehicle seat.
2. Push one of the grey release buttons 03 and at the
same time pull the seat shell 02 as far forward as
possible.
DANGER! When opening or closing, nothing must
come between the seat shell 02 and the seat base
06 . You or your child could pinch your ngers,
injuring them.
3. Pull out the vehicle seat belt and place it between
seat shell 02 and seat base 06 through the two
lower light red belt guides 04 .
DANGER! Ensure that diagonal seat belt 21 and
lap belt 22 lie in both lower light red belt guides 04
and both belts are not twisted.
4. Engage the buckle tongue in the vehicle seat buckle
20 with an audible “CLICK“.
5. Tighten the diagonal belt section 21 by pulling the
diagonal belt 21 strongly on the opposite side from
the vehicle seat belt buckle.
6. Hold the seat shell 02 with one hand while pulling
the grey adjustment lever 05 forward with the
other hand. Tip the seat shell 02 against the seat
base 06 over both engagement positions.
WARNING! To avoid injuries take your hand away
from the grey adjustment lever 05 , as soon as
getting over the two engagement positions.
7. Push the seat shell 02 with both hands against the
seat base 06 until it is fully engaged.
DANGER! The two red safety markings on the
grey release buttons must not be visible.
8. Place the diagonal belt section 21 in the upper dark
red belt guide 01 .
9. Give the child seat a rm pull forwards to ensure
that it is securely fastened.
10. Observe the steps in the chapter
10.1 “ADJUSTING THE HEADREST“ .
11. Observe the steps in the chapter
10.2 “BUCKLE UP YOUR CHILD“.
9. 1 ADJUSTING THE HEADREST
1. Loosening the harness
Press the adjustment button 13 and at the same time
pull below the shoulder pads 10 both shoulder straps
11 forward.
The headrest 09 must be adjusted so that the top of
the harness shoulder pads are in-line with your child‘s
shoulders.
If your child is wearing thick clothing you may need to
raise the headrest again to ensure correct positioning
of the harness.
2. Adjusting the headrest for:
KING II ATS / LS
1. Sit your child in the seat and check the height of the
headrest 09 .
2. Pull / push the headrest adjuster 07 to move the
headrest up or down.
3. Repeat the procedure until the headrest
09 is at the
correct height.
WARNING! If the headrest is positioned too low
it can seriously compromise the effectiveness of the
harness, and indicator systems.
KING II
1. Pull the lever of the headrest adjuster
08 at the
rear of the seat shell 02
Now the headrest is unlocked.
2. Slide the unlocked headrest adjuster
09 into the
desired diection to the correct height. As soon as
you release the lever of the headrest adjuster
08 ,
the headrest 09 engages.
3. Sit your child in the seat and check the height of
the headrest 09. Repeat the procedure until the
headrest 09 is at the correct height.
It is important to set the headrest 09 height position correctly for optimal
5-point harness operation and ensure the safety of your child.
To adjust the height of the headrest to t your child:
The seat shell of the KING II / ATS / LS can be put into four different angles:
8. Pull shoulder straps 11
to remove all slack from
the lap section ensuring
the harness lies at and
has a snug t.
1. Open the harness buckle 12 (press red button)
2. Press the adjusting button 13 and at the same time
pull below the shoulder pads 11 both shoulder
straps 10 forward.
3. Sit your child down in the seat.
4. Check the correct height of the headrest and adjust it
if necessary [see above].
5. Make sure that your child´s back lies at against the
backrest of the child seat.
6. Unhook the buckle tongues 23 from the harness
retainers 19 .
7. Guide the two buckle latches 23 together and engage
them before putting them into the harness buckle12
- this should make an audible click.
DANGER! The lap belts 24 must be positioned as low as possible over
your child‘s hips.
9. Carry out the steps in section for your “9.3 SECURING YOUR CHILD“
particular product variant.
1. Pull on the adjusting strap 16 until the harness lies
at and is close against your child‘s body.
WARNING! Pull the adjuster strap 16 straight
forward (not upwards or downwards).
1. Pull the adjuster strap 16 until the indicator light 14
illuminates “green“ and you can hear an audible
“Click“ which indicates that the harness is tightened
correctly.
TIP! The green indicator light turns off automatically after
a few seconds.
2. Observe the safety notes in the chapter
“8. INSTALLATION OF THE CHILD SEAT“
9.3 SECURING YOUR CHILD
WARNING! Pull out the adjusting strap 16 straight
forward.
The more snugly the harness ts over your child‘s body, the better your child will be
protected. Therefore avoid putting thick clothes on your child under the belt.
2. Observe the safety notes in the chapter
“8. INSTALLATION OF THE CHILD SEAT“
What to do when the indicator light does not illuminate “green“ ...
● Check if the headrest is adjusted correctly according to the chapter
“9.1 ADJUSTING THE HEADREST“.
● Ensure that you have pulled the adjuster strap with enough force.
● In general the battery in the product is a non replaceable item and must not be
changed due to its long life.
● If the problem can not be resolved using the above methods, contact your
service representative or the BRITAX RÖMER Customer Service.
What to do when the indicator light does not illuminate at all...
● Check if the headrest is adjusted correctly according to the chapter “9.1
ADJUSTING THE HEADREST“.
● Check if there is any accumulation of dirt or foreign objects on the seating
area under the occupant sensor.
If necessary clean the area as described in chapter 4 [page I].
● Replace both batteries
● Ensure that you have pulled the adjuster strap with enough force.
If the problem can not be resolved using the above methods, contact your service
representative or the BRITAX RÖMER customer service.
Please take the time to read these instructions carefully and keep
them to hand in the intended storage compartment 18 on the child
safety seat at all times! The instructions must be with the child safety
seat if the latter is passed on to a third party.
DANGER! For the protection of your child:
• Use the KING II / ATS / LS exclusively for securing your child in your
vehicle. It is in no way suitable as a seat or toy in the home.
• In the event of an accident with a collision speed of more than 10 km/h, the
child safety seat may be damaged without the damage becoming immediate-
ly visible. In this case the child safety seat must be replaced. Please dispose
of it properly.
• Have your child safety seat checked as a rule if it was damaged (e.g if it
falls to the ground).
• Regularly check all important parts for damage. Ensure that all mechanical
parts, in particular, are fully functional.
• Never lubricate or oil parts of the child seat.
•
Never leave your child unattended in the child seat in the vehicle.
• Let your child in and out of the vehicle from the pavement side as a rule.
• Protect the child safety seat against intensive direct sun radiation,
as long as it is not in use.The child safety seat can become very hot under
direct sun radiation. Child skin is sensitive and could thereby be injured.
•
The more snugly the harness ts over your child's body, the better your child will
be protected. Therefore avoid putting thick clothes on your child under the belt.
• Take regular breaks on long journeys in order to give your child the opportu-
nity to play around when removed from the child seat.
• Use on the rear seat: Push the front seat forwards sufciently so that the
feet of your child cannot hit the backrest of the front seat (to avoid the risk
of injury).
DANGER! For the protection of all vehicle occupants:
In the case of an emergency stop or an accident, unsecured persons or
objects may cause injury to other vehicle occupants. Please always check
that...
• the backrests of the vehicle seats are locked (i.e. that a foldable rear seat
bench latch is engaged).
• all heavy or sharp-edged objects in the vehicle (e.g. on the parcel shelf) are
secured.
• all persons in the vehicle have their seatbelts fastened.
• the child safety seat is always secured when it is in the vehicle, even if no
child is being transported.
WARNING! For your protection when handling the child seat:
• Never use the child safety seat free-standing, not even for test sitting.
• When opening or closing, nothing must come between the seat shell
02
and the seat base 06. You or your child could pinch your ngers, injuring
them.
•
To avoid damage, ensure that the child safety seat is not jammed in between
hard objects (car door, seat rails, etc.).
•
Keep the child safety seat in a safe place if it is not in use. Do not place any
heavy objects on the seat and do not store it directly next to sources of heat or
in direct sunlight.
CAUTION! To protect your vehicle:
•
Certain car seat covers made from more sensitive materials (e.g. velour, leath-
er, etc.) may sustain signs of wear and tear when using child safety seats. For the
optimum protection of your car seat covers, we recommend using the BRITAX
RÖMER Car Seat Protector from our accessories programme.
6. SAFETY NOTES
PAGE II
7. ANGLE ADJUSTMENT
To adjust the angle:
Lift the adjustment handle 17 and pull/push the seat
shell 02 into the desired position.
DANGER! The seat shell 02 must engage secu-
rely regardless of its position. Pull on the seat shell
02 to ensure that it is engaged properly.
TIP! You can also adjust the angle of the seat shell
02 when your child is sitting in the child seat.
For the safety of your child, before every journey in the car check
that ...
► the child safety seat is securely fastened,
► seat shell 02 and seat base 06 are fully engaged. The both red safety
marks on the grey release buttons 03 must not be visible.
►the diagonal 21 and the lap seat belt sections 22 run on both sides
through the light red lower belt guides 04 ,
►the diagonal seat belt section 21 runs through the upper dark red belt
guide 01 ,
►diagonal 21 and lap seat belt sections 22 are tight and twisted,not
►the vehicle seatbelt buckle 20 is positioned between the lower light not
red belt guides 04 of the child seat.
►the headrest is adjusted correctly,
►the 5-point harness of your child seat are comfortable but FIRM t around
your child,
►the straps of the 5-point harness are twisted,not
►the buckle tongues 23 are engaged in the harness buckle 12 .
DANGER! If your child tries to open the vehicle belt buckle
20
, or the 5-point
harness buckle
12
stop immediately as soon as safely possible. Check
whether the child safety seat is correctly fastened and ensure that your child
is correctly secured. Explain to your child the dangers associated with their
actions.
UNFASTENING YOUR CHILD AND REMOVAL:
To unfasten your child or to remove the child safety seat, observe the
steps in Section 5 “DISASEMBLY AND DISPOSAL“ [PAGE I]
02
17
02
03 06
02
06
04
04
20
05
02
06
21
01
06
02
03
16
12
23
12
13
11
10
09
13
11
10
07
09
08
02
beep!
16
15
24
15
15
15
16
15
21
22
24
11
DANGER! Batteries for the ATS product variant:
● The batteries must be replaced by an adult. ● Keep batteries out of the
reach of children.● Use only new batteries of the same type.● Use only 2x
AAA type, 1.5 volts batteries.● Never use batteries that show signs of leaka-
ge.● Remove the old batteries and dispose of them according to the disposal
instructions on page I, chapter 5.● Do not expose the batteries to excessive
heat or re, the batteries may burst or explode.● Due to lower voltage do not
use rechargeable batteries.● Observe the warning on the packaging of your
batteries.
beep!
15
Product specificaties
Merk: | Britax |
Categorie: | Autostoel |
Model: | KING II ATS |
Kleur van het product: | Black, Grey |
Gewicht: | 10300 g |
Breedte: | 450 mm |
Diepte: | 540 mm |
Hoogte: | 670 mm |
Maximale gewichtscapaciteit: | 18 kg |
Aantal: | 1 |
Minimale gewichtscapaciteit: | 9 kg |
Riem vastmaak systeem: | 3 punten |
Autostoel groep: | 1 (9 - 18 kg; 9 maanden - 4 jaar) |
Plaatsing beschikbaar: | Naar voren gericht |
Heb je hulp nodig?
Als je hulp nodig hebt met Britax KING II ATS stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Autostoel Britax
8 Juli 2023
4 Juli 2023
22 Juni 2023
19 Juni 2023
16 Juni 2023
15 Juni 2023
15 Juni 2023
14 Juni 2023
12 Juni 2023
12 Juni 2023
Handleiding Autostoel
- Autostoel Axkid
- Autostoel Baby Jogger
- Autostoel BabyGO
- Autostoel Be Cool
- Autostoel Bebe Confort
- Autostoel BeSafe
- Autostoel Brevi
- Autostoel Britax-Romer
- Autostoel Bugaboo
- Autostoel Dometic
- Autostoel Ellermeyer
- Autostoel Fisher Price
- Autostoel Foppapedretti
- Autostoel Giordani
- Autostoel Graco
- Autostoel Hauck
- Autostoel Inglesina
- Autostoel Kiddy
- Autostoel Kinderkraft
- Autostoel Lorelli
- Autostoel Maxi-Cosi
- Autostoel Migo
- Autostoel Nuna
- Autostoel Peg Perego
- Autostoel Recaro
- Autostoel Romer
- Autostoel Safety 1st
- Autostoel Sena
- Autostoel Stokke
- Autostoel Storchenmuhle
- Autostoel Ultimate Speed
- Autostoel Uppababy
- Autostoel X-Adventure
- Autostoel Jane
- Autostoel Joie
- Autostoel Osann
- Autostoel Baninni
- Autostoel Lionelo
- Autostoel Hamron
- Autostoel Chicco
- Autostoel Plebani
- Autostoel Cosatto
- Autostoel Silver Cross
- Autostoel Biltema
- Autostoel Casualplay
- Autostoel Concord
- Autostoel Cybex
- Autostoel Evenflo
- Autostoel Kikka Boo
- Autostoel Mothers Choice
- Autostoel Mountain Buggy
- Autostoel Phil And Teds
- Autostoel Baby Trend
- Autostoel Disney
- Autostoel Apramo
- Autostoel Cangaroo
- Autostoel Caretero
- Autostoel Clek
- Autostoel Infasecure
- Autostoel Klippan
- Autostoel Nania
- Autostoel Petex
- Autostoel Renolux
- Autostoel Burigotto
- Autostoel Xadventure
- Autostoel Chipolino
- Autostoel Heyner
- Autostoel Takata
- Autostoel Beemoo
- Autostoel Hipod
- Autostoel Kindercraft
- Autostoel Walser
Nieuwste handleidingen voor Autostoel
23 December 2024
23 December 2024
23 December 2024
23 December 2024
23 December 2024
23 December 2024
23 December 2024
23 December 2024
23 December 2024
20 December 2024