Brinsea Octagon 20 ECO Handleiding

Brinsea Niet gecategoriseerd Octagon 20 ECO

Lees hieronder de 📖 handleiding in het Nederlandse voor Brinsea Octagon 20 ECO (78 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 54 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/78
AE21 GB Issue 02
1
Octagon 20 Eco and Octagon 40 Eco
egg incubators
User instructions
Contents
Section Subject Page
1 Introduction 2
2 Unpacking 2
3 Location, Installation and Temperature 3
4 Storage of eggs 5
5 Humidity and Ventilation 5
6 Egg setting 8
7 Egg turning 8
8 Hatching 8
9 Cleaning up 9
10 Servicing 9
11 10 Troubleshooting
12 11 Specifications
AE21 GB Issue 02
2
1 Introduction
Read the instructions before use.
These instructions detail the operation of your new Octagon 20 Eco or Octagon 40 Eco incubator and optional
Autoturn Cradle. Please read these instructions carefully before setting up your machine to achieve best results
and keep these instructions safe for future reference. This document includes recommended procedures for
successful hatching but incubation involves the control and manipulation of a large number of factors and in
certain circumstances different procedures may be necessary. Your incubator is designed to allow the user to
vary the incubation conditions to suit a wide range of species in different ambient conditions and the specific set-
up for every situation is beyond the scope of these instructions.
There is a range of books available covering incubation techniques, for more information or to request a book list
please don’t hesitate to contact us.
DO NOT COVER THE INCUBATOR. FOR INDOOR USE ONLY. THE INCUBATOR MUST BE PLACED
IN AN AREA NOT SUBJECT TO SPLASHES OF WATER OR WET CONDITIONS AND OUT OF REACH
OF ANIMALS AND CHILDREN.
Fig. 1 Functional features of the Octagon 20 Eco (Octagon 40 Eco functionally similar)
2 Unpacking
Your incubator has been supplied in protective packaging. Please remove all tape, strapping and packing from
the incubator and parts. Retain the carton and packing materials to enable the unit to be repacked.
Your incubator will include as standard:
Quantity (Octagon 20 Eco) Quantity (Octagon 40 Eco) Item
1 1 Incubator (including removable lid)
1 2 Egg tray
1 1 Cable cover and screw
1 1 Mains cable
6 Wire egg dividers 12
Autoturn Cradle
Temperature Control
Housing
Heater Indicator LED
Adjustable Air Vent
Turning Motor
Housing
Cable / Adjustment
Spindle Cover
(remove to access
tamper-proof
temperature adjuster)
Liquid- -glass in
Thermometer
AE21 GB Issue 02
3
Optional Autoturn Cradle:-
2 Base bars
1 Motorised cradle end
1 Plain cradle end
1 Set of four bolts
2.1 Please identify each part and check that they are all present and undamaged. If there are any parts
damaged or missing please contact your retailer or Brinsea Products (at the address at the end of the
document). Damaged appliances shall not be used.
2.2 Check also that the electrical supply matches the machine’s requirements (marked on the technical label
on the inside of the lid of the incubator and on the inside of the blank Autoturn cradle end). The power
cord set must be an appropriately rated and approved cord-set in accordance with the regulations of the
country it is used in.
2.3 To register your new Brinsea product please visit www.brinsea.co.uk and follow the link on the right
hand side of the home page to qualify for your free 2 year guarantee.
2.4 Go to www.Brinsea.co.uk and register as a free member of the Brinsea Email Group to receive the latest
news and information such as advance notice about new products, special offers, exclusive competitions
and much more.
3 Location, Installation and Temperature
3.1 Your incubator will give best results in a room free from wide temperature variations and with generous
ventilation particularly if several incubators are running at the same time. Ensure that the room
temperature cannot drop on a cold night. Ideally thermostatically control the room at between 20 and
25°C (68 and 77°F). Never allow the room temperature to drop below 15°C (59°F) and ensure that the
incubator cannot be exposed to direct sunlight. Do not use your incubator on the floor.
3.2 If using the Autoturn cradle: Assemble the Autoturn cradle in accordance with the diagram below (Fig. 2)
and place on a flat, level surface (workbench height is ideal). Place the incubator into the Autoturn cradle
as illustrated (Fig. 1). The cabinet is designed to locate onto the lugs at either end of the Autoturn cradle.
Take care to offer the incubator at the angle which matches that of the drive lug to avoid damage to the
mechanism. Ensure full engagement in the slots in the ends of the incubator so that the incubator is level
end to end.
FIG. 2
3.3 If using without the Autoturn cradle place the incubator upright on a flat level surface.
3.4 Remove the lid and place it where it can not be splashed by water. Lift out the egg tray and fill one of the
two water channels (Octagon 20) or two of the four water channels (Octagon 40) with water or 100:1
Brinsea Incubation Disinfectant Solution leaving the top of the liquid 3/4 (20mm) from the top of the
channel. Replace the tray and replace the lid. Slide the ventilation control to the centre of its range.


Product specificaties

Merk: Brinsea
Categorie: Niet gecategoriseerd
Model: Octagon 20 ECO

Heb je hulp nodig?

Als je hulp nodig hebt met Brinsea Octagon 20 ECO stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Brinsea

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd