Braun ProGlide-Jet PV 2212 Handleiding

Braun Strijkijzer ProGlide-Jet PV 2212

Lees hieronder de 📖 handleiding in het Nederlandse voor Braun ProGlide-Jet PV 2212 (5 pagina's) in de categorie Strijkijzer. Deze handleiding was nuttig voor 67 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/5
ProGlide-jet
PV 2202
PV 2205
PV 2210
PV 2212 Type 4692
Steam iron
English
Use Instructions
Guarantee
Service Centers
English
Ceramic sole plate
Your Braun steam iron has a unique,
new sole plate made out of a special gliding
ceramic material. This process engineered
by Braun makes the sole plate extremely
easy gliding. Thanks to its properties you
will save time during the ironing process.
2 3
Our products are engineered to meet the
highest standards of quality, functionality
and design. We hope you thoroughly enjoy
your new Braun steam iron.
Important Safeguards
Read all instructions carefully before using the iron. Keep the use instructions during the
entire life of the iron.
Before filling with water, always disconnect the plug from the socket first.
Always pull the plug and not the cord.
Electric irons reach high temperatures during operation that could lead to burns.
Keep the iron away from children, and when it is turned on, keep the unit under supervision.
Disconnect the plug when leaving the room where you are ironing, even if it is only briefly.
Never iron or dampen clothes while wearing them.
During ironing pauses, always place the iron upright in its heel rest.
Never immerse the iron in water or other liquids.
The cord should never come into contact with hot objects or the sole plate.
Check the cord periodically for possible damage.
Do not use a damaged iron.
Take it to a Braun Service Center for repair.
Braun electric appliances meet applicable safety standards.
This appliance can only be opened by an authorised Braun Service Centre for repairs.
The cord of this appliance may only be replaced by an authorised Braun Service Centre since
special tools are required.
Faulty, unqualified repair work may cause accidents or injury to the user.
Make sure your voltage corresponds to that printed on the iron. Connect the iron to an alternating
current (~) outlet only.
Table of features for each model
Feature: Model: PV 2202 PV 2205 PV 2210 PV 2212
Jet of steam
Shot of steam
Extra steam
Spray
Specifications
Voltage/wattage: See typeplate at the
bottom of the unit.
Water tank capacity: 215 cc (approximately
1 filling beaker
q
of water filled up to the
mark = 1 tank filling).
Description
1
Temperature selector
2
Water tank with sliding shutter opening
3
Water spray nozzle
4
Steam regulator / self-cleaning activator
and anti-calc. valve
5
Extra steam button
6
Jet of steam button
7
1- or 2-function button (water-spray/
shot of steam, see «Table of features»)
8
Pilot light
9
Pivoting cord
j
Heel rest
k
Cord storage/typeplate
l
Transparent water tank
L
Maximum marking («max.»)
m
Sole plate with 71 steam vents
n
Full-lenght button groove
o
Slim pointed tip
p
Jet of steam outlet
q
Filling beaker
proglide-jet
jet
jet
-jet
max
jet
max
min
sc
jet
max
min
sc
shot
spray
shot
spray
jet
shot
s
e
l
f
c
l
e
a
n
i
n
g
s
e
l
f
c
l
e
a
n
i
n
g
2
3
4
5
7
8
11
9
10
17
12
1
16
15 14
b
e
g h
f
c d
a
6
13
12a
4
Praktical Guidelines
Type of Water to be Used
This iron is designed for tap water. However, if
you have hard water we recommend to use a
mixture of 1/2 part tap water and 1/2 part distilled
water from drug stores or grocery stores.
Important: Never use distilled water (battery
water). Do not add any additives (e. g. starch) to
the water.
To fill iron
1. Pull the plug out of the wall outlet.
2. Put the steam regulator
4
in position «
»
(= steam off).
3. Open sliding shutter
2
.
4. Place the iron in the upright position and fill
with water slowly through the tank opening
2
to the «max.» marking
L
(a), using the
beaker
q
.
5. Close sliding shutter.
Selecting the temperature
Connect the iron to a safely located wall outlet
and select the ironing temperature with the
temperature selector
1
(b). As soon as the pilot
light
8
goes out, the iron has reached the
temperature selected. To avoid water dripping,
always rest the iron upright while heating it up
keep the steam regulator
4
in position «
»
(= steam off) (c).
You will usually find the following symbols in your
garments:
The temperature selector
1
is marked with
these symbols:
min. The iron is connected
Synthetics (acrylic, acetate)
●●
Silk/rayon/nylon/polyester/
cotton blends/wool
●●●
Cotton/linen
max. Linen
Select the temperature you need according to
these symbols.
Spray, shot of steam, jet of steam
Before you start ironing, we recommend to press
the buttons 3 or 4 times, in order to activate
these functions.
Dry ironing
Set the steam regulator
4
in position «
»
(= steam off) (c) for dry ironing. The water
spray
7
may be used at any temperature
setting to dampen the laundry. The jet of steam
6
and the shot of steam
7
buttons can be
activated during dry ironing, provided that the
temperature selector
1
is within the continuous
red area
Steam ironing
(see «Table of features»)
Temperature selection: Set the temperature
selector
1
within the red
range steam (b) and wait
until the iron has reached the selected
temperature (i. e. the pilot light
8
goes off).
Steam ironing is possible in the entire red range.
Steam ironing at lower temperatures may cause
water drops instead of steam. Should this
happen, turn the steam regulator
4
to the
position «
» (= steam off) (c).
Steam regulator
4
:
Select the quantity of
steam required (c) for
each garment with the
steam regulator
4
. You
can increase the quantity
by turning the steam
regulator clockwise (wide
markings) to the end of the red marking.
Caution: While ironing do not turn the steam
regulator further, otherwise hot water may come
out from the sole plate (see section
«Decalcifying/Self-cleaning»).
By turning the steam regulator anti-clockwise
you can reduce the quantity of steam or turn the
steam off «
» (= steam off) (see «Ironing
Guide»).
Constant steam: Your braun steam iron ist
equipped with a special tank configuration to
provide constant steam even when the water
level in the tank is low.
Extra steam*
(coming from the
steam vents in the sole
plate): For stubborn
creases and wrinkles,
collars and cuffs.
When ironing within
the red range
area the extra steam function can
be used. You can press the button
5
(d) for 3
seconds at intervals of no less than 15 seconds.
5
Jet of steam*
(coming from the outlets
p
at the slim pointed tip)
o
): Caution:
Keep children away from
the jet of steam and do
not hold your fingers in
front of the outlets
p
when activating this function.
When ironing within the red range
area the jet of steam function
6
can be used (e). To do so, press the button
6
at
intervals of no less than 5 seconds. The jet of
steam has been designed not only for steaming
hard to reach areas like pleats, inside of pockets
etc., but also for steaming hanging clothing (e. g.
velvet skirts, curtains, etc.) (g). The jet of steam
functions between horizontal and upright
positions. Be careful not to touch sensitive
textiles with the hot sole plate.
Shot of steam*
(coming from the vents
in the sole plate):
When ironing within the
red area
the shot
of steam function can be
used. It gives an extra,
particularly powerful shot of steam penetrating
deep into the textiles in order to straighten
creases, collars and pleats. The function «shot
of steam» can be used in normal ironing and
also horizontally for steaming hanging clothing
(e. g. velvet skirts, curtains etc.) (g). Press the
shot of steam button
7
at intervals of no less
than 5 seconds. When steaming be careful not to
touch sensitive textiles with the hot sole plate.
* If pressed too frequently, it can drip. Should this
happen, wait a few seconds before using it
again.
Spray (coming from the
nozzle
3
): The spray
function can be used at
any temperature, to
dampen laundry. To do
so, press the button
7
(water spray = blue).
Spray / shot of steam
2-function button:
With the models 2210 and
2212 the functions «water
spray» and «shot of
steam» can be activated
with a 2-function button.
The desired function can
be selected by turning the
button
7
as far as it will
go. The marking (blue =
water spray or red = shot
of steam) must point to
the respective function (f).
Turn the button from blue
(spray) to red (shot of
steam) anti-clockwise
and from red to blue clockwise (f).
Storage
After ironing, always pull the plug out of the wall
outlet. Set the temperature selector
1
to «min.»
(b) and the steam regulator
4
to «
» (= steam
off) (c).
To empty the iron hold it with the open water tank
opening
2
downwards (h) and shake it 1 or 2
times. The pivoting cord
9
conveniently winds
up around the cord storage
k
.
IMPORTANT: Store the cool steam iron in a dry
place and always standing on its heel rest
j
.
The sole plate may be damaged by remaining
water if it is stored horizontally. The warranty
does not cover faults or damage resulting from
improper storage of the iron.
Maintenance and Cleaning
To remove residues of minerals/starch from the
sole plate always use steel wool. Never use a
scouring pad, vinegar or other chemicals. The
steam vents
m
and jet of steam outlets
p
may
be cleaned manually with a toothpick, if
necessary. Clean the sole plate regularly if you
use starch or other aids on the clothes for
ironing.


Product specificaties

Merk: Braun
Categorie: Strijkijzer
Model: ProGlide-Jet PV 2212

Heb je hulp nodig?

Als je hulp nodig hebt met Braun ProGlide-Jet PV 2212 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Strijkijzer Braun

Handleiding Strijkijzer

Nieuwste handleidingen voor Strijkijzer