Boss Metal Zone MT-2 Handleiding

Boss Niet gecategoriseerd Metal Zone MT-2

Lees hieronder de 📖 handleiding in het Nederlandse voor Boss Metal Zone MT-2 (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
Owner’s Manual
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).
After reading, keep the document(s) where it will be available for immediate reference.
AC Adaptor
(PSA series; sold separately)
Electric Guitar
English
LEVEL knob
This knob adjusts the volume of the eect sound. Set this knob so that there will
be no dierence in volume between the eect and straight sounds.
* No sound will be heard when this knob is rotated completely
counterclockwise.
7The MT-2 is compact yet creates powerful eect pedal which, through the use of high-level gain circuits, creates heavy distortion and sustain eects.
7The MT-2 includes a three-band equalizer, Low, Middle and High. The middle band EQ is adopted for parametric type.
OUTPUT jack
Connect an amplier or other eect unit to this
jack.
Guitar Amplier
DC IN jack
Accepts connection of an AC Adaptor (PSA series; sold separately). By using an AC Adaptor, you can play
without being concerned about how much battery power you have left.
* We recommend that you keep batteries installed in the unit even though you’ll be powering it
with the AC adaptor. That way, you’ll be able to continue a performance even if the cord of the
AC adaptor gets accidentally disconnected from the unit.
* Use only the specied AC adaptor (PSA-series).
* If the AC adaptor is connected while power is on, the power supply is
drawn from the AC adaptor.
CHECK indicator
This indicator shows whether an eect is ON/OFF, and doubles as the Battery Check indicator.
The indicator lights when an eect is ON.
* If this indicator goes dim or no longer lights while an eect is ON, the battery is near
exhaustion and should be replaced immediately.
* The CHECK indicator shows whether the eect is on or o, and indicates the dierent
functions. It does not indicate whether the power to the device is on or not.
EQUALIZER HIGH knob
This knob controls the tone of the eect sound at higher frequencies.
Rotating the knob clockwise boosts the higher frequencies, while rotating it
counterclockwise cuts the higher frequencies. Higher frequencies have a variable
range of ±15 dB.
Pedal Switch
This switch turns the eects ON/OFF.
Thumbscrew
When this screw is loosened, the pedal will open, allowing you to change the
battery.
* For instructions on changing the battery, refer to “Changing the
Battery.”
Panel Descriptions
Main Features
Precautions When Connecting
* To prevent malfunction and equipment failure, always turn
down the volume, and turn o all the units before making any
connections.
* Once the connections have been completed, turn on power
to your various devices in the order specied. By turning on
devices in the wrong order, you risk causing malfunction and/
or damage to speakers and other devices.
When powering up: Turn on the power to your guitar amp last.
When powering down: Turn o the power to your guitar amp rst.
* Before turning the unit on/o, always be sure to turn the
volume down. Even with the volume turned down, you might
hear some sound when switching the unit on/o. However,
this is normal and does not indicate a malfunction.
Operating the Unit
1. When you have made the
necessary connections, set
the knobs as shown in the
illustration.
2. Press the Pedal Switch.
Make sure the CHECK indicator lights.
3. Adjust the level of distortion
using the DIST knob.
Rotating the knob clockwise
increases the distortion level
while rotating it counterclockwise
decreases it.
* If this knob is set too high, the noise
will increase and oscillation may occur.
4. Adjust the tone of the middle
range with the EQUALIZER
MIDDLE knob.
Rotating the knob clockwise boosts
the frequency while rotating it
counterclockwise cuts it.
5. Set the middle frequency (to be boosted or cut) with the
EQUALIZER MID FREQ knob.
* When the EQUALIZER MIDDLE knob is set to the center position, moving
the EQUALIZER MID FREQ konb does not aect the sound.
6. Adjust the tone of the high range
with the EQUALIZER HIGH knob.
Rotating the knob clockwise boosts
the higher frequencies while rotating
it counterclockwise cut them.
7. Adjust the tone of the low range
with the EQUALIZER LOW knob.
Rotating the knob clockwise boosts the lower frequencies while
rotating it counterclockwise cut them.
8. Using the LEVEL knob, adjust the
volume of the eect sound so
that there will be no dierence in
volume between the eect and
straight sounds.
Use of Battery
* A battery was installed in the unit before it left the factory. The
life of this battery may be limited, however, since its primary
purpose was to enable testing.
* If you handle batteries improperly, you risk explosion and uid
leakage. Make sure that you carefully observe all of the items
related to batteries that are listed in “USING THE UNIT SAFELY”
and “IMPORTANT NOTES” (supplied on a separate sheet).
* When operating on battery power only, the unit’s indicator will
become dim when battery power gets too low. Replace the
battery as soon as possible.
* Batteries should always be installed or replaced before
connecting any other devices. This way, you can prevent
malfunction and damage.
Changing the Battery
1. Hold down the
pedal and loosen
the thumbscrew,
then open the
pedal upward.
* The pedal can be
opened without
detaching the
thumbscrew
completely.
2. Remove the old
battery from the
battery housing,
and remove the snap cord connected to it.
3. Connect the snap cord to the new battery, and place
the battery inside the battery housing.
* Be sure to carefully observe the battery’s polarity (+ versus -).
4. Slip the coil spring onto the spring base on the back of
the pedal, and then close the pedal.
* Carefully avoid getting the snap cord caught in the pedal, coil spring, and
battery housing.
5. Finally, insert the thumbscrew into the guide bush
hole and fasten it securely.
Main Specications
BOSS MT-2: Metal Zone
Nominal Input Level -20 dBu
Input Impedance 1 MΩ
Nominal Output Level -20 dBu
Output Impedance 1 kΩ
Recommended Load
Impedance 10 kΩ or greater
Power Supply DC 9 V: Dry battery 6F22 (9 V) type (carbon),
AC Adaptor (PSA-series: optional)
Current Draw 30 mA
* Expected battery life under continuous use:
Carbon: Approx. 12.5 hours
Alkaline: Approx. 23.5 hours
These gures will vary depending on the
actual conditions of use.
Dimensions 73 (W) x 129 (D) x 59 (H) mm
2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches
Weight 385 g/14 oz (including battery)
Accessories Owner’s Manual, Leaet (“USING THE UNIT
SAFELY,” “IMPORTANT NOTES,” and “Informa-
tion”), Dry battery/9 V type (6F22)
Options AC adaptor (PSA-series)
* 0 dBu = 0.775 Vrms
* This document explains the specications of the product at the
time that the document was issued. For the latest information,
refer to the Roland website.
Thumbscrew
Battery Housing
Pedal
Spring Base
Coil Spring
Guide Bush
Hole
Battery Snap
Cord
Battery
Snap
9 V Battery
EQUALIZER MIDDLE knob
This knob boosts or cuts the frequency you set with the EQUALIZER MID FREQ
knob. Rotating the knob clockwise boosts the level of the middle frequencies,
while rotating it counterclockwise cuts the level of the middle frequencies.
EQUALIZER MID FREQ knob
This knob sets the frequency of the middle range (200 Hz to 5 kHz). Rotating the
knob clockwise raises the frequency. Rotating it counterclockwise lowers the
frequency.
* When the EQUALIZER MID FREQ knob is set to the center position,
the EQUALIZER MID FREQ knob does not aect the sound.
DIST knob
This knob controls the intensity of the distortion eect. Rotating the knob
clockwise increases the distortion level.
* If you set this knob too high, the noise will increase and oscillation
may occur.
Sample Settings
Heavy Metal
Hard Rock
Overdrive
Fuzz
British Rock
Rock 1
Rock’n’roll
Rock 2
EQUALIZER LOW knob
This knob controls the tone of the eect sound at lower frequencies. Rotating the
knob clockwise boosts the lower frequencies, while rotating it counterclockwise
cuts the lower frequencies. The lower frequencies have a variable range of ±15
dB.
INPUT jack
This jack accepts input signals (coming from a guitar, some other musical
instrument, or another eects unit).
* The INPUT jack also serves as the power
switch. Power is turned on whenever a plug
is inserted into the INPUT jack, and is turned
o when the plug is disconnected. When
not using the unit, you should disconnect
any cord connected to the INPUT jack.
* 5 1 0 0 0 6 9 0 3 1 - 0 1 *
© 2016 Roland Corporation


Product specificaties

Merk: Boss
Categorie: Niet gecategoriseerd
Model: Metal Zone MT-2

Heb je hulp nodig?

Als je hulp nodig hebt met Boss Metal Zone MT-2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Boss

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd