Boss DD-3T Handleiding

Boss Niet gecategoriseerd DD-3T

Lees hieronder de 📖 handleiding in het Nederlandse voor Boss DD-3T (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 43 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

INPUT jack (Power switch)

Inputs the sound to which delay is applied. Connect your electric guitar,

other instrument, or eect unit here.

About power on/o

The INPUT jack also serves as the power

switch. Power is turned on whenever a plug is

inserted into the INPUT jack, and is turned o

when the plug is disconnected.

* To prevent unnecessary battery consumption, be sure

to disconnect the plug from the INPUT jack when not

using the unit.

Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).

After reading, keep the document(s) where it will be available for immediate reference.

English

OUTPUT jack

Outputs a mix of direct sound and delay sound. Connect this to your

guitar amp or eect unit.

* If a device is connected to the DIRECT OUT jack, only

the delay sound is output.

CHECK indicator

Indicates the on/o status of the eect or the short loop function, and also provides a battery check

function. The indicator is lit red when on, and unlit when o.

* When operating on battery power only, the unit’s indicator will become dim when battery power gets too low.

Replace the battery as soon as possible.

[FEEDBACK] knob

Adjusts the feedback level. Turning the knob clockwise increases

the number of repetition of delay sound. Turning the knob fully

counterclockwise produces single delay sound.

Thumbscrew

When the thumbscrew is loosened, the

pedal will open, allowing you to change

the battery.

* A battery was installed in the unit before

it left the factory. The life of this battery

may be limited, however, since its primary

purpose was to enable testing.

[MODE] knob, [TIME] knob

Use the [MODE] knob to choose the mode.

When MODE = S. 50ms, M. 200ms, L. 800ms

Switches the delay time range between three settings. Use the [TIME]

knob to adjust the delay time. Turning the knob clockwise lengthens

the delay time.

MODE Minimum value Maximum value

S. 50ms 12.5 msec 50 msec

M. 200ms 50 msec 200 msec

L. 800ms 200 msec 800 msec

When MODE = SHORT LOOP

The sound immediately prior to pressing the pedal switch is played as

a loop as long as you hold down the pedal switch (short loop function).

Use the [TIME] knob to adjust the loop time (200–800 msec).

* If you change the loop time while the loop is playing, the pitch of the loop

sound changes.

DIRECT OUT jack

Outputs the direct sound. Connect this to your guitar amp, etc.

* Delay sound is output from the OUTPUT Jack.

[E.LEVEL] knob

Adjusts the volume of the delay sound. Turning the knob clockwise

increases the delay sound. If the knob is turned all the way clockwise,

the delay sound has the same volume as the direct sound.

If the knob is turned all the way counterclockwise, no delay sound is

output.

DC IN jack

Accepts connection of an AC Adaptor (sold separately: PSA series). By using an AC Adaptor,

you can play without being concerned about how much battery power you have left.

* We recommend that you keep batteries installed in the unit even though you’ll be powering it

with the AC adaptor. That way, you’ll be able to continue a performance even if the cord of the

AC adaptor gets accidentally disconnected from the unit.

* Use only the specied AC adaptor (PSA series).

* If the AC adaptor is connected while power is on, the power

supply is drawn from the AC adaptor.

Panel Descriptions

* 5 1 0 0 0 6 7 6 6 9 - 0 1 *

Pedal switch

Turns the eect or the short loop function on/o.

When setting the delay time to match the tempo of your song (tempo

delay), this is used to enter the tempo.

TEMPO jack

Connect a footswitch (sold separately: FS-5U, FS-6, FS-7). You can use a footswitch to enter the tempo.

* Only one footswitch can be connected. If you’re using the FS-6/FS-7, connect either the A jack or the B jack.

* Make this connection using a 1/4” plug cable (1/4” phone plug ,1/4” phone plug).

* Set the mode/polarity switches as shown in the illustration below.

FS-5U FS-6 FS-7

B A

Precautions When Connecting

5 To prevent malfunction and equipment failure, always turn

down the volume, and turn o all the units before making any

connections.

5 Do not use connection cables that contain a built-in resistor.

5 Once everything is properly connected, be sure to follow the

procedure below to turn on their power. If you turn on equipment

in the wrong order, you risk causing malfunction or equipment

failure.

When powering up

Turn on the power to your guitar amp last.

When powering down

Turn o the power to your guitar amp rst.

5 Before turning the unit on/o, always be sure to turn the volume

down. Even with the volume turned down, you might hear some

sound when switching the unit on/o. However, this is normal and

does not indicate a malfunction.

About Output

7 Connect to the OUTPUT jack only

The direct sound + delay sound is output.

DD-3T

7 Connect to the OUTPUT jack and the DIRECT OUT jack

The delay sound is output from the OUTPUT jack, and the direct

sound is output from the DIRECT OUT jack.

DD-3T

Direct soundDelay sound

7 Connect to the SEND/RETURN jacks of a guitar amplier

If you’re using this unit in a parallel-connected eect loop, insert a

dummy plug into the DIRECT OUT jack so that only the delay sound

is output to the RETURN jack.

RETURN

Dummy plug

SEND

INPUT

DD-3T

Using the Tempo Delay

By pressing the pedal switch or an external footswitch several times

in rhythm with your song, you can set the delay time to match the

tempo of the song (tempo delay)

MEMO

5 The delay time range is 133–800 msec (BPM = 75–300).

5 The delay time specied by tempo input is maintained until you operate

the [TIME] knob.

Using the pedal switch

* If a footswitch (sold separately) is connected to the TEMPO jack, you

can’t use the pedal switch to enter the tempo.

1. Use the [MODE] knob to specify the note value that will be the

basis of the delay time.

MODE Note length

S. 50ms Quarter note triplet

M. 200ms Dotted eighth note

L. 800ms Quarter note

2. Hold down the pedal switch for two seconds or longer.

The CHECK indicator is lit green, and now you can use the pedal

switch to enter the tempo.

* Tempo entry is not possible if the [MODE] knob is set to “SHORT LOOP.”

3. Press the pedal switch at quarter-note intervals in

synchronization with the tempo of the song.

According to the tempo that you enter, the delay time is set so

that it is the length of the note value that you specied with the

[MODE] knob.

The CHECK indicator blinks at the specied tempo.

4. To nish inputting the tempo, hold down the pedal switch for

two seconds or longer.

Using an external footswitch

Basic operation is the same as when using the pedal switch.

1. Connect a footswitch (sold separately: FS-5U, FS-6, or FS-7) to

the TEMPO jack.

2. Use the [MODE] knob to specify the note value that will be the

basis of the delay time.

3. Press the footswitch at quarter-note intervals in synchronization

with the tempo of the song.

The delay time is set, and the CHECK indicator blinks at the

specied tempo.

Changing the Battery

* Batteries should always be installed or replaced before connecting any

other devices. This way, you can prevent malfunction and damage.

* If you handle batteries improperly, you risk explosion and uid leakage.

Make sure that you carefully observe all of the items related to batteries

that are listed in “USING THE UNIT SAFELY” and “IMPORTANT NOTES”

(supplied on a separate sheet).

Thumbscrew

Battery housing

Pedal

Spring base

Coil spring

Guide bush hole

Battery snap cord

Battery snap

9 V battery

1. Hold down the pedal and loosen the thumbscrew, then open

the pedal upward.

2. Remove the old battery from the battery housing, and remove

the snap cord connected to it.

3. Connect the snap cord to the new battery, and place the

battery inside the battery housing.

* Be sure to carefully observe the battery’s polarity (+ versus –).

4. Slip the coil spring onto the spring base on the back of the

pedal, and then close the pedal.

* Carefully avoid getting the snap cord caught in the pedal, coil spring,

and battery housing.

5. Finally, insert the thumbscrew into the guide bush hole and

fasten it securely.

Main Specication

BOSS DD-3T: Digital Delay

Nominal Input Level -20 dBu

Input Impedance 1 MΩ

Nominal Output Level -20 dBu

Output Impedance 1 kΩ

Recommended Load

Impedance 10 kΩ or greater

Power Supply

Carbon-zinc battery (9 V, 6F22) or Alkaline battery

(9 V, 6LR61)

AC adaptor (PSA series: sold separately)

Current Draw

45 mA

Expected battery life under continuous use

Alkaline Approx. 11.5 hours

Carbon Approx. 3 hours

* These gures will vary depending on the actual

conditions of use.

Dimensions 73 (W) x 129 (D) x 59 (H) mm

2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches

Weight

(including battery)

420 g

15 oz

Accessories

Owner’s Manual, Leaet (“USING THE UNIT SAFELY,”

“IMPORTANT NOTES,” and “Information”), Alkaline

battery (9 V, 6LR61)

Options

(sold separately)

AC adaptor: PSA series

Footswitch: FS-5U, FS-6, FS-7

* 0 dBu = 0.775 Vrms

* This document explains the specications of the product at the time that

the document was issued. For the latest information, refer to the Roland

website.

AC adaptor (sold

separately: PSA series)

Electric guitar

Guitar amplier

Footswitch

(FS-5U etc.)

Model Name :

Type of Equipment :

Responsible Party :

Address :

Telephone :

DD-3T

Guitar Eects

Roland Corporation U.S.

5100 S. Eastern Avenue Los Angeles, CA 90040-2938

(323) 890-3700

SUPPLIER’S DECLARATION OF CONFORMITY

Compliance Information Statement

For the USA

Product specificaties

Merk:	Boss
Categorie:	Niet gecategoriseerd
Model:	DD-3T
Kleur van het product:	Beige
Gewicht:	420 g
Breedte:	73 mm
Diepte:	129 mm
Hoogte:	59 mm
Gebruikershandleiding:	Ja
Type stroombron:	AC, Battery
Accu/Batterij voltage:	9 V
Ondersteund aantal accu's/batterijen:	1
Aansluiting voor netstroomadapter:	Ja
Non-slip surface:	Ja
Stroomverbruik:	45 mA
Beste gebruik:	Gitaar
Type product:	Expressiepedaal
Synchronisatie ingangsimpedantie:	1000000 Ohm
Uitgang van 6,35 mm (1/4-inch):	2
Output impedance:	1000 Ohm
Ingang van 6,35 mm (1/4-inch):	2
Uitgangsniveau:	-20/0 dB
Nominale input level:	-20 dB
Status-indicatorlichtje:	Ja