Boss CS-3 Handleiding

Boss Niet gecategoriseerd CS-3

Lees hieronder de 📖 handleiding in het Nederlandse voor Boss CS-3 (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

Owner’s Manual

Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).

After reading, keep the document(s) where it will be available for immediate reference.

INPUT jack

This jack accepts input signals (coming from a guitar, some other musical

instrument, or another eects unit).

* The INPUT jack also serves as the power

switch. Power is turned on whenever

a plug is inserted into the INPUT jack,

and is turned o when the plug is

disconnected. When not using the

unit, you should disconnect any cord

connected to the INPUT jack.

AC Adaptor

(PSA series; sold separately)

Electric Guitar

English

LEVEL knob

This adjusts the volume of the eect sound.

* When this knob is turned counterclockwise, no sound will be heard.

The BOSS CS-3 is a compression sustainer that produces long sustain without distorting the original sounds.

The attack volume adjusts picking forth widely and provides any drive-sound.

As having the tone control function, the CS-3 allows wider variation of sound creation.

More-over, featuring the wide range of maximum input level and compression, the CS-3 can be used as an ordinary limiter by turning down the sustain volume.

OUTPUT jack

The output jack is used to connect the unit to

ampliers or other devices.

Guitar Amplier

DC IN jack

Accepts connection of an AC Adaptor (PSA series; sold separately). By using an AC Adaptor, you can play

without being concerned about how much battery power you have left.

* We recommend that you keep batteries installed in the unit even though you’ll be powering it

with the AC adaptor. That way, you’ll be able to continue a performance even if the cord of the

AC adaptor gets accidentally disconnected from the unit.

* Use only the specied AC adaptor (PSA-series).

* If the AC adaptor is connected while power is on, the power supply is

drawn from the AC adaptor.

CHECK indicator

This indicator shows whether an eect is ON/OFF, and doubles as the Battery Check indicator.

The indicator lights when an eect is ON.

* If this indicator goes dim or no longer lights while an eect is ON, the battery is near

exhaustion and should be replaced immediately.

* The CHECK indicator shows whether the eect is on or o, and indicates the dierent

functions. It does not indicate whether the power to the device is on or not.

TONE knob

This adjusts the tone of sound. Rotating it clockwise will create sharp sound with

emphasized treble, while turning it counterclockwise will create soft sound with

cut treble.

Pedal Switch

This switch turns the eects ON/OFF.

Thumbscrew

When this screw is loosened, the pedal will open, allowing you to change the

battery.

* For instructions on changing the battery, refer to “Changing the

Battery.”

Panel Descriptions

Main Features

Operating the Unit

1. After marking all the

connections, set the panel

as shown right.

2. Press the Pedal Switch. If the indicator lights

up, the eect is on, and if not, the eect is o.

This indicator also serves as battery check. Is it becomes dimmer or

does not light as all, battery replacement is required.

3. Rotate the

SUSTAIN knob to

an appropriate

position.

* As you turn the Sustain

knob clockwise, you may

hear noise or howling.

If so, rotate it slightly

counterclockwise.

4. Press the Pedal Switch to turn the eect on

(LED on), and adjust the volume of the eect

sound using the LEVEL knob.

5. Adjust the intensity of the attack with the

ATTACK knob.

6. Adjust the tone using the TONE knob.

Use of Battery

* A battery was installed in the unit before it left the factory. The life of

this battery may be limited, however, since its primary purpose was to

enable testing.

* If you handle batteries improperly, you risk explosion and uid leakage.

Make sure that you carefully observe all of the items related to batteries

that are listed in “USING THE UNIT SAFELY” and “IMPORTANT NOTES”

(supplied on a separate sheet).

* When operating on battery power only, the unit’s indicator will become

dim when battery power gets too low. Replace the battery as soon as

possible.

* Batteries should always be installed or replaced before connecting any

other devices. This way, you can prevent malfunction and damage.

Changing the Battery

1. Hold down the

pedal and loosen

the thumbscrew,

then open the

pedal upward.

* The pedal can be

opened without

detaching the

thumbscrew

completely.

2. Remove the old

battery from the

battery housing,

and remove the snap cord connected to it.

3. Connect the snap cord to the new battery, and place

the battery inside the battery housing.

* Be sure to carefully observe the battery’s polarity (+ versus -).

4. Slip the coil spring onto the spring base on the back of

the pedal, and then close the pedal.

* Carefully avoid getting the snap cord caught in the pedal, coil

spring, and battery housing.

5. Finally, insert the thumbscrew into the guide bush

hole and fasten it securely.

Main Specications

BOSS CS-3: Compression Sustainer

Nominal Input Level -20 dBu

Input Impedance 1 MΩ

Nominal Output Level -20 dBu

Output Impedance 1 kΩ

Recommended Load

Impedance

10 kΩ or greater

Power Supply DC 9 V; Dry battery 6F22 (9 V) type (carbon)/

Dry battery 6LR61 (9 V) type (alkaline) AC

Adaptor (PSA-series: optional)

Current Draw 20 mA

* Expected battery life under continuous use:

Carbon: 10.5 hours, Alkaline: 26 hours

These gures will vary depending on the

actual conditions of use.

Dimensions 73 (W) x 129 (D) x 59 (H) mm

2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches

Weight 380 g / 14 oz (including battery)

Accessories Owner’s Manual, Leaet (“USING THE UNIT

SAFELY,” “IMPORTANT NOTES,” and “Informa-

tion”), Dry battery/9 V type (6F22)

Options AC adaptor (PSA-series)

* 0 dBu = 0.775 Vrms

* This document explains the specications of the product at the

time that the document was issued. For the latest information,

refer to the Roland website.

Using the CS-3

as a compressor

Using the CS-3

as a limiter

Thumbscrew

Battery Housing

Pedal

Spring Base

Coil Spring

Guide Bush

Hole

Battery Snap

Cord

Battery

Snap

9 V Battery

* To prevent malfunction and equipment failure, always turn down the volume, and turn o all the units before

making any connections.

* Before turning the unit on/o, always be sure to turn the volume down. Even with the volume turned down, you

might hear some sound when switching the unit on/o. However, this is normal and does not indicate a malfunction.

* Avoid using the CS-3 in extreme heat, humidity or where it may be aected by dust.

ATTACK knob

This adjusts the intensity of the attack in the picking.

At its clockwise position, the attack sound is retained in each note even in fast

picking, creating drive sound.

SUSTAIN knob

This knob adjusts the sustain time. Rotating this knob clockwise increases

the sustain time. By rotating it counterclockwise, the output level is limited,

therefore the CS-3 works as a limiter.

* 5 1 0 0 0 6 9 0 2 9 - 0 1 *

Product specificaties

Merk:	Boss
Categorie:	Niet gecategoriseerd
Model:	CS-3
Kleur van het product:	Black, Blue
Gewicht:	380 g
Breedte:	73 mm
Diepte:	129 mm
Hoogte:	59 mm
Gebruikershandleiding:	Ja
Type stroombron:	AC, Battery
Accu/Batterij voltage:	9 V
Ondersteund aantal accu's/batterijen:	1
Aansluiting voor netstroomadapter:	Ja
Non-slip surface:	Ja
Stroomverbruik:	20 mA
Beste gebruik:	Gitaar
Type product:	Expressiepedaal
Synchronisatie ingangsimpedantie:	1000000 Ohm
Uitgang van 6,35 mm (1/4-inch):	1
Output impedance:	1000 Ohm
Ingang van 6,35 mm (1/4-inch):	1
Uitgangsniveau:	-20/0 dB
Nominale input level:	-20 dB
Status-indicatorlichtje:	Ja