Boss BPLCAM Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Boss BPLCAM (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 22 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
REAR VIEW MOTORCYCLE
LICENSE PLATE MOUNT CAMERA
FEATURING HIDDEN MOUNTING BRACKET
BPLCAM
USER’S MANUAL
BOSS Audio Systems
3451 Lunar Court • Oxnard, CA 93030
www.bossaudio.com
805-751-4853 Customer Service
Tech Support: www.bossaudio.com/support
0121
DO NOT FULLY RELY ON REVERSE CAMERA
WHEN BACKING UP.
ALWAYS CHECK YOUR SURROUNDINGS
BEFORE BACKING UP.
SPECIFICATIONS
Power Supply DC 12v
Lens Angle (Deg.) 17
TV System NTSC
Video Output 1.0vp-p, 75
S/N Ratio < 48 dB
IP Rating IP68
Operating Temp. (Deg. C) -30ºC ~ +70ºC (RH 95% Max.)
White Balance Auto
Minimum Illumination 0.5 LUX
AGC Auto
Resolution (TV Lines) 480
Electronic Shutter 1/60 (NTSC)
Eective Pixels 628 x 586
Above parameters can be modified without notification.
TROUBLESHOOTING GUIDE
The following checklist might help to solve the problems when
using this unit. Please double check to ensure connection and
procedure of operation is done properly before using checklist.
PROBLEM CAUSE/SOLUTION
NO IMAGE Check that power cable is securely connected.
Check to ensure there is a good connection
between video-in and monitor.
Check that REVERSE GEAR is engaged.
Check to ensure correct monitor setup.
IMAGE BLURRING Check for water/water stain or dust on
camera lens.
Clean camera lens
IMAGE SHAKING Check to insure camera is mounted and
secured tightly.
IMAGE SLANTED Adjust camera mounting bracket
INSTALLATION
Complete all required connections so that all lines are
hidden in vehicle.
Power/Video
Red and black back lights 12V line
Camera
DC 12V
DC 12V
VIDEO
NOTE:
If problems persist – consult nearest service dealer. DO NOT attempt
to disassemble or modify unit.
1. WIRE CONNECTION
2. CAMERA INSTALLATION
Camera should be installed in the following configuration:
License Plate Frame Mount – Align camera frame with top-set of
screw holes on license plate or license plate frame. Affix camera
using license plate mount screws. See: (diagram 1)
Attention: The camera switch is controlled by reverse gear shift.
3. TO REMOVE THE DISTANCE GUIDE LINES (Optional):
1. Turn the system OFF before proceeding.
2. Cut the white loop wire located at the connection points
(camera end).
3. Insulate the wire, using tape or crimp connectors on both ends.
4. Reconnecting the wire will display the guide lines again.
4. TO INVERT CAMERA IMAGE:
1. Turn the system OFF before proceeding.
2. Cut the blue loop wire located at the connection points (camera end).
3. Insulate the wire, using tape or crimp connectors on both ends.
4. Reconnecting the wire will orient the image back to its original
position.
License Plate
Frame
(diagram 1)


Product specificaties

Merk: Boss
Categorie: Niet gecategoriseerd
Model: BPLCAM

Heb je hulp nodig?

Als je hulp nodig hebt met Boss BPLCAM stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Boss

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Electrolux

Electrolux STA9 Handleiding

23 November 2024
Electrolux

Electrolux UMP3 Handleiding

23 November 2024
Bosch

Bosch HEZ8TK36UC Handleiding

23 November 2024
Bosch

Bosch HEZ8ZZ36UC Handleiding

23 November 2024
Bosch

Bosch HDZIT301 Handleiding

23 November 2024
Bosch

Bosch HEZBS301 Handleiding

23 November 2024
LG

LG LX-330 Handleiding

23 November 2024
Bosch

Bosch KSZ2AVU00 Handleiding

22 November 2024