Bontrager Duo Trap S Sensor Handleiding

Bontrager Fietscomputer Duo Trap S Sensor

Lees hieronder de 📖 handleiding in het Nederlandse voor Bontrager Duo Trap S Sensor (2 pagina's) in de categorie Fietscomputer. Deze handleiding was nuttig voor 53 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

About this product

IMPORTANT: To use the RIDEtime Elite computer, you must have an ANT+ compatible speed, cadence,

or power sensor mounted on your bicycle.

Compatible sensors:

• Bontrager Duo Trap – PN 508126

• Bontrager Duo Trap S – PN 437960

• Bontrager Interchange Combo – PN 438482

• Bontrager ANT+/BLE Softstrap Heart Rate Belt Kit – PN 519606

• Other ANT+ compatible sensor

To set up any other sensor, please refer to the manual that came with your sensor.

When riding your bicycle, do not stare at the computer for a long time. If you do not watch the road,

you could hit an obstacle which might cause you to lose control, fall, and cause injury.

WARNING

Bontrager

RIDEtime Elite Computer

plus

Duo Trap S Sensor

www.bontrager.com

PN 580968

Parts list

RIDEtime Elite Computer

1 2

Install battery

Install computer mount

1. Shim use: Determine the diameter of your handlebar.

• Use the thin shim with a 31.8mm handlebar.

• Use the thick shim with a 25.4 or 26.0mm handlebar.

• Use no shims with a 35mm handlebar.

• Use both shims with a 22.2mm handlebar.

2. Remove the rubber cover over the mounting clamp bolt.

3. Use a 2.5mm hex wrench to torque the bolt to 0.8 N-m (7 in-lb).

4. Replace the rubber cover over the clamp bolt.

NOTE: The mount is not to be used with a cell phone.

Mount computer

Understanding the instructions

Button

location

Quick

press

Multi

press

Long press

(2 seconds)

Front

Rear

•

1•

•

Duo Trap S

1. Gasket (alloy bikes)

2. Sensor with grommet and 2mm spacer

installed (carbon bikes)

3. 8mm bike mounting screw

4. Speed magnet (wheel)

5. CR2032 battery

6. Cadence band shim

7. Large cadence band (crank) (26mm)

W519998

8. Small cadence band with magnet

(crank) (9mm) W519999

9. Xsmall cadence band with magnet

(crank) (4mm) W534154

10. Plug (large cadence band)

8107

3 4

Install battery

Install Duo Trap S sensor (alloy bikes)

1. Remove the Duo Trap S cover from the chainstay.

2. Remove the grommet from the sensor.

3. Install the gasket onto the sensor with the notch facing forward as shown.

4. Install the sensor and gasket into the chainstay.

5. Hold the sensor into place and install the 8mm screw.

6. Use a 2.5mm hex tool to tighten the sensor.

Install Duo Trap S sensor (carbon bikes)

1. Remove the Duo Trap S cover from the chainstay.

2. Remove the grommet from the sensor.

3. Fully insert the grommet into the chainstay. Make sure the grommet is ﬂush with the chainstay.

4. Install the sensor into the grommet in the chainstay.

HINT: Hold the grommet in place with one hand and insert the sensor with the other hand as shown.

5. Hold the sensor in place and use a 2.5mm hex to install and tighten the 8mm screw.

NOTE: Make sure the 2mm spacer is installed in the grommet before you tighten the screw.

Mount speed magnet

1. Tighten the speed magnet on a spoke

2. Align the speed magnet with the marking on the sensor.

3. If necessary, rotate the magnet 90˚ or 180˚ to achieve sensor clearance.

4. Rotate the wheel and look for a red LED in the sensor to verify the magnet and sensor are in

alignment.

NOTE: The LED will illuminate for the ﬁrst 10 revolutions only.

Install small cadence magnet

1. Remove the non driveside pedal and install the small cadence magnet on the crank arm with the thick

side nearest to the chainstay.

2. Align the magnet with the sensor.

• Alloy bikes: Align the magnet with the line on the sensor.

• Carbon bikes: Place the magnet 135mm or 145mm from the center of the bottom bracket to the

center of the magnet

3. Rotate the crank backwards. Look for the green LED on the cadence sensor to verify the magnet is

correctly aligned.

NOTE: The LED will illuminate for the ﬁrst 10 revolutions only.

4. Optional: If the magnet is aligned but the LED does not illuminate, place a cadence band shim

underneath the appropriate magnet.

5. If the small band does not ﬁt between the crank and the chainstay, use the XS (4mm) cadence

band provided.

Install large cadence magnet

1. Remove the plastic cap from inside the small cadence band.

2. Remove the magnet from inside the small cadence band.

3. Insert the magnet fully inside the large cadence band so it is ﬂush against the inside of the cavity.

4. Insert the plastic plug into the cavity of the large cadence band to hold the magnet in place.

5. Follow the steps in the Small cadence magnet installation to complete this installation.

•

1•

•

4•

m2.5N

•

4•

4a •

4b •

2.5Nm

•

90˚ 180˚

•

a•

b•

•

2145mm

135mm

•

3•

•

1•

2•

•

4•

Selection note:

Grey color represents

ﬂashing characters that

show selected value.

Shows number of digits

to be set.

Screen icon Description

Speed sensor is connected.

Flashing if searching for sensor.

Cadence sensor is connected.

Flashing if searching.

Heart rate monitor is connected.

Flashing if searching.

Power meter is connected.

Flashing if searching.

A service interval has been

reached. Flashing is a prompt

to clear.

Transmitter signal when

connected to compatible lights.

Flashing if searching.

Battery life is sufﬁcient.

Replacement when only

1/3 indicated.

BPM

RPM

KPH

MPH

Enter and exit setup modes

Front button

Rear button

AC button

Road Mountain City

Size Code Size Code Size Code

700:23* 2124 29:2.2* 2340 700:28* 2164

700:25 2136 29:2.3 (2.35) 2359 700:32 2190

700:28 2164 29:3.0 2413 700:35 2209

700:32 2190 27.5:2.2 2221 700:38 2227

700:35 2209 27.5:2.4 2253 700:40 2240

700:38 2227 27.5:2.8 2309 700:42 2253

700:40 2240 27.5:3.8 2400 700:45 2271

700:42 2253 27.5:4.5 2485 26:2.0 2117

700:45 2271 26:2.0 2117 26:2.2 2148

Custom 001-2999 26:2.2 2148 Custom 01-2999

26:3.8 2322

26:4.7 2403

Custom 01-2999

*Default

The letters indicate the order in which to

push the buttons.

More than one arrow means you should

push the button until you see the value

you want.

Press and hold until next digit ﬂashes to

switch to next digit or ﬁeld.

1. Computer

2. Battery cover

3. 31.8mm handlebar shim

4. Out front mount

5. CR2032 battery

6. 22.2, 25.4 & 26.0mm handlebar shim

Rear button

• Press the rear button once to enter

Primary setup.

• Press and hold the rear button 5 seconds

to enter Pairing and Advanced setup.

• Press the rear button for 5 seconds to

exit either setup mode.

• In Ride mode you can press the rear

button for 5 seconds to return you to the

beginning of the Primary setup without

changing any previously entered settings.

NOTE: Do not use the rear button while riding.

It will restart setup mode.

Primary setup

CUSTOM

BPM

RPM

KPH

MPH

BPM

RPM

KPH

MPH

Press and hold until number

ﬂashes to switch between

hours and minutes.

BPM

RPM

KPH

MPH

3...

BPM

RPM

KPH

MPH

Eng

Deu

Fra

Esp

BPM

RPM

KPH

MPH

BPM

RPM

KPH

MPH

Road

Mtb

City

BPM

RPM

KPH

MPH

24 Hr

12 Hr

BPM

RPM

KPH

MPH

BPM

RPM

KPH

MPH

BPM

RPM

KPH

MPH

BPM

RPM

KPH

MPH

3...

BPM

RPM

KPH

MPH

3...

NOTE: Custom wheel size

is the circumference of the

wheel in mm. See Wheel

size chart.

AC button

• Press the AC button for a ‘hard reset’ to return the computer to the factory default settings.

Front button

• Press the front button to scroll through the screens to ﬁnd your desired setting.

Measure your wheel size

1. With the valve stem of the wheel directly over the ﬂoor, mark the ﬂoor at the valve stem.

2. Roll the bike forward one revolution of the wheel so that the valve stem is again directly over the ﬂoor.

3. Mark the new location of the valve stem.

4. Measure the distance between the marks. Measurements in mm are required.

BPM

RPM

KPH

MPH

BPM

RPM

KPH

MPH

OFF

1 Hr

3 Hr

6 Hr

...24 Hr

NOTE: If you have no paired sensors, you’ll

be taken to Pairing and Advanced setup upon

completion of Primary setup.

NOTE: When Auto Clear is set, the number

represents the amount of inactive time before the

last ride’s data is cleared.

Pairing and Advanced setup

Pairing NOTES:

1. If you select ALL, the computer will look to pair

all nearby devices. If you want to look for a

speciﬁc type of sensor (speed, cadence, heart

rate, or power) then select that choice.

2. If you want to pair more than one sensor but

not all, pair one sensor at a time. Repeat the

procedure for each sensor.

3. To exit and advance to the Pair lights step,

press the rear button.

BPM

RPM

KPH

MPH

BPM

RPM

KPH

MPH

ALL

Speed

Cadence

Heart

Power

Power meter calibration (If power meter sensor is not paired, computer will advance to step 5.)

Follow the power meter guidelines to calibrate your power meter for the most accurate reading.

NOTE: Symbols ﬂash during search and become steady once found.

You can exit pairing, and advance to the next step once the desired

symbols stop ﬂashing. Otherwise the system will advance in 30 seconds.

BPM

RPM

KPH

MPH

BPM

RPM

KPH

MPH

12380

40277

...

BPM

RPM

KPH

MPH

BPM

RPM

KPH

MPH

NOTE: These are paired sensor ID’s.

BPM

RPM

KPH

MPH

BPM

RPM

KPH

MPH

BPM

RPM

KPH

MPH

Retry

Pair lights

Yes

BPM

RPM

KPH

MPH

Yes

BPM

RPM

KPH

MPH

6NOTES:

If Auto Lights is enabled (YES):

1. The computer will turn your paired light(s) on when speed is detected

above 3 mph.

2. The lights will remain on until speed drops below 1 mph for longer than 3

minutes.

3. The computer will not override:

• Manual input to the lights.

• Input from a light pairing with another computer or a

remote control.

If Auto Lights is disabled (NO):

4. The paired light(s) will remain stored as saved connections.

5. The computer does not try to form a connection with the lights.

There are three occurrences when a command is sent to the lights to change their settings:

• Turn ON when speed above 3 mph is detected.

• Turn OFF when speed below 1 mph is detected for longer than 3 minutes.

• Change mode when Night mode state is changed.

Light setting

NOTES:

1. The computer should turn the lights ON to the appropriate mode based on whether Night Mode is

enabled or disabled.

2. See light mode table in Night mode section.

3. In ride mode, if the battery level of a connected light reaches critically low, the transmitter icon will ﬂash

and the display will ﬂash LOW BATTERY LIGHTS (low batt! in the middle display and LIGHTS in the

lower display).

Low battery detection

In ride mode, if the battery level reaches critically low:

• The transmitter icon will ﬂash continuously and the display will show LOW BATTERY LIGHTS

for 2.5 seconds.

• The LOW BATTERY LIGHTS message will be repeated every 30 seconds.

Display

NOTES:

• These screens will be displayed only if Dual View was selected (YES) in step 9.

• If NO is selected in any of the display screens in step 8, that metric will not be available in the

Scan display.

BPM

RPM

KPH

MPH

Yes

BPM

RPM

KPH

MPH

Yes

BPM

RPM

KPH

MPH

Yes

BPM

RPM

KPH

MPH

Yes

BPM

RPM

KPH

MPH

Yes

BPM

RPM

KPH

MPH

BPM

RPM

KPH

MPH

Speed

Cadence

Heart

Power

BPM

RPM

KPH

MPH

Yes

BPM

RPM

KPH

MPH

Yes

BPM

RPM

KPH

MPH

Yes

BPM

RPM

KPH

MPH

Yes

BPM

RPM

KPH

MPH

Speed

Cadence

Heart

Power

Speed

Cadence

Heart

Power

BPM

RPM

KPH

MPH

Ride mode

To wake the computer: Push any button or spin the wheel.

The default Ride mode is shown with all sensors connected, and Speed is selected as the primary metric.

Sensors that are not connected or that are disabled will not be displayed and will be skipped.

The computer will turn off after 10 minutes of inactivity.

NOTE: If you do not have a speed sensor, the timer will still run if you have a cadence sensor or power

meter.

To reset the timer, hold down the front button for 5 seconds from any Ride mode screen.

Night mode

BPM

RPM

KPH

MPH

BPM

RPM

KPH

MPH

BPM

RPM

KPH

MPH

BPM

RPM

KPH

MPH

Distance Dual View

(only if Dual View is on)

Avg Max

(speed)

BPM

RPM

KPH

MPH

BPM

RPM

KPH

MPH

BPM

RPM

KPH

MPH

Cadence Avg Max

(cadence)

Heart Rate

BPM

RPM

KPH

MPH

BPM

RPM

KPH

MPH

BPM

RPM

KPH

MPH

Avg Max

(heart rate)

Power Avg Max

(power)

BPM

RPM

KPH

MPH

BPM

RPM

KPH

MPH

BPM

RPM

KPH

MPH

Calories Odometer Clock

BPM

RPM

KPH

MPH

BPM

RPM

KPH

MPH

BPM

RPM

KPH

MPH

Scan

(if enabled)

If the wrench icon is

displayed, advance

to this screen,

otherwise return to

Ride mode.

Back to Ride

mode

Yes

Press the front button for 5

seconds to prompt the clear

data question.

Off

BPM

RPM

KPH

MPH

Trek Bicycle Corporation

Contact information:

North America

Trek Bicycle Corporation

801 West Madison Street

Waterloo, WI 53594

Tel: 800-313-8735

Europe

Bikeurope BV

Ceintuurbaan 2-20C

3847 LG Harderwijk

The Netherlands

Tel: +31 (0)33 45 09 060

Statements of regulatory compliance

FCC Compliance

RIDEtime Elite Computer – FCC ID: O4GRTELITE

IC: 7666A-RTELITE

Duo Trap S – FCC ID: O4GDUOTRAPS

IC: 7666A-DUOTRAPS

Transmission Frequency: 2.4GHz

Bluetooth: 2402MHz ~ 2480MHz

ANT+: 2457MHz

Bluetooth Max Power: <6dBm

ANT+ Max Power: <6dBm

Operating power: 3 V D C

Operating temperature: 0ºC ~50ºC

These devices comply with part 15 of the FCC Rules.

RF exposure compliance distance is 20 millimeters.

Operation is subject to the following conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that may cause

undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

— Consult the dealer or experienced radio / TV technician for help.

CAUTION: Any changes or modiﬁcations not expressly approved by Trek Bicycle Corporation could void

the user’s authority to operate the equipment.

NOTES: TREK BICYCLE CORPORATION IS NOT RESPONSIBLE FOR ANY RADIO OR TV

INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT.

Industry Canada Compliance

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not cause interference, and (2) this device must accept any

interference, including interference that may cause undesired operation of the device.

Leprésent appareil est conforme aux CNR d’Industrie Canada applicable aux appareils radio. Exempts

de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire

de brouillage, et (2) l’utilsateur de l’appareil doit accepter tout brouillage radioélectrque subi, meme si le

brouillage est susceptible d’en compromettre le fonctionnement.

This Bontrager equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled

environment. The radiated output power of the Transmitr Wireless Device is below the Industry Canada (IC)

radio frequency exposure limits. This transmitter must not be co-located or operating in conjunction with

any other antenna or transmitter.

Status of the listing in the Industry Canada’s REL (Radio Equipment List) can be found at the following web

address: http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do?lang=eng

Additional Canadian information on RF exposure also can be found at the following web address:

http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html

Cet appareil est conforme aux limites d’exposition à la fréquence radio (FR) d’IC et de FCC. La puissance

de sortie émise par l’appareil de sans ﬁl Transmitr est inférieure à la limite d’exposition aux fréquences radio

d’Industry Canada (IC). Cet appareil est en contact direct avec l’utilisateur dans des conditions normales

d’utilisation. L’émetteur ne doit pas être co-implémenté ou utilisé conjointement avec une autre antenne ou

un autre émetteur.

Ce périphérique est homologué pour l’utilisation au Canada. Pour consulter l’entrée correspondant

à l’appareil dans la liste d’équipement radio (REL - Radio Equipment List) d’Industry Canada

rendezvous sur: http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do?lang=fraPour des

informations supplémentaires concernantl’exposition aux RF au Canada rendezvous sur:

http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html

European Union Compliance

Trek Bicycle Corporation and Bontrager hereby declare that the wireless devices identiﬁed as

RIDEtime Elite Computer and Duo Trap S Sensor are in compliance with the following European Directives:

• RED 2014/53/EU

• EMCD 2014/30/EU

• LVD 2014/35/EU

• RoSH Directive 2011/65/EU

The full text of the EU declaration of conformity is available from your bike shop, or at the following internet

address: http://www.bontrager.com/support

Enable lights (If lights are not paired, computer will advance to step 6.)

1. If Pair Lights is enabled (YES), the computer will enter search mode, and

the transmitter icon ( ) will ﬂash. Hold the computer close to the desired

light to be paired.

2. If a light is detected:

• The computer will display FOUND.

• The light sensor ID and the transmitter icon will display for

2.5 seconds.

• The light turns on for 2.5 seconds, then turns off.

3. The unit will continue to search for up to three lights. To exit the search,

press the rear button.

NOTE: If you accidentally pair a light, press the AC button to delete all lights.

Then pair to only the lights desired.

Press the front button for 10 seconds to prompt the Night mode OFF/ON question.

• Night mode will enable the backlight.

• In Night mode, the ﬁrst button press activates the backlight for 5 seconds and

does not advance the carousel.

• Each additional press extends the backlight for 5 seconds, and advances the

carousel.

• When Night mode is OFF, the backlight is disabled.

• If lights are connected, Night Mode setting will determine Light Mode.

When paired with Bontrager lights, the following table shows what mode the

lights are in:

Night Mode ON Night Mode OFF

Headlight Medium steady Day ﬂash

Taillight Night ﬂash Day ﬂash

Display customization

NOTE: Sensors disabled during step 10 will not show either the instantaneous screen or the

AVG/MAX screen.

BPM

RPM

KPH

MPH

All

Off

Custom

BPM

RPM

KPH

MPH

Yes

BPM

RPM

KPH

MPH

Yes

BPM

RPM

KPH

MPH

Yes

BPM

RPM

KPH

MPH

Yes

BPM

RPM

KPH

MPH

Yes

NOTES:

1. If you choose ALL, the computer will scan all metrics (Speed, Cadence, Heart rate, Power, Lights).

2. If you choose OFF, you will not have the option to scan.

BPM

RPM

KPH

MPH

Yes

BPM

RPM

KPH

MPH

Yes

BPM

RPM

KPH

MPH

Yes

BPM

RPM

KPH

MPH

Yes

BPM

RPM

KPH

MPH

Yes

BPM

RPM

KPH

MPH

Product specificaties

Merk:	Bontrager
Categorie:	Fietscomputer
Model:	Duo Trap S Sensor

Heb je hulp nodig?

Als je hulp nodig hebt met Bontrager Duo Trap S Sensor stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Fietscomputer Bontrager

Bontrager Trip wireless Handleiding

16 Augustus 2023

Bontrager Trip 1 Handleiding

16 Augustus 2023

Bontrager Duo Trap S Sensor Handleiding

16 Augustus 2023

Bontrager Node Handleiding

16 Augustus 2023

Bontrager Trip 2 Handleiding

16 Augustus 2023

Bontrager Duotrap Handleiding

13 Mei 2023

Bontrager Duotrap S Handleiding

6 Mei 2023

Bontrager Trip 100 Handleiding

2 Mei 2023

Bontrager Trip 5W Handleiding

27 April 2023

Bontrager Trip 300 Handleiding

27 Maart 2023

Handleiding Fietscomputer

Nieuwste handleidingen voor Fietscomputer

Cateye Commuter CC-COM10W Handleiding

21 December 2024

Lezyne Micro C Handleiding

15 November 2024

Pro phete BW 020 Handleiding

7 November 2024

Wahoo Elemnt Roam v2 Handleiding

23 September 2024

VDO R4 Handleiding

26 Juli 2024

VDO R5 Handleiding

26 Juli 2024

Sigma Eox View 1700 Handleiding

22 Juli 2024

Aplic 305673 Handleiding

16 Juli 2024

IGPSport BSC100 Handleiding

16 Juli 2024

IGPSport iGS800 Handleiding

15 Juli 2024