Blebox wlightbox Handleiding

Blebox Smarth home wlightbox

Lees hieronder de 📖 handleiding in het Nederlandse voor Blebox wlightbox (3 pagina's) in de categorie Smarth home. Deze handleiding was nuttig voor 9 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

SAFETY RULES

Connect only in accordance with the diagram presented in the

manual. Improper connections may be dangerous, it can damage

the controller, and loss of the warranty.

Do not connect loads with more than permissible power.

DANGER! Risk of electric shock! Even with the device turned o,

the outputs may be live. All assembly work should be ALWAYS

performed with the disconnected power circuit.

Connecting the device to a power supply that does not meet the

quality requirements specied in EN 50081-1, EN 50082-1, UL508,

EN 60950 will invalidate the warranty.

Disconnect the installation supply voltage before installing the controller.

Remember that any mounting works should be carried out when the mains

voltage is disconnected (switch o the mains fuse or disconnect the power

cord from the mains socket).

1INSTALLATION

CONNECTION DIAGRAMS

FIRST LED RGBW CONTROLLER BASED ON THE µWiFi TECHNOLOGY

LED controller

with μWiFi tecnology

wLightBox + 4-channel strip

12 - 24V max 12A, 3 A channel

R G B W

µWiFi LED RGBW controller wlightBox

LED STRIP

RGB+W max12A

110 / 230V

12-24V

power

supply

wLightBox + LED RGB strip + 1-color LED strip (white color)

LED STRIP

WHITE max 3A

12 - 24V max 12A, 3 A channel

R G B W

µWiFi LED RGBW controller wlightBox

LED STRIP

RGB+W max 9A

110 / 230V

12-24V

power

supply

wLightBox + 4 single-channel LED strip

12 - 24V max 12A, 3 A channel

R G B W

µWiFi LED RGBW controller wlightBox

LED STRIP max 3A

110 / 230V

12-24V

power

supply

Download the . If you have an Android mobile device, free wBox application

you will nd the application in the Play Store. For iOS devices the application

is in the App Store.

By using your mobile phone or tablet, connect it to the device wireless

network. To do this, enter to your smartphone or tablet settings, then go to

setting of the WiFi network and nd the network name "wLightBox-

-xxxxxxxxxx” where xxxxxxxxxx is the serial number of the device. Connect to

this network.

Turn on the wBox application. A device will appear at the top of the screen. To

add it to the application, click on "+" on the right side of the name. To pre-con-

gure the controller, click on the default device name.

2FIRST START

Go to settings ("Settings" icon in the upper right corner of the screen) and

select the correct option in the "Device type" eld depending on the LED strip

connected. You can choose between the options "RGBW" - for three-color

strips with additional white, "RGB" - for three-color strips and "MONO" - for

monochromatic strips or halogen bulbs. After saving the settings, go to the

main panel by clicking the arrow in the upper left corner. Test the controller

works- if you have a multi-colored tape, select color from the color selection

circle and set the brightness using the scrollbar. If you have monochrome

strip, select the brightness of the channel with the scrollbar. Test the

controller's work by moving the brightness scrollbar several times in the

extremes and intermediate positions - the light source should change its

brightness. The control panel also has an additional eects menu – the access

to it is achieved by moving-up the screen from the bottom ("More" at the

bottom of the screen). In the menu you can choose predened colors and set

the duration of the color, or choose a predened lighting eect and set the

transition times.

TECHNICAL SPECIFICATIONS

12 - 24V

< 1W

open drain, PWM,

low side control

39 x 35 x 20 mm

24V

288W

You can also set the conguration using the web browser

of your phone / tablet. After connecting to the wireless

network of the controller, turn on the browser and go

website www.blebox.eu

3ACCESS POINT AND WIFI NETWORK SETTINGS

Once you turn on the controller for the rst time, you can proceed to its

further conguration. Being connected to the WiFi network emitted by the

device, in the control panel of the wBox application select the device, then go

to “Settings” (icon at the top-right corner of the screen).

You can change the name of the device that is displayed in the wBox

application. In addition, you can change the name and password of its

generated WiFi network. Remember that changing the network name or

password will disconnect the device immediately after you click the "Save"

button, so re-connect to the device using the newly assigned network name

and password.

You can add the controller to your home WiFi network to control it through

this home network or from anywhere in the World. To do this, in the "Connect"

settings section, select a network name from the list and press "Connect". If is

required, enter the WiFi network password. During the connection of the

controller to your home network, the phone / tablet may disconnected from

the network. In this case, you will need to reconnect your phone / tablet to the

controller network.

Please remember that in order to control the device outside the local WiFi

network, from anyplace in the World by using the wBox application, the

option "Remote access enabled" in the controller settings must be set to "Yes".

Once you've nished conguring the WiFi network, you can disconnect your

phone/tablet from the controller network and connect your mobile device

directly to your home WiFi network. The control from the wBox application

will work the same way as when the phone / tablet is connected to the

controller network. If the user leaves the local network, for example, leaving

home or using the mobile data, the wBox application will signal this state as

"Remote mode". In this case, the devices can be controlled, but for security

reasons settings are not available.

The controller should be installed in a place protected against adverse

environmental conditions, protected from third party access - in the ush box

or inside the enclosure of the controlled device. It is recommended that the

device be mounted in a stable and xed position.

Familiarize yourself with the diagram and then proceed with the installation

of the controller. Pay special attention to the designation of the controller

connectors. Start by connecting the power wires: (+) (red or black with a white

dotted line) and (-) (black).

Connect the LED strip paying attention to the polarity. Depending on the use,

it is possible to connect a single RGBW strip, one RGB strip, an RGB strip with

a white strip or four monochromatic strips. The "+" cathode wire (usually

white color in multicolored strips or red in monochrome strips) must be

connected to the "+" connector of the controller, and the anode wire "-" (color

corresponding to each color of the LEDs in multi-color strips or white color

in monochrome strips) to the corresponding output, i.e. R, G, B or W. The

controller also allows to control halogen lamps, the polarity of the wiring is

not important.

After making sure that the device is connected in accordance with the

diagram and that there are no metal components near the controller which

may accidentally cause short-circuit, start the device by turning on the power

(turning on the mains fuse or connecting the power cord to the power outlet).

RGB / RGBW / MONO

supply voltage

energy consumption

number of outputs

type of outputs

maximum voltage

maximum load

color mode

dimensions

maximum current 12A (3A /channel)

for more information

visit our website

www.blebox.eu

or send us an email to: info@blebox.eu

support is available at

support@blebox.eu

ADDITIONAL INFORMATION

SOFTWARE UPDATE

To update the software in the controller, connect it to your home WiFi network

(see "Access Point and WiFi Network Settings" section) which is connected to

the Internet. Go to “Settings” (icon at the top-right corner of the screen) and

click the "Get new rmware" button in the nal section on settings. Wait about

1 minute, do not close the interface and don’t perform other actions. The

device will download the latest software. The software version number,

hardware version and device identier can be read at the bottom of the

settings screen.

made of polyurethane composition

not containing halogens, self-

extinguishing for thermal

class B (130 °C)

direct connection (as Access Point), Wi-Fi

connection via a standard router,

connection with access from any

location in the world (requires only

access to the Internet)

μWiFi, compatible with WiFi, 802.11g

bidirectional, encrypted

communication standard

transmission type

mode

radio frequency

API

compatible devices

IP20

2.4 GHz

open

Apple iPhone, Apple iPad, iPad Mini,

Android, computers and mobile

devices supporting HTML5

in the ush-mounted box, on the lamp

housing, directly connected

to the LED strip, e.g. furniture

inverted polarization, ESD

housing

protection level

mounting method

protection

LOCATION AND TIME OF THE DEVICE,

SCHEDULE

The controller has the ability to work according to a given schedule. To make

this possible, set the device's time. Go to settings in the "Device time" section,

click "Change timezone". Then select your region and location from the list,

conrm your selection clicking the "Save" button. The device will synchronize

its time with the server time (if the controller is in a WiFi network with access

to Internet) or it will download time from the phone / tablet. It is recommen-

ded that the controller is always connected to a WiFi network with Internet

access so that it can automatically synchronize its clock.

To be able to control devices using the local sunrise and sunset, you must also

select the location of the controller. You can specify the location of the device

using a smartphone or tablet. In the section "Device location", click "Set

locations". Browser will ask whether to share locations - allow. In the "Coordi-

nates" eld,should appear the approximate coordinates of your location. If the

"Set locations" button blinks red with the word "Error", or the "Coordinates"

eld did not change the value from "Not set" to numeric data, a failurehas

occurred during the location download. You should make sure that the phone

/ tablet has a GPS module and that the sharinglocation service is enabled on

the phone.

Adding schedule entries can be performed by clicking the "Add item" button

in the "Schedule" section of settings. You can select the days in which the task

will be performed, the type of entry (at a specic time, or relative to sunrise /

sunset - only having a correctly set location) and set the parameters of the

task. The set tasks will be visible as a list, individual entries can be edited or

deleted.

Product specificaties

Merk:	Blebox
Categorie:	Smarth home
Model:	wlightbox
Kleur van het product:	Zwart
Breedte:	39 mm
Diepte:	35 mm
Hoogte:	20 mm
Materiaal behuizing:	Polyurethaan
Stroombron:	DC
Internationale veiligheidscode (IP):	IP20
Connectiviteitstechnologie:	Draadloos
Aantal per verpakking:	1 stuk(s)
Frequentie:	2400 MHz
Op afstand bedienbaar:	Ja
Compatibele producten:	Apple iPhone, Apple iPad, iPad Mini
Spanning:	12 - 24 V