Blaupunkt SR-S1 Handleiding

Blaupunkt Alarmsysteem SR-S1

Lees hieronder de 📖 handleiding in het Nederlandse voor Blaupunkt SR-S1 (2 pagina's) in de categorie Alarmsysteem. Deze handleiding was nuttig voor 46 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Wireless Indoor Siren (SR S1)-

1. Mounting Holes x 4

2. Tamper Switch

The tamper switch protects the from being opened.cover

3. Function Switch Block

Contains 7 to enable the learning mode and to set DIP Switches

the alarm period of siren.

1 x Indoor Siren

4 x large wall plugs and screws

4 V x 1.5 D alkaline batteries

1. Open the front cover

2. Open the battery cover to insert batteries.compartment

3. ocate the L Function Switch Block. Use a sharp bject to o set

Dip SW3 & SW4 on the function switch block to your desired

alarm length.

4. ontrol anel Enter learning mode for your c p .

5. Slide the position Dip SW1 to ON . SR S1- will enter learning

mode. he code After 3 seconds, t Siren will send a learning

and emit a beep to confirm.

6. If the Control Panel receives the learning signal, please refer

to the Control Panel manual to complete the learning process.

When learning is complete, the Control Panel will send signal

to the The Siren to confirm. Siren will sound a short beep

again to indicate learning is successful.

If the Control Panel fails to receive a learning code, slide Dip

SW1 back to OFF, and then ON position again to enter

learning mode again.

7. does no I f the Siren t respond, please remove the Siren from

the control panel and repeat steps 4-6 again.

8. S lide Dip the SW1 to OFF position to leave learning mode. If

you do t slide Dip SW1 back to OFF position, the no Siren will

automatically leave the learning mode in one hour.

The Indoor Siren has 4 mounting holes on the back cover for wall

mounting.

Before Installation, refer to your Control Panel manual to

temporarily disable the Siren Tamper function to avoid

accidental alarm trigger.

1. Use the 4 mounting holes on the back to mark position on the

wall.

2. Drill holes into the wall using the mounting holes as template,

insert wall plugs if required,

3. Fix the base onto the wall with the screw and plugs provided.

4. Replace the front cover onto the base.

5. Enab le the Siren Tamper function on you Control Panel.

SW1

Siren Learning

OFF

Normal operation

Learn-in mode

SW2

Reserved

SW3

SW4

Siren Duration

OFF

3 min.

OFF

5 min.

OFF

10 min.

1 second (test)

SW5

Reserved

SW6

Memory Reset

OFF

Normal

Clear Memory

SW7

Supervision

OFF

Supervision function disable

Supervision function enable

 For further detail please see

aanndd

Mounting Holes

x 4

TTaammppeerr SSwwiittcchh

The Siren is protected by a tamper switch which will be activated

if the Siren is cover opened. When installing the Siren, please

make sure the tamper switch is properly compressed against the

front cover.

Before installing the Siren, changing mounting location or

batteries, please make sure to disable the tamper switch

temporarily using your Control Panel’s Siren Tamper function and

enable the tamper switch again after finish working on the Siren.

Please refer to your Control Panel manual for detail.

SSiirreenn AAuuddiibbllee PPeerrffoorrmmaannccee

The Siren produces a minimum of 104 dBA sound pressure at 1

meter range when activated.

For Burglar and Panic Alarm, the Siren gives a continuous alarm

sound.

For Fire / Water alarm, the Siren gives an intermittent alarm

sound of 2 sec siren followed by a 1 sec interval. -

The Siren is silenced when either the programmed siren length

expires or when the turn off the Control anel P is disarmed to Siren.

Please refer to Dip Switch table above to set your desired alarm

length through Dip Switch SW3 and SW4 setting.

Audio Status Indication Table

The Siren will sound indication beeps according to different status,

please refer to table below.

SSiirreenn AAuuddiioo

Arm/Home 1 beep*

Disarm 2 beeps*

Arm (Low Battery) 5 beeps

Disarm (Low

Battery) 5 beeps

Arm (Tamper) 5 beeps

Disarm (Tamper) 2 beeps*

Previous alarm

warning 3- second beep

Entry/Exit Sound Count-down beeps

* Siren Audio indication will be effected by the Confirmation

O N / OFF setting in your Control Panel settings.

The Siren uses four alkaline batteries 1.5V D as its power source.

It also features low battery detection function to notify the Control

Panel when battery voltage is low.

When the Siren is on low battery, follow the procedure below to

change the batteries.

1. Temporarily amper protection function disable the Siren’s t

(please refer to your manual Control Panel for detail). The

Siren will sound a beep to indicate the tamper is disabled.

2. Remove the front cover.

3. and Remove the four screws fixing the battery compartment

take off the compartment lid.

4. old Remove the batteries and press the Tamper Switch twice

to discharge.

5. new Insert the D cell alkaline batteries into the battery

compartment polarity according to correct .

6. The Siren will emit beeps when the last battery is inserted.

7. Replace the battery compartment lid and front cover

8. amper protection on Enable the t functi through your Control

Panel. The Siren will sound a beep to indicate.

- -10°C to 40°C, relative humidity 85% non condensing.

868 MHz

SSppeecciiffiiccaattiioonn

Product specificaties

Merk:	Blaupunkt
Categorie:	Alarmsysteem
Model:	SR-S1
Kleur van het product:	Wit
Soort:	Draadloze sirene
LED-indicatoren:	Status
Accu/Batterij voltage:	1.5 V
Levensduur batterij/accu:	2.5 jaar
Ondersteund aantal accu's/batterijen:	4
Geluidsdrukniveau:	104 dB
Frequentie:	868 MHz
Afmetingen (B x D x H):	113 x 54 x 228 mm
Bedrijfstemperatuur (T-T):	-10 - 45 °C
Batterijtechnologie:	Alkaline
Type batterij:	AAA
Aantal alarmgeluiden:	3