Best PM6 Handleiding

Best Niet gecategoriseerd PM6

Lees hieronder de 📖 handleiding in het Nederlandse voor Best PM6 (12 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 16 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

Page 1

Model PF6

FLEX BLOWER

WARNING

READ AND SAVE THESE INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR IN-

JURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer.

If you have questions, contact the manufacturer at the address

or telephone number in the warranty.

2. Before servicing or cleaning unit, switch power off at service

panel and lock the service disconnecting means to prevent

power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a

qualified person(s) in accordance with all applicable codes

and standards, including fire-rated construction codes and

standards.

4. Sufficient air is needed for proper combustion and exhausting

of gases through the flue (chimney) of fuel burning equip-

ment to prevent backdrafting. Follow the heating equipment

manufacturer’s guideline and safety standards such as those

published by the National Fire Protection Association (NFPA),

and the American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), and the local code au-

thorities.

5. When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. To reduce the risk of fire, use only metal ductwork.

8. This unit must be grounded.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

a) Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may

ignite. Heat oils slowly on low or medium settings.

b) Always turn hood ON when cooking at high heat or when

cooking flaming foods.

c) Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or filter.

d) Use proper pan size. Always use cookware appropriate

for the size of the surface element.

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE

EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE

FOLLOWINGa:

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or

metal tray, then turn off the burner. BE CAREFUL TO

PREVENT BURNS. If the flames do not go out immedi-

ately, EVACUATE AND CALL THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN - You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels - a

violent steam explosion will result.

4. Use an extinguisher ONLY if:

A. You know you have a Class ABC extinguisher, and you

already know how to operate it.

B. The fire is small and contained in the area where it

started.

C. The fire department is being called.

You can fight the fire with your back to an exit.D.

Based on “Kitchen Firesafety Tips” published by NFPA.

CAUTION

1. For indoor use only.

2. For general ventilating use only. Do not use to exhaust haz-

ardous or explosive materials and vapors.

3. To avoid motor bearing damage and noisy and/or unbalanced

impellers, keep drywall spray, construction dust, etc. off power

unit.

4. Clean filters and grease-laden surfaces frequently.

5. Do not repair or replace any part of this appliance unless

specifically recommended in this manual. All other servicing

should be done by a qualified technician.

6. Please read specification label on product for further information

and requirements.

7. To reduce the risk of fire and electric shock, install this blower

only with downdraft ventilator models shown below. Other

downdraft ventilator models cannot be substituted. (Downdraft

ventilators sold separately).

BEST

Models

D49M30SB, D49M36SB, D49M48SB

For use with these Downdraft Ventilators:

BEST® Models D49M30SB, D49M36SB,

D49M48SB

(Purchase Downdraft Ventilator separately.)

INSTALLER: Save this manual for Electrical Inspector and Homeowner to use.

Page 2

Model PF6

PLAN THE INSTALLATION

If you choose to mount the Flex Blower directly to the Downdraft

housing: Remove the inlet cover (taped in place for shipping)

and discard inlet cover. Refer to installation instructions in the

Downdraft manual.

If you choose to mount the Flex Blower in a remote location,

(such as the cabinet back, cabinet side, or floor joists) - follow

the instructions below.

INSTALL FLEX BLOWER

IN REMOTE LOCATION

NOTE: THE FLEX BLOWER MUST BE INSTALLED WITHIN

4-FEET OF THE DOWNDRAFT’S ELECTRICAL PANEL.

The Electrical Panel can be mounted directly to the Downdraft

housing - or mounted in a remote location (always within 4-feet

of the Flex Blower).

1. Position inlet cover over blower wheel. Securely attach the

inlet cover to the blower with 8 screws and 8 nuts from parts

bag. Note that inlet cover is taped to blower for shipping. This

tape may be removed.

2. Determine how the 8” round and ductwork INLET OUTLET

will connect to the Flex Blower.

3. Remove the necessary 1/4-20 x .50 hex head screws and attach

4 MOUNTING BRACKETS to the Flex Blower - using 4 of the

6 POSSIBLE BRACKET MOUNTING LOCATIONS.

4. Mount Flex Blower to back of cabinet, floor joist, or adequate

framework (constructed by installer) with appropriate

MOUNTING SCREWS (not included).

5. Connect 8” ROUND DUCT from Downdraft housing to Flex

Blower inlet and from Flex Blower outlet to roof or wall cap.

For best performance: Choose the ducting option which allows

the shortest length of ductwork and a minimum number of

elbows and transitions. Check location of floor joists, wall

studs, electrical wiring or plumbing for possible interference.

6. Use strain relief bushing (provided) to attach Flex Blower wiring

to wiring box on Downdraft’s electrical panel and make wiring

connections. (See Downdraft manual for instructions.)

INLET

(from downdraft)

OUTLET

(to roof cap

or wall cap)

(6) MOUNTING

BRACKET

LOCATIONS

8-IN.

ROUND

DUCT

(to roof cap

or wall cap)

8-IN.

ROUND

DUCT

(from

downdraft)

MOUNTING SCREWS

(not included)

(4) MOUNTING

BRACKETS

attached with

1/4-20 X .50

HEX HEAD

SCREWS

CONTENTS

These parts are included with your Flex Blower:

2 - blower mounting legs*

1 - Parts Bag containing:

(4) wood screws #10 x .50*

(4) blower mount brackets

(1) strain relief bushing

(8) screws #10 x .38

(8) nuts #10

* For use when mounting Flex Blower directly to Downdraft

housing. (See Downdraft instruction manual.)

BLOWER

INLET

COVER

Page 3

Model PF6

SERVICE PARTS

KEY DESCRIPTION QTYPART

NUMBERNO.

1 97020267 Inlet Cover - including: 1

8 screws, #10 x 3/8

8 nuts, #10

2 97017924 Blower (complete) 1

(includes key nos. 7-11 & Hardware Bag)

+ 97018828 Hardware Bag - containing: 1

1 retaining ring

4 grommets

4 screws, M4 x 16.8mm

3 screws, M4 x 0.7 x 16mm

1 screw, M4 x 0.7 x 12mm

3 97020266 Blowerbox End - Blower Mount 1

(includes strain relief)

4 99271511 1Wire Harness

(includes strain relief)

5 98011179 2Blower Mounting Legs

6 97020268 Parts Bag - containing: 1

4 blower mounting brackets

4 wood screws, #10 x .50

1 strain relief bushing

8 screws, #10 x .38

8 nuts, #10

10 screws, 1/4 x .50

7 99111448 Blower Housing, Motor 1

8 99111447 1Blower Housing, Inlet

9 99271379 Capacitor 1

110 99020298 Blower Wheel

111 99080629 Motor

+ Not Shown

Product specificaties

Merk:	Best
Categorie:	Niet gecategoriseerd
Model:	PM6

Heb je hulp nodig?

Als je hulp nodig hebt met Best PM6 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Best

Best MD8T Handleiding

2 Oktober 2024

Best MD8TU Handleiding

2 Oktober 2024

Best ACRDBLS Handleiding

2 Oktober 2024

Best HARKBN30 Handleiding

2 Oktober 2024

Best HARKBN24 Handleiding

2 Oktober 2024

Best 639 Handleiding

2 Oktober 2024

Best PM6 Handleiding

2 Oktober 2024

Best HAWTBN36 Handleiding

2 Oktober 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Axler Hammerhead Pro Follow Focus Handleiding

19 December 2024

Axler Hammerhead Follow Focus Handleiding

19 December 2024

Cosatto Giggle 4 Handleiding

19 December 2024

Yamazen LCR-80-FSET Handleiding

19 December 2024

Asus EBS-P300 Handleiding

18 December 2024

QSC AcousticDesign AD-C245C Handleiding

18 December 2024

Asus ZenWiFi ET9 Handleiding

18 December 2024

Asus NUC 12 Extreme Compute Element Handleiding

18 December 2024

Asus NUC 11 Extreme Kit Handleiding

18 December 2024

Asus NUC 12 Pro X Kit Handleiding

18 December 2024