BeSafe iZi Flex FIX i-Size Handleiding

BeSafe Autostoel iZi Flex FIX i-Size

Lees hieronder de šŸ“– handleiding in het Nederlandse voor BeSafe iZi Flex FIX i-Size (101 pagina's) in de categorie Autostoel. Deze handleiding was nuttig voor 55 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/101
a
c
b
d
i
l
j
k
g
e
f
h
m
5 6
7
8
9
4
2
3
1
n
USER MANUAL
Stature height 100-150 cm
Age 4-12 y UN regulation no. R129
110
116
122
128
134
140
146
152
158
164
170
176
182
193
199
205
8
14
20
26
32
38
44
50
56
62
68
74
80
86
92
98
104
8 9
! Vital information
ā€¢ For the correct usage of the airbag in combination with the seat;
read the vehicle handbook.
ā€¢ For the suitable positions in the car, read the vehicle handbook.
ā€¢ BeSafe recommends to install the seat in all vehicle seat positions
which are intended to be used and check installation, available
space in the vehcile and position of the child, to verify if the seat is
acceptable for your situation.
ā€¢ iZi Flex FIX i-Size can be installed forward-facing with the ISOFIX
anchorage in a vehicle equipped with ISOFIX anchorage points, in
combination with a 3-point belt, approved to UN/ECE Regulation
No.16 or other. When there is no ISOFIX anchorage available in the
vehicle position, iZi Flex FIX i-Size can be installed forward-facing
with a 3-point belt, approved to UN/ECE Regulation No.16 or other.
ā€¢ iZi Flex FIX i-Size is approved for stature height 100 cm - 150 cm,
in the forward-facing direction.
ā€¢ When used for stature heights between 135 cm. and 150 cm iZi
Flex FIX i-Size might not ļ¬t in all vehicles, due to a low position of
the vehicle roof at the side.
ā€¢ Before every use, make sure that the 3-point belt is not damaged
or twisted and installed tight.
ā€¢ When used without the isoļ¬x anchorages connected, the
seat should always be restrained by the vehicle belt when it is
transported without the child.
ā€¢ When the child is taller then 150 cm. or the shoulders exceed the
highest position of the shoulderbelt guiders, the child must change
to a seat suitable for longer children, normally the vehcile seat.
ā€¢ After an accident, the seat must be replaced. Although it may
look undamaged, if you were to have another accident, the seat
may not be able to protect your child to the level to which it was
designed.
ā€¢ Prevent the seat from becoming trapped or weighed down by
luggage, seats and/or slamming doors.
ā€¢ DO NOT attempt to dismantle a part, which is not intented to be
removed, modify or add any part to the seat. Warranty will be void
26
28 29 30
27
13
10 11 24 25
15
21 22 23
19 20
14
12
17
16 18
Thank you for choosing BeSafe iZi Flex FIX i-Size
! It is important that you read this user manual BEFORE
installing your seat. Incorrect installation could endanger
your child.
10 11
ā€¢ Adjustable headrest
ā€¢ Shoulderbelt lock
ā€¢ Shoulderbelt guide
ā€¢ Lapbelt guider
ā€¢ Reclining handles (2x)
ā€¢ Base
ā€¢ ISOļ¬x release handle
ā€¢ SIP bumper
ā€¢ Height adjustment handles (2x)
ā€¢ ISOļ¬x connectors (2x)
ā€¢ ISOļ¬x release buttons (2x)
ā€¢ ISOļ¬x indicators (2x)
ā€¢ ISOļ¬x vehicle anchorage (2x)
ā€¢ PAD+
(1a)
(1b)
(1c)
(1d)
(1e)
(1f)
(1g)
(1h)
(1i)
(1j)
(1k)
(1l)
(1m)
(1n)
Preparing to install
Installation
1. When installing the seat in the front vehicle seat make sure the
backrest of the vehicle seat is in an upright position.
2. Position the seat inside the vehicle.
3. Pull the ISOļ¬x release handle to release the ISOļ¬x connectors. A
button on top of the handle will keep the handle in the released
position and locks the ISOļ¬x connectors to slide in the base again.
(2) The ISOļ¬x arms lock only in the position where it is totally
extended. In this locked position 2 red marks next to the button on
the handle will become visible. (3)
4. Click the ISOļ¬x connectors to the ISOļ¬x anchorage points in the
vehicle seat (4). Make sure that all ISOļ¬x indicators are GREEN. (5, 6)
5. Press the button on top of the ISOļ¬x release handle (located
between the red marks) down and push the handle back into the
base. (7, 8) Push the seat as far as possible towards the backrest of
the vehicle seat. (9)
6. Make sure the back of the seat is touching the backrest of the vehicle
seat. If the headrest of the vehicle is pushing the seat away from the
backrest, adjust the headrest.
7. If the seat cannot be used in combination with ISOļ¬x anchorage
points in the vehicle seat, the ISOļ¬x connectors can be stowed inside
the seat and the seat can be used in combination with the 3-point
belt only.
8. Slide the shoulderbelt in the shoulderbelt guide. (10) Make sure the
belt is not twisted and that the shoulderbelt guide is closed again to
keep the belt inside. (11)
9. The seat is delivered with removable SIP+ (side impact protection
+). This extra side impact protection should be used on the door
side of the vehicle. It can be connected on the outside of the side
bumper in 2 slots. The seat already oī˜žers high level integrated side
impact protection. This extra side impact protection improves the
protection in a side impact still further. (12)
10. Do not use the SIP+ on the seat when the space between seat and
door of the vehicle is too small, which might lead to a situation
where the seat is not positioned correctly on the vehicle seat.
1. Adjust the headrest to the correct height by turning the height
adjuster handle. (13) Make sure that the shoulder belt is level with
your childā€™s shoulder. (14)
2. The seat can be positioned in 2 positions by pulling the reclining
handle upwards and pushing the seat forwards or backwards. Position
the seat in the correct position before positioning the child with the
vehicle belt. (15)
3. Position the vehicle belt in front of the child and lock the belt into the
buckle of the vehicle. (16, 17)
4. BeSafe recommends to use the lapbelt guider to keep the child
seated in the optimum upright position. To use the lapbelt guider
position the lapbelt through the lapbelt guider.
5. The PAD+ must be used around the shoulder vehicle belt and
positioned between the chin and the chest of the child.
6. Remove slack in the belt by pulling the belt towards the retractor. (18)
Positioning of the child
Removing the seat
1. Remove the shoulderbelt out of the shoulderbelt guide by pushing
the shoulderbelt lock in the guider up and slide the belt out. (19, 20)
2. Pull the ISOļ¬x release handle to release the ISOļ¬x connectors. (21)
In this way the base of the seat can move forwards and the ISOļ¬x
release buttons can be operated. (22)
3. Release both ISOļ¬x connectors, by pushing down the release
buttons. (23) Slide the arms with ISOļ¬x connectors inside the seat
before you remove the seat from the vehicle. To be able to slide
the arms with ISOļ¬x connectors inside the seat, press the button
(between the red marks) on top of the ISOļ¬x release handle down.
4. Remove the seat from the vehicle.


Product specificaties

Merk: BeSafe
Categorie: Autostoel
Model: iZi Flex FIX i-Size

Heb je hulp nodig?

Als je hulp nodig hebt met BeSafe iZi Flex FIX i-Size stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Autostoel BeSafe

Handleiding Autostoel

Nieuwste handleidingen voor Autostoel