Berker 85341185 Handleiding

Berker Bewegingsmelders 85341185

Lees hieronder de 📖 handleiding in het Nederlandse voor Berker 85341185 (10 pagina's) in de categorie Bewegingsmelders. Deze handleiding was nuttig voor 90 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/10

Page 1/10

6LE005154A 2017-11

Motion detector 1.1 m

Order no. 8534 11 xx

Motion detector 2.2 m

Order no. 8534 21 xx

Operating instructions

1. Safety instructions

Electrical equipment may only be installed and assembled by a qualied electrician in ac-

cordance with the relevant installation standards, regulations, directives and safety and

accident prevention directives of the country.

Failure to comply with these installation instructions may result in damage to the device,

re or other hazards.

Due to its detection behaviour the device is not suitable for use in burglary detection or

alarm systems.

These instructions are an integral component of the product and must be retained by the

end user.

2. Design and layout of the device

(3)

(4)

(5)

(2)

(1)

(6)

Figure 1: Design and layout of the device

(1) Insert (see "Accessories", not in scope of delivery)

(2) Frame (not within scope of delivery)

(3) Application module

(4) Motion detector design cover

(5) Screw for dismantling protection (not for design lines R.1/R.3)

(6) Interface between insert/application module

Page 2/10

6LE005154A 2017-11

3. Function

Correct use

–Automatic switching of lighting depending on heat motion and ambient brightness

–Application module for switch insert, ush-mounted dimmer or motion detector extension

unit

–

Only suitable for use in indoor areas with no drip and no spray water.

Product characteristics

–Integrated button for selecting operating modes and special functions

–Lockable integrated button

–Operating mode - automatic mode, permanent ON, permanent OFF can be selected

–Display operating mode via LED

–Potentiometer for adjusting the response brightness and detection sensitivity

–Adjustable detection angle for adaptation of the detection area

–

Additional adjustment of the response brightness via Teach-In function

–Party function

–Presence simulation

–Operation on motion detector extension units

–Optional extension unit operation via installation button

Automatic mode

The motion detector detects heat motion caused by people, animals, or objects.

Applied on switch insert:

–The light will be switched on for a (xed) delay time of 3 minutes if movements are

detected in the detection area and the set brightness threshold is undershot. Each detected

movement restarts the delay time.

–The light will be switched off after 3 minutes if no additional movements are detected.

On ush-mounted dimmer:

–The light will be switched on to the switch-on brightness level for a (xed) delay time of 3

minutes if movements are detected in the detection area and the set brightness threshold is

undershot. Each additional movement in the detection area restarts the delay time.

–After the delay time elapses the lighting will be dimmed to 50% of the switch-on brightness-

level and will remain at this brightness level for 30 s (switch-off pre-warning). Each

movement detected during the switch-off pre-warning restarts the delay time and restores

the switch-on brightness level.

–The light will be switched off if no motion is detected any longer in the detection area and

the set delay time and the switch-off time have elapsed.

On extension unit

–If motion is detected in the detection area of the extension unit, the extension unit insert

sends a pulse to the main unit and then locks for 10 seconds. Recording takes place in-

dependently of the brightness on the extension unit. If motion is still detected after 10 se-

conds, a pulse is sent again.

–Upon receiving an extension unit pulse, the main unit switches the light on for the delay

time, if the set brightness threshold is undershot. Every further extension unit pulse restarts

the delay time of the main unit.

Page 3/10

6LE005154A 2017-11

Performance after mains breakdown/return of mains supply

–Mains breakdown shorter than 0.2 s:

The function is not impaired.

–Mains breakdown longer than 0.2 s:

There is no function during the mains breakdown. The current conguration is saved in

non-volatile memory.

–Return of mains supply:

The application module executes an initialisation for approx. 15 s, during which the lighting

will be switched on. Motion detection starts thereafter. If no motion is detected during the

rst 5 s, the lighting is switched off. The saved conguration is loaded from memory. During

this period local operation via the button or extension unit can be used.

4. Operation

Operating concept

(8)

(7)

Fig. 2: Operating and display elements

(7) Button

(8) Status LED

Operation is executed by pushing the button (7) on the motion detector:

–

A short press of the button switches the operating modes. The operating mode is displayed

via the status LED behind the optics cover of the motion detector.

–Keeping the button pressed activates special functions. Selection of the special functions is

supported by the LED display (Fig. 3).

Function Party function Teach-In Keylock Presence

simulation

Load setting

mode1)

LED display

Hold time

operation

button

> 5 s > 10 s > 15 s > 20 s > 25 s

1) Only on universal switch insert and universal ush-mounted dimmer

Fig. 3: Selection of the special functions and LED display

Selecting the operating mode

Briey press the button repeatedly until the desired operating mode is selected.

The status LED indicates the selected operating mode (see Table 1).

Product specificaties

Merk:	Berker
Categorie:	Bewegingsmelders
Model:	85341185
Kleur van het product:	Antraciet
Materiaal behuizing:	Thermoplastic
Internationale veiligheidscode (IP):	IP20
Plaatsing:	Binnen
Connectiviteitstechnologie:	Bedraad
Montagewijze:	Muur
Vals-alarmbescherming:	Ja
Bedrijfstemperatuur (T-T):	-5 - 45 °C
Detectie hoek:	90 °
Detectieafstand:	12 m
Installatie hoogte (max):	1.1 m
Lichtgevoeligheid:	1000 Lux