BeamZ S1800 160.493 Handleiding

BeamZ Mes S1800 160.493

Lees hieronder de 📖 handleiding in het Nederlandse voor BeamZ S1800 160.493 (12 pagina's) in de categorie Mes. Deze handleiding was nuttig voor 50 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

Ref. Nr. 160.493

S1800 DMX

INSTRUCTION MANUAL

GEBRUIKSAANWIJZING

BEDIENUNGSANLEITUNG

- 2 -

Warning:

- The smokemachine must be placed at least 100 cm away from inﬂammable materials such as curtains, books,

etc. Make sure that the housing cannot be touched by accident.

- For indoor use only.

- During installation, nobody should stand beneath the mounting area.

- Prior to the ﬁrst use, have the unit checked by a qualiﬁed person.

- The unit contains voltage carrying parts. DO NOT open the smokemachine

- Never plug or unplug the unit with wet hands.

- If the plug and/or mains lead are damaged, they need to be repaired by a qualiﬁed technician.

- If the unit is damaged to an extent that you can see internal parts, do not plug the unit into a mains outlet. It

needs to be repaired by a qualiﬁed technician.

- Only connect this unit to an earthed mains outlet of 230Vac/50Hz .

- Always unplug the unit during a thunderstorm or when it is not in use.

- If the unit has not been used for a longer period of time, condensation can occur inside the housing. Please let

the unit reach room temperature prior to use.

- When you unplug the unit from the mains always pull the plug, never the lead.

- In order to avoid accidents in public premises, the local legal requirements and safety regulations/warnings must

be fulﬁlled.

- Keep out of the reach of children.

Safety

Plug the smoke machine only in an earthed mains outlet or extension cord! ATTENTION: the powercord can only be

replaced by an original replacement, supplied by Tronios. Be careful when ﬁlling the ﬂuid tank. First of all, unplug the

mains lead! Then unscrew the cap on the tank and ﬁll it by means of a funnel. Only use the original Beamz smoke ﬂuid

which is environmental friendly and, if used correctly, leaves no residues. Do not obstruct the openings on top of the case

to guarantee a good ventilation. The heating element of the smoke machine generates heat which needs to be removed.

Don’t put any objects on the smoke machine.

Installation and Use

Unpack the fog machine. Do not connect yet the net cable. Connect the lead of the manual control with the 3-pin plug at

the rear of the smoke machine. Fill the ﬂuid tank by means of a funnel. Plug the unit into a mains outlet. Thus the heating

element is automatically switched on. Depending on the room temperature, it takes about 6 minutes until the working

temperature is reached. Then the thermostat is clicking and the LED on the manual control lights up. Push the switch once

and the smoke machine will produce a nice thick fog. Once the smoke machine has reached its working temperature (the

LED is lit) the smoke machine can produce continuously fog during max 1 minute. After this period of time, the fog

generator is cooled so much down that the thermostat switches oﬀ. Wait a few minutes until the working temperature is

reached again. It is recommended to produce smoke with small pauses in between so that the temperature is maintained

and the thermostat doesn’t switch oﬀ.

- 3 -

Location

Select a location where it is easy to ﬁll the tank. It is also possible to hang the unit by means of the supplied holder and

ﬁxing screws.

Switching the unit oﬀ

Switch the unit oﬀ by unplugging it from the mains. Otherwise the 1800W heating element will draw unnecessarily current.

Settings

Press the MENU button on the remote control to select the various functions . Press the UP and DOWN buttons to

set the various functions . After 10 seconds, the settings are automatically transferred and the unit is ready for use.

- Man Vol Out: amount of smoke in % , when using the LOCK button on the remote

- Set Interval : the time between the outputs in seconds , using the TIMER function on the remote

- Set Duration : the length of the outputs in seconds , using the TIMER function on the remote

- Volume Out: no function with this machine

- DMX512 # 000-512 : Start Address when using a DMX controller

DMX operation

Connect the machine directly to a DMX controller or DMX DMX loop with multiple effects. The machine uses a

3-pin XLR connector for DMX connection.

Address Setup: Press the MODE button several times until DMX512 # ... is displayed, use the UP / DOWN buttons

to set the start address. The start address is deﬁned as a ﬁrst channel to which the machine will respond. Verify that

there are no overlapping channels used!

Note: It is necessary to always ﬁnish with a 120 Ohm termination plug for proper data transmission DMX loop..

Maintenance

Reﬁlling the ﬂuid reservoir should be done carefully. Remove the plug from the mains ﬁrst! Then unscrew the cap of the

reservoir and ﬁll it by means of a suitable funnel. Use only the original Beamz smoke liquid. This ﬂuid is environmentally

friendly, biodegradable and leaves no residue when used correctly. Make sure the smoke liquid to become contaminated,

close the cap of the liquid smoke can and after ﬁlling tank right.

After 40 hours, the smoke machine must be cleaned to avoid deposits in the machine, pump and heater.

Clean procedure: Run clean procedure in a well-ventilated area

• Remove smoke liquid from the tank, add cleaning solution to tank

• Switch smoke machine and wait until it is warm up

• Press the button to switch the liquid pumped through the machine

• Perform the above operation until the tank is empty

• Fill the tank with liquid smoke

CHANNEL

VALUE FUNCTION

0 – 100% Smoke level

Product specificaties

Merk:	BeamZ
Categorie:	Mes
Model:	S1800 160.493
Kleur van het product:	Grijs
Gewicht:	7300 g
Snoerlengte:	3 m
Vermogen:	1800 W
Afstandsbediening:	Bedraad
Op afstand bedienbaar:	Ja
Opwarmtijd:	6 min
Productafmetingen (B x H x D):	450 x 330 x 190 mm
AC-ingangsspanning:	220-240 V
AC-ingangsfrequentie:	50 Hz
Vloeistoftank capaciteit:	2.5 l
Hoeveelheid rook uitstoot:	350 m³/min
Bedrijfsvloeistof:	Water