BeamZ ICE1800 160.518 Handleiding

BeamZ Mes ICE1800 160.518

Lees hieronder de 📖 handleiding in het Nederlandse voor BeamZ ICE1800 160.518 (12 pagina's) in de categorie Mes. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

Ref. Nr. 160.518

ICE FOGGER

ICE 1800

INSTRUCTION MANUAL

GEBRUIKSAANWIJZING

BEDIENUNGSANLEITUNG

V1.1

- 2 -

Warning:

- The smokemachine must be placed at least 100 cm away from inﬂammable materials such as curtains,

books, etc. Make sure that the housing cannot be touched by accident.

- Use only Beamz water-based smoke ﬂuid recommended by your dealer.

- Poor smoke liquid caused permanent damage, bad eﬀect, clogging, spitting of unevaporated liquid etc.

- Never add ﬂammable ﬂuids (oil, gas, perfume) to the fog liquid.

- Always keep enough smoke liquid in the tank.

Use of the device without liquid will cause damage to the pump and heater.

- Do not obstruct the openings on top of the case to guarantee a good ventilation.

- Don’t put any objects on the smoke machine.

- For indoor use only.

- During installation, nobody should stand beneath the mounting area.

- Prior to the ﬁrst use, have the unit checked by a qualiﬁed person.

- The unit contains voltage carrying parts. DO NOT open the smokemachine

- Never plug or unplug the unit with wet hands.

- If the plug and/or mains lead are damaged, they need to be repaired by a qualiﬁed technician.

- If the unit is damaged to an extent that you can see internal parts, do not plug the unit into a mains outlet. It

needs to be repaired by a qualiﬁed technician.

- Only connect this unit to an earthed mains outlet of 220- Vac/50Hz . 240

- Always unplug the unit during a thunderstorm or when it is not in use.

- If the unit has not been used for a longer period of time, condensation can occur inside the housing. Please

let the unit reach room temperature prior to use.

- When you unplug the unit from the mains always pull the plug, never the lead.

- In order to prevent dropping of the unit, a safety fastening needs to be installed. This can be a solid chain, a

steel cable, etc. which has to be fastened separately from the mounting bracket.

- The supplied bracket is the main ﬁxing and must be used to solidly mount the light eﬀect.

- In order to avoid accidents in public premises, the local legal requirements and safety regulations/warnings

must be fulﬁlled.

- Keep out of the reach of children.

Location

Select a location where it is easy to ﬁll the tank. It is also possible to hang the unit by means of the supplied

holder and ﬁxing screws.

Installation and Use

Unpack the fog machine. Do not connect yet the net cable. Connect the remote control to the connector on the

back of the fogger. Fill the ﬂuid tank by means of a funnel. Fill the ice tray with ordinary ice. Close the drain

valve oﬀ. (Once ice has melted, you can drain the water here.) When the machine is ﬁlled with ice, the lid can

be closed.

Attention:Drain the water, melted ice regularly. (approximately every 45 minutes)

Plug the unit into a mains outlet. Thus the heating element is automatically switched on. Depending on the room

temperature, it takes about 8 minutes until the working temperature is reached. Then the thermostat is clicking

and the LED on the manual control lights up. Push the switch once and the smoke machine will produce a nice

thick fog. Once the smoke machine has reached its working temperature (the LED is lit) the smoke machine can

produce fog for a while. After this period of time, the fog generator is cooled so much down that the thermostat

switches oﬀ. Wait a while until the working temperature is reached again. It is recommended to produce smoke

with small pauses in between so that the temperature is maintained and th e thermostat doesn’t switch off.

Make sure that there is always enough liquid smoke contained in the tank. Use of the smoke machine without

liquid can permanently damage the unit. Once the smoke machine generates little smoke or pump generate

another 'rattling' sound i turn oﬀ the unit direct. Check the ﬂuid level and ﬁll the tank when it is empty, check the

hose and ﬁlter blockages and restore it. Plug in the unit and check if the problem is resolved. If problem persists,

switch unit direct off to prevent further damage and contact your dealer.

Switching the unit oﬀ

Switch the unit oﬀ by unplugging it from the mains. Otherwise the 1800W heating element will draw

unnecessarily current.

- 3 -

Timer remote control

Connect the remote control to the connector on the back of the fogger.

After some warm-up time, the device is ready for use, the LED will light up on the remote. During use, it may

happen that the machine stops, in this case the LED will go out, indicating that the machine is warming up.

Timer function:

Press the yellow button and set the interval, duration and volume controls to the desired level.

Interval: time between the smoke moments (10-200 seconds)

Volume: amount of smoke (0-100%)

Duration: duration of the smoking time

Continuous function:

Press the red button and set the volume to the desired level. The machine will continueously produce an

amount of smoke. It may be that the machine in between have to warm up, during this period no smoke is

produced. How many times this is done depends on the amount of smoke.

Manual Mode:

Press the green button to produce 100% smoke immediately; this button overrides all previous settings.

DMX control

Connect the device directly to a DMX controller or a DMX loop with multiple DMX effects. The machine has a 3-

pin XLR connector for DMX connection.

The machine needs 1 DMX channel to function:

Address Setup:

Use the DIP switch on the rear panel to set the start address. The base/start address is deﬁned as a ﬁrst

channel, where responsive to the device. Check if no overlapping channels are used!

Switch dip 10 on to activate the addressing

Set the desired address with the remaining 9 dips

Example addressing:

Startadres

Dipswitch setting

0000000001

0010000001

0000010001

1010000001

0001100001

0100001001

1110000001

105

0001011001

Note:

It is necessary always lock a DMX loop with a 120 Ohm terminator for correct data

transmission.

CHANNEL

VALUE

FUNCTION

0 – 100%

Smoke level

Product specificaties

Merk:	BeamZ
Categorie:	Mes
Model:	ICE1800 160.518
Kleur van het product:	Black, White
Gewicht:	16900 g
Snoerlengte:	3 m
Vermogen:	1800 W
Afstandsbediening:	Bedraad
Op afstand bedienbaar:	Ja
Opwarmtijd:	8 min
Productafmetingen (B x H x D):	750 x 405 x 395 mm
AC-ingangsspanning:	220-240 V
AC-ingangsfrequentie:	50 Hz
Vloeistoftank capaciteit:	2.5 l
Hoeveelheid rook uitstoot:	200 m³/min
Bedrijfsvloeistof:	Water