Be Quiet! Shadow Rock 2 Handleiding

Be Quiet! Hardwarekoeling Shadow Rock 2

Lees hieronder de 📖 handleiding in het Nederlandse voor Be Quiet! Shadow Rock 2 (2 pagina's) in de categorie Hardwarekoeling. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Installing of the mounting brackets

Attach the two Intel mounting brackets (4) to the underside of

the CPU cooler using the M3x3 screws (11).

Mounting the CPU cooler

First remove the protective foil from the underside of the

cooler. Spread the thermal paste (15) on the surface of the

CPU. The amount supplied is sufﬁ cient for one or two

applications.

Connect the fan to the CPU fan connector on the

motherboard.

Position the cooler so that it is possible to attach the cooler by

screwing together the M3x16 screws (9)

on the rear side of the motherboard into the hexagonal nuts

with sleeve (6) attached to the cooler.

Connect the fan to the CPU fan connector on the

motherboard.

Position the cooler over the CPU.

Place the hexagonal nuts (8) over the spacer nuts (7) and

progressively tighten these in a crosswise manner until ﬁ rm

using the hexagonal wrench (14).

Introduction: Thank you for deciding to purchase a be quiet!

product. The following instructions will guide you through the

installation process. If you do encounter installation problems,

please don't hesitate to contact our customer services by

mailing service@bequiet.com. Please note that be quiet!

cannot accept liability for damage caused by compatibility

problems.

Warranty:

• 3 years manufacturer guarantee for consumers (original

purchase from authorized be quiet! dealers only)

• Guarantee work can only be processed with an included

copy of the purchase receipt from an authorized be quiet!

dealer

• Manipulation and structural changes of any kind as well

as damages through external mechanical forces lead to a

complete voiding of the guarantee

• Our General Warranty Conditions apply, which can be

viewed on bequiet.com

Listan GmbH & Co.KG . Biedenkamp 3a . 21509 Glinde

Germany

For further information contact us via e-mail:

service@bequiet.com

SCOPE OF DELIVERY

General

We recommend mounting the cooler outside the PC case.

The following parts are needed for this:

1x be quiet! Shadow Rock 2 CPU cooler (1), 2x Intel mounting

brackets (4), 4x spacer nuts (7), 4x hexagonal nuts (8), 4x

M3x3 screws (11), 1x hexagonal open-end wrench (14), 1x

thermal paste (15)

First screw the spacer nuts (7) onto the threads of the LGA

2011(-3) square ILM socket frame. Use the hexagonal wrench

(14) for this.

Installation of the mounting brackets

Attach the two Intel mounting brackets (4) to the underside of

the CPU cooler using the M3x3 screws (11).

Mounting the CPU cooler

First remove the protective foil from the underside of the

cooler. Spread the thermal paste (15) on the surface of the

CPU. The amount supplied is sufﬁ cient for one or two

applications.

General

With preassembled motherboards we recommend installing

the cooler inside the PC case over the motherboard cutout.

The following parts are needed for this:

1x be quiet! Shadow Rock 2 CPU cooler (1), 1x Intel backplate

(2), 2x Intel mounting brackets (4), 4x hexagonal nuts with sleeve

(6), 4x hexagonal nuts (8), 4x M3x16 screws (9), 4x M3x3 screws

(11), 4x C-proﬁ le spacers (12), 1x hexagonal wrench (14), 1x

thermal paste (15)

Afﬁ xing the backplate

Position the Intel backplate (2) on the rear side of the

motherboard. Then insert the M3x16 screws (9) through the

drill holes situated on the rear side of the backplate.

Fasten the backplate on the front side of the motherboard

using the C-proﬁ le spacers (12) by pressing these onto the

notches in the M3x16 screws (9) until they click in.

Assembly of the mounting brackets

Insert the hexagonal nut with sleeve (6) from below through

each Intel mounting bracket (4) and screw together from

above with the hexagonal nuts (8). Use the hexagonal wrench

(14) for this.

1366

1150, 1151,

1155, 1156

775

(Bottom view)

775

1150, 1151,

1155, 1156

1366

Intel LGA 2011(-3) square ILM / LGA 2066 Intel LGA 775 / 1366 / 1150 / 1151 / 1155 / 1156

We recommend removal of the cooler prior to transportation.

July 2017

Part name Quantity

be quiet! Shadow Rock 2 cooler 1

Intel backplate 1

AMD backplate 1

Intel mounting brackets 2

Short AMD mounting brackets 2

Hexagonal nuts with sleeve 4

Spacer nuts 4

Part name Quantity

Hexagonal nuts 4

M3x16 screws 4

AMD M3x15 screws 4

M3x3 screws 4

C-proﬁ le spacers 4

AMD washers 4

Hexagonal wrench 1

Thermal paste 1

Preparing the mounting brackets

Pass the hexagonal nuts with sleeve (6) from below through

the ends of short AMD mounting brackets (5) and screw

together with the hexagonal nuts (8). Use the hexagonal

wrench (14) for this..

Assembly of the mounting brackets

Attach the two short AMD mounting brackets (5) to the underside

of the CPU cooler using the M3x3 screws (11).

Mounting the CPU cooler

First remove the protective foil from the underside of the

cooler. Spread the thermal paste (15) on the surface of the

CPU. The amount supplied is sufﬁcient for one or two

applications.

The fan can be mounted on all for sides for best heat

convection. Connect the fan to the CPU fan connector on the

motherboard.

Position the cooler above the CPU, passing the attached AMD

mounting brackets (5) over the projecting AMD M3x15 screws

(10) and afﬁx by turning the AMD M3x15 screws (10) from the

rear side of the motherboard.

General

With pre-mounted motherboards we recommend installing

the cooler inside the PC case over the motherboard cutout.

Removing the AMD retention module is performed at your

own risk.

The following parts are needed for this:

1x be quiet! Shadow Rock 2 CPU cooler (1), 1x AMD backplate

(3), 2x short AMD mounting brackets (5), 4x hexagonal nuts

with sleeve (6), 4x hexagonal nuts (8), 4x AMD M3x15 screws

(10), 4x M3x3 screws (11), 4x C-proﬁle spacers (12), 4x AMD

washers (13), 1x hexagonal wrench (14), 1x thermal paste (15)

Removal of the AMD retention module

Before you are able to install the CPU cooler, you must ﬁrst

remove the preassembled AMD retention module from the

motherboard. To do this remove the four screws from around

the socket

Mounting the backplate

Position the AMD backplate (3) vertically on the rear side of

the motherboard. Then insert the AMD M3x15 screws (10)

through the drill holes on the rear side of the backplate.

On the front side of the motherboard, pass the AMD washers

(13) over the projecting AMD M3x15 screws (10) to cover the

motherboard screw holes.

Now fasten the backplate on the front side of the motherboard

using the C-proﬁle spacers (12) by pressing these onto the

notches in the AMD M3x15 screws (10) until they click in.

AMD AM2(+) / AM3(+) / FM1 / FM2(+)

AM2(+)

AM3(+)

FM1/FM2(+)

(Bottom view)

Preparing the mounting brackets

Pass the hexagonal nuts with sleeve (6) from below through

the ends of short AMD mounting brackets (5) and screw

together with the hexagonal nuts (8). Use the hexagonal

wrench (14) for this..

Installing the mounting brackets

Attach the two short AMD mounting brackets (5) to the

underside of the CPU cooler using the M3x3 screws (11).

Mounting the CPU cooler

First remove the protective foil from the underside of the

cooler. Spread the thermal paste (15) on the surface of the

CPU.

The fan can be mounted on all for sides for best heat

convection. Connect the fan to the CPU fan connector on the

motherboard.

Position the cooler above the CPU, passing the attached AMD

mounting brackets (5) over the projecting AMD M3x15

screws (10)

and afﬁx by turning the AMD M3x15 screws (10) from the rear

side of the motherboard.

AM4

General

With preassembled motherboards we recommend installing

the cooler inside the PC case over the motherboard cutout.

Removing the AMD retention module is performed at your

own risk.

The following parts are needed for this:

1x be quiet! Shadow Rock 2 CPU cooler (1), 1x AMD backplate

(3), 2x short AMD mounting brackets (5), 4x hexagonal nuts

with sleeve (6), 4x hexagonal nuts (8), 4x AMD M3x15 screws

(10), 4x M3x3 screws (11), 4x C-proﬁle spacers (12), 4x AMD

washers (13), 1x hexagonal wrench (14), 1x thermal paste (15)

Removal of the AMD AM4 retention module

Before you are able to install the CPU cooler, you must ﬁrst

remove the preassembled AMD AM4 retention module from

the motherboard. To do this remove the four screws from

around the socket.

Mounting the backplate

Position the AMD backplate (3) vertically on the rear side of

the motherboard. Then insert the AMD M3x15 screws (10)

through the drill holes on the rear side of the backplate.

On the front side of the motherboard, pass the AMD washers

(13) over the projecting AMD M3x15 screws (10) to cover the

motherboard screw holes.

Now fasten the backplate using the C-proﬁle spacers (12) by

pressing these onto the notches in the AMD M3x15 screws

(10) until they click in.

AMD AM4

AM4

(Bottom view)

Notes

bequiet.com

AM2(+)

AM3(+)

FM1/FM2(+)

Product specificaties

Merk:	Be Quiet!
Categorie:	Hardwarekoeling
Model:	Shadow Rock 2
Kleur van het product:	Black, Copper colour, Silver
Gewicht:	1127 g
Breedte:	122 mm
Diepte:	160 mm
Hoogte:	147 mm
Snoerlengte:	0.22 m
Gewicht verpakking:	1470 g
Breedte verpakking:	170 mm
Diepte verpakking:	190 mm
Hoogte verpakking:	145 mm
Soort:	Koeler
Geluidsniveau (lage snelheid):	15.3 dB
Geluidsniveau (hoge snelheid:	24.9 dB
Netvoeding:	2.88 W
Materiaal:	Aluminium
Luchtstroom:	87 m³/uur
Maximum luchtstroom:	51 cfm
Aantal ventilatoren:	1 ventilator(en)
Thermal Design Power (TDP):	180 W
Rotatiesnelheid ( max):	1600 RPM
Mean time between failures (MTBF):	80000 uur
Inclusief schroeven:	Ja
Rotatiesnelheid ( min):	800 RPM
Geschikte locatie:	Processor
Ventilator diameter:	120 mm
Spanningclassificatie:	12 V
Nominale netspanning:	0.24 A
Aantal ventilatorbladen:	9
Supported processor sockets:	LGA 1150 (Socket H3), LGA 1155 (Socket H2), LGA 1156 (Socket H), LGA 1366 (Socket B), LGA 2011 (Socket R), LGA 2066, LGA 775 (Socket T), Socket 754, Socket 939, Socket 940, Socket AM2+, Socket AM3+, Socket AM4, Socket FM1, Socket FM2
Maximum luchtdruk:	1.4 mmH2O
Type lager:	Ventilatorlager
Aantal vinnen:	51
Materiaal vinnen:	Aluminium
Aantal warmte pijpen:	4
Maten ventilator (b x d x h):	120 x 120 x 25 mm
Warmte pijpen diameter:	8 mm
Heatsink afmetingen (B x D x H):	122 x 122 x 160 mm
Fan connector:	4-pin
Inclusief thermisch pad:	Ja