BDI Mirage 8227-2 Handleiding

BDI Niet gecategoriseerd Mirage 8227-2

Lees hieronder de 📖 handleiding in het Nederlandse voor BDI Mirage 8227-2 (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3
1
C - Assembled Cabinet
x 1
Mirage is engineered for easy assembly. Carefully follow this procedure
to prevent any damage.
Placement and Maintenance
Mirage is designed for indoor use on level floors. Clean glass with glass
cleaner; steel parts and painted surfaces with a moist cloth.
Step 1
Unpack and Identify
Unpack and identify the components at left. Note that some components
are shipped inside the cabinet. The assembly workspace should be a non-
marring surface such as carpet. For missing hardware pieces, please
contact BDI Customer Service at customerservice@bdiusa.com. For all
other concerns, please contact your BDI Retailer.
Step 2
Leveling and Shelf Adjustment
Component List
Designed by Al Glass and Cristian Wicha.
These distinctive product configurations are protected by US and international
patents, trade dress, and/or copyright laws.
BDI are trademarks of Becker Designed, Inc.
All Rights reserved. ©2009, BDI
Made in China. 8227-2REV100609v3
MIRAGE
8227-2
A S S E M B L Y I N S T R U C T I O N S
BDIUSA COM BDIUSA COM. CUSTOMERSERVICE@ .
B - Allen Wrench x 1
A - Phillips Screwdriver
x 1
For more information about the adjustable levelers and
troubleshooting, be sure to check out “Fine tuning your
new BDI Mirage Home Theater Furnitureat the end of
these instructions.
E- Back Panel x 2
D - Adjustable Shelf x 3
Adjustable leveler glides on
are accessible from inside
the cabinet using the Allen
Wrench (B).
The shelf pins located inside
the cabinet space may be
repositioned, allowing you to
raise or lower each shelf to the
desired level.
Shelf Pin
B
A
C
2ASSEMBLY INSTRUCTIONS
BDIUSA CUSTOMERSERVICE BDIUSA.COM @ .COM
Step 3
Back Panel Installation
Install back panel to the rear side of cabinet.
Velcro straps are included as wire management for your
convenience.
Optional Flat Panel TV Mount
This BDI cabinet is compatible with BDI’s Flat-
Panel TV Mount #9970 , (sold separately) with
the following features:
attaches easily to the back of the cabinet t
accommodates most TVs up to 60” t
swivel allows for rotating for optimal viewing t
allows adjustable TV mounting height t
accepts and route cables to and from the TV t
For more information, visit www.bdiusa.com
E
3ASSEMBLY INSTRUCTIONS
BDIUSA CUSTOMERSERVICE BDIUSA.COM @ .COM
Fine tuning your new BDI Mirage Home Theater Furniture
These steps are to be followed after you have unpackaged and completed the simple assembly instructions for your
Mirage AV stand. Due to jostling in freight or perhaps an uneven floor, the doors and drawers on your Mirage stand
may not appear to be in perfect alignment. Making a few minor adjustments can rectify this situation. Be aware
that depending on your situation, patience and a bit of trial and error are required. The high-quality European hinge
hardware is infinitely adjustable, but changing one element can cause the need for further adjustments. Through a
little adjustment, you can modify the orientation of the cabinet doors to make sure that they are sitting perfectly on
your Mirage unit.
STEP 1 - Level your Mirage unit
Levelers are integrated into each leg assembly and are accessed from inside the cabinet. If your floor is uneven, you
may extend one or more levelers (with the provided Allen Wrench) to attain a level, stable cabinet placement. Turning
the leveler clockwise will extend the leveler; turning it counter-clockwise will retract it.
STEP 2 - Adjust Door Hinges (if needed)
The doors on your cabinet should be evenly spaced and the doors should open and close freely without rubbing against
the door frame.
If the cabinet’s doors appear out of
alignment, this condition can be corrected
with minor adjustment to the European
hinges on each door.
Because these hinges are infinitely
adjustable, adjusting one hinge element can
sometimes cause the need for adjustments
to other elements. But with a few
adjustments, you can modify the orientation
of the cabinet doors to make sure that they
hang perfectly within your cabinet.
Use a Phillips screwdriver to adjust Mirage’s door hinges:
By adjusting Screw 1, the door will move LEFT or RIGHT within the frame. Make minor adjustments at both
top and bottom hinges for best results.
By adjusting Screw(s) 2, the door will move UP or DOWN within the frame (the top and bottom hinges
must be adjusted the same degree).
NOTE: If your hinges have a Slotted Mounting Plate (as shown in Figure 2): Loosen Screws 2 one
complete turn, raise or lower door, then hold in position while tightening Screws 2 (on both hinges).
By adjusting Screw 3 the entire door will move IN or OUT, opening or closing the gap between the door
frame and cabinet. (This screw rarely needs adjustment.)
INCORRECT! Door
is out of alignment
with the rest of the
unit.
CORRECT! Door is
sitting squarely and
evenly spaced on
tops and sides.
1.
2.
3.
3.
1.
2.
*
2.
*
2. 2.
3.
1.
1.
Figure 2Figure 1
3.


Product specificaties

Merk: BDI
Categorie: Niet gecategoriseerd
Model: Mirage 8227-2

Heb je hulp nodig?

Als je hulp nodig hebt met BDI Mirage 8227-2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd BDI

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd