BASSBOSS SSP118-MK3 Handleiding

BASSBOSS Speaker SSP118-MK3

Lees hieronder de πŸ“– handleiding in het Nederlandse voor BASSBOSS SSP118-MK3 (6 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 21 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/6
cutsheet
Single 18”
Powered Subwoofer
SSP118-MK3
SSP118-MK3 Cutsheet
2
Overview
The SSP118-MK3 Single 18” Powered Subwoofer gives you low frequency output to 30 Hz,
typical of an average Double 18”, from a single 18” box. Delivering output to frequencies lower
than many double 18” cabinets, each individual SSP118-MK3 does so in about half the space
and considerably less weight. This is a very practical consideration from both a size and cost
point of view.
If you’re a Mobile Professional who strives to provide superior sound quality, the SSP118-MK3
allows you to deliver premium service using less equipment and with less labor. With two
SSP118-MK3 Subwoofers, you will have the output of one of the worlds finest Double-18”
subwoofers, the BASSBOSS SSP218, divided into two smaller, more manageable pieces.
The cabinets are constructed from 18mm marine-grade Birch plywood. The cabinet is
extensively braced and construction features dado and rabbet joinery throughout, so all
seams are interlocked and the cabinet is ultra-rigid. The cabinet is finished in an extremely
rugged, black polyurea coating and the driver is protected by a black, powder-coated,
perforated steel grille.
The SSP118-MK3 features a 2500W amplifier with an auto-sensing, globally compatible
power supply that can run on mains supplies anywhere between 90 and 250 Volts. Full
output power is available on anything over 110V. The amplifier’s high peak-output voltage
Single 18”
Powered Subwoofer
SSP118-MK3
bassboss.com
3
provides for intense high SPL hits while its sustained output is unparalleled in its ability to
deliver the liquid lows. The amplifier is passively cooled via its external heat-sink and by
woofer-generated air-flow through the ports. When necessary, two blower-fans will engage
to provide additional forced-air cooling capacity in more extreme conditions.
New to the MK3 are Neutrik powerCON True 1 TOP (Total Outdoor Protection) waterproof
mains connectors. Waterproof mains connectors, along with a totally isolated input
connection section and cones that are waterproofed, make the MK3 series the powered
loudspeakers that can be used outdoors without fear of what the weather will bring. (Or used
indoors without fear of what the partiers bring.)
Electrical power is converted into the much more desirable acoustical power by a very robust,
neodymium motor, 18-inch woofer with a massive 4.5-inch (115mm) voice coil. Neodymium
magnets are lighter, and their higher intensity provides higher eξš™iciency, so the result is a
lighter and louder cabinet than those with ferrite drivers.
The MK3 features an all-new DSP. The comprehensive suite of processing includes high-
pass and low-pass filters, as well as a five-stage limiter system to prevent driver overload
in as many ways as possible, including thermal, excursion and clipping. The five levels
of protection actively prevent overheating of the voice coil, minimize long-term thermal
compression and limit excursion. Because they operate in 5 diξš™erent modes, the limiters
are sophisticated enough to have a largely unnoticable eξš™ect on the transient response and
allow the subwoofer to deliver peak output safely.
The new DSP features an Ethernet interface. This can be used to control the cabinets from
a computer or to load software or firmware updates. Each cabinet includes a two-port switch
so multiple cabinets can be chained on the same data cable The ethernet connectivity in
conjunction with the DSP board allows signal to be sent via Milan AVB. Firmware updates
will provide access to this feature.
Within the software, multiple cabinets can be grouped together, allowing them to respond to
commands simultaneously. This permits the levels of multiple loudspeakers to be adjusted
together and yet independently from the levels of other groups of loudspeakers. In addition
to individual and grouped level controls, presets can be loaded and signal levels and
temperatures can be monitored.
The MK3 DSP features storage capacity for up to 100 presets, eight of which can be accessed
at the touch of a button with no need for a connected computer. The eight directly accessible
presets are compatible with all the presets in the MK3 Top Boxes and are also compatible
with previous generation BASSBOSS tops and subs.


Product specificaties

Merk: BASSBOSS
Categorie: Speaker
Model: SSP118-MK3

Heb je hulp nodig?

Als je hulp nodig hebt met BASSBOSS SSP118-MK3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Speaker BASSBOSS

Handleiding Speaker

Nieuwste handleidingen voor Speaker