AXESS AXTC-MZ1 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor AXESS AXTC-MZ1 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
AXTC-MZ1
I N S T A L L A T I O N I N S T R U C T I O N S
AxxessInterfaces.com © COPYRIGHT 2025 METRA ELECTRONICS CORPORATION REV. 1/24/25 INSTAXTC-MZ1
INTERFACE FEATURES
TOOLS & INSTALLATION ACCESSORIES REQUIRED
• Crimping tool and connectors, or solder gun,
solder, and heat shrink
• Tape
• Wire cutter
• Zip ties
TABLE OF CONTENTS
Connections 2 ............................................................
Programming 3 .........................................................
Troubleshooting.....................................................4
Steering Wheel Control and Data Interface
Fits Mazda 2007-2016
APPLICATIONS
MAZDA
CX-5 2013-2016 ..................................................................................................
CX-7 2007-2012 ..................................................................................................
CX-9 2007-2015 ..................................................................................................
INTERFACE COMPONENTS
• AXTC-MZ1 interface
• LD-SWCX-MZ1 harness
• 3.5mm adapter Product Info
ATTENTION: With the key out of the ignition,
disconnect the negative battery terminal
before installing this product. Ensure that all
installation connections, especially the air
bag indicator lights, are plugged in before
reconnecting the battery or cycling the ignition
to test this product.
NOTE: Refer also to the instructions included
with the aftermarket accessory before
installing this device.
Visit for more detailed information AxxessInterfaces.com
about the product and up-to-date vehicle specific applications.
www.MetraOnline.com
MetraOnline.com may be used
to assist with dash assembly
instructions. Simply enter your
Year, Make, Model vehicle into the
vehicle fit guide and look for the
Dash Kit Installation Instructions.
Designed for amplified and non-amplified models
Provides accessory power (12-volt 10-amp)
Provides NAV outputs (parking brake, reverse, speed sense)
Retains audio controls on the steering wheel
Designed to be compatible with all major radio brands
Auto detects vehicle type, radio connection, and preset controls
Retains memory settings even after battery disconnection or
interface removal (non-volatile memory)
Retains balance and fade (excludes amplified models)
Retains the ability to set the clock via a service harness
Retains the factory backup camera
Micro “B” USB updatable
Green - Rear left speaker + output
Green/Black - Rear left speaker - output
Green/Purple
- Reverse Signal
Light Green - Parking brake
Orange - Illumination
Purple - Rear right speaker + output
Purple/Black - Rear right speaker - output
Gray - Front right speaker +
Gray/Black - Front right speaker -
White - Front left speaker +
White/Black - Front left speaker -
Blue -Antenna turn on
Red - Accessory power
Yellow - Battery wire
Black - Ground wire
Blue/Pink - VSS/Speed-Sense
Blue/White -
Amp turn on
Grey/Red - SWC2
SWC2
Note: The 2’ long harness with a 24-pin connector
is a service harness for setting the clock with the
factory radio. Run this harness to a location
where it can be easily accessed, yet hidden.
Front
Rear
Sub
AUX-IN
Rear View
SWC
Aftermarket Radio
(Your radio’s features may vary)
*BACK*
LD-SWCX-MZ1
ONLY FOR
2010-2012 CX-7 2010-2015 CX-9&
Connect the SWC2 wireGrey/Red
to the Antenna wire to retain Blue
Bluetooth buttons on steering wheel
20-Pin
Vehicle Connectors
Radio Connections
Interface
LED Light
Reset Button
2
CONNECTIONS: LD-SWCX-MZ1 HARNESS
3.5mm Adapter (for vehicles with Steering wheel controls or aftermarket radios with a wire for SWC)
Boss (with SWC wire): Key 1 (Gray) - Brown
Kenwood / JVC (with SWC wire): Blue/Yellow - Brown
XITE: SWC-2 - Brown
Key-A or SWC-1 - Brown
Key-B or SWC-2 - Brown/White
*After programming, assign SWC buttons within radio menu
Universal Radio*
{
3.5mm Adapter for Vehicles without Steering wheel controls
1) 3.5mm adapter Brown Brown/White From the , tie the and wires together with tape or connector
2) 3.5mm adapter LD- WCX-MZ1 HarnessConnect the to the 3.5mm jack from the S
3) AXTC-MZ1 Program the per the instructions on page 3. Disregard steps 4 & 5.
NOTE: This connector is a service plug to allow the setting of your vehicle’s clock. When you
want to change the clock, plug the white harness into the OEM radio and adjust the clock as
the vehicles owner’s manual instructs you to. After clock is set, unplug and hide the harness.
3
REV. 1/24/25 INSTAXTC-MZ1
Open the driver’s door, and keep open during the programming process.
Cycle the ignition on.
Connect the to the , and then toAXTC-MZ1 harness AXTC-MZ1 interface
the wiring harness in the vehicle.
The will enter auto-detect mode. No additional action is required.AXTC
The LED will flash & while the interface programs the radio to Green Red
the steering wheel controls. Once programmed, the LED will go out, then
produce a pattern which will identify the radio type installed. Refer to
the section under for radio typesRadio LED Feedback Troubleshooting
.
*Only applicable if vehicle came with steering wheel controls
PROGRAMMING
1.
2.
3.
4.
5*.
O
F
F
A
C
C
O
N
S
T
A
R
T
Gr Deen & Red LE
Gr Deen or Red LE
The LED will go out, then once again quickly flash & while Green Red
the interface programs itself to the vehicle. Once programmed, the LED
will go out again, then turn solid .Green
Cycle the ignition off, then back on.
Test all functions of the installation for proper operation.
6.
7.
8.
Gr Deen & Red LE
Gr Deen LE
O
F
F
A
C
C
O
N
S
T
A
R
T
O
F
F
A
C
C
O
N
S
T
A
R
T


Product specificaties

Merk: AXESS
Categorie: Niet gecategoriseerd
Model: AXTC-MZ1

Heb je hulp nodig?

Als je hulp nodig hebt met AXESS AXTC-MZ1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd AXESS

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd