Audix M3WHM Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Audix M3WHM (4 pagina's) in de categorie Microfoon. Deze handleiding was nuttig voor 65 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
AUDIX M3
INSTALLATION GUIDE
Thank you for choosing Audix! Our products are designed to provide you with many years of
reliable service. Please read this manual before using the system
for optimal installation and operation.
IN THE PACKAGE
OPTIONAL ACCESSORIES
M3 Tri-element Hanging Ceiling Microphone
JBM3 - Plenum rated junction box circuitry
Junction box lid
Breakout cable consisting of RJ45 female to three terminal block connectors
Seismic / Fire restraint cable
PLENHSEM3 Brass plenum bell housing (patent pending). This brass
housing is specically designed to provide a plenum seal when threaded on
to the plenum junction box. The bell housing is included with all Audix CAT 7
prepackaged interface cables (see below for models), and may be purchased
separately for bulk cable runs.
CBLM3XLR Breakout cable consisting of an RJ45 female to three XLR male
connectors. This cable is designed to be used in conjunction with Audix CAT
7 interface cable, keeping the shielded and balanced audio path intact when
connecting to the three mic level XLR inputs of a DSP Controller.
CAT7 Interface cable. Audix manufactures a high quality CAT 7 cable
optimized for balanced audio and cross talk elimination. The cable is LS0H
(low smoke zero halogen) and consists of four twisted pairs that are individu-
ally shielded, RJ45 male connectors and a brass housing to further seal the
cable at the plenum rated junction box. The interface cable is available in
prepackaged lengths or in bulk (see below for models).
Note: The Audix M3 also works with CAT 5 and CAT 6 cable, however, Audix recommends
using shielded cable.
CBLM307 - Interface Cable 7 meters (23’)
CBLM310 - Interface Cable 10 meters (33’)
CBLM315 - Interface Cable 15 meters (49’)
CBLM320 - Interface Cable 20 meters (66’)
CBLM325 - 25 meters (82 ) Interface Cable '
CBLM330 - Interface Cable 30 meters (98 )'
CBLM350 - Bulk cable. 50 meters (162’). Use with brass plenum bell housing #6 for best results.
CBLM3100 - As above. 100 meters (325’)
1
2
3
6
7
8
5 4
4
1
2
5
3
Fig A. Remove ceiling tile and drill
5/8” (16mm) hole in the desired
location.
Fig B. Position the JBM3 plenum
rated junction box over the
drilled hole.
Fig C. Remove the nut from
the threaded portion of the M3
cable , feed cable through the
tile hole and into the junction box.
Fig D. Install the threaded nut with
shoulder side down and secure.
Fig E. Insert the 7 pin mini female
XLR connector into the male
receptacle.
Fig F. Set the initial height of the
M3 and spool the excess cable
inside the junction box.
Fig I. Adjust the cable to exact
desired length by either feeding
or pulling the cable through the
ceiling mount.
Fig G. Fasten the lid on top
of the junction box. Insert RJ45/
Cat cable into JBM3 receptacle.
(See back page for installing
seismic cable)
Fig H. If using Audix Cat 7 LSOH
interface cable , screw on the
brass bell housing over the RJ45
connection and reset ceiling tile.
Fig K. Microphone elements are
spaced 120 degree apart. Channel
1 is directly below the Audix logo
Fig J. Position the microphone by
turning the cable as necessary and
gently turn the nut clockwise to se-
cure (1 to 2 turns). Do not over tighten.
INSTALLATION AND WIRING INSTRUCTIONS
Fig L. Connect RJ45 cables into
the breakout cable and connect to
DSP Controller.
1
8
3
2


Product specificaties

Merk: Audix
Categorie: Microfoon
Model: M3WHM

Heb je hulp nodig?

Als je hulp nodig hebt met Audix M3WHM stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Microfoon Audix

Handleiding Microfoon

Nieuwste handleidingen voor Microfoon