Audiolab 8000S Handleiding

Audiolab Receiver 8000S

Lees hieronder de 📖 handleiding in het Nederlandse voor Audiolab 8000S (4 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 71 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
8000S
Integrated Amplifier
User Instructions
Audiolab
IAG House,
Sovereign Court,
Ermine Business Park,
Huntingdon PE29 6XU
Tel: 01480 447700
Fax: 01480 431767
Mains supply and safety
Mains Supply: The mains operating voltage of all Audiolab units is
shown on the rear panel. If this does not match the voltage in your area,
consult your dealer.
The mains supply fuse is located on the rear panel of the unit. If it has
broken, check for any obvious cause before replacing the fuse with one of
the correct rating and type. The fuse values are:
220 - 240V (UK, Korea, etc.) T 2.5AL 20mm Slow Blow
100 - 120V (USA, Japan, etc) T 4.0AL 20mm Slow Blow
The fuse is located in a slide-in
carrier which also contains a spare
fuse. The fuse carrier can only be
pulled out after the IEC power cord is
unplugged. When the carrier is
opened the first fuse to be seen is the
spare fuse. Remove and safely
dispose of the fuse with the blown
link before replacing it.
Class II construction double insulated. This product must not be
connected to earth.
Power Cord: An AC power cord is normally supplied with a mains plug
suitable for your area. If you have any doubts, consult your dealer about
obtaining a suitable power cord.
Important notice to UK users
The appliance cord is terminated with a UK approved mains plug fitted
with a 5A fuse. If the fuse needs to be replaced, an ASTA or BSI approved
BS1362 fuse rated at 5A must be used. If you need to change the mains
plug, remove the fuse and dispose of this plug safely immediately after
cutting it from the cord.
Connecting a Mains Plug
The wires in the mains lead are coloured in accordance with the code:
Blue: NEUTRAL; Brown: LIVE:
As these colours may not correspond to the coloured markings identifying
the terminals in your plug, proceed as follows:
The BLUE wire must be connected
to the terminal marked with the
letter N or coloured BLUE or
BLACK. The BROWN wire must be
connected to the terminal marked
with the letter L or coloured
BROWN or RED.
2.5A FUSE
BS 1362
BROWN
(Live)
BLUE
(Neutral)
Fuse Carrier
IEC Mains Connector
Use only attachments/accessories specified by the manufacturer.
Use only with a cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for long
periods of time.
Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-
supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
Warning: To reduce the risk of fire or electrical shock, do not expose this
product to rain or moisture. The product must not be exposed to dripping
and splashing and no object filled with liquids such as a vase of flowers
should be placed on the product.
No naked flame sources such as candles should be placed on the
Read these instructions. product.
Keep these instructions. In the event that you pass the product to a third Caution: Changes or modifications not expressly approved by the
party this instruction manual should be provided along with the product. manufacturer could void the user's authority to operate this device.
Heed all warnings. This equipment has been tested and found to comply with the limits for a
Follow all instructions. Class B digitial device, pursuant to part 15 of the FCC rules. These limits
Do not use this apparatus near water. are designed to provide reasonable protection against harmful
Clean only with dry cloth. interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
Do not block any ventilation openings. accordance with the instructions, may cause harmful interference to radio
Install in accordance with the manufacturer's instructions. or television reception, which can be determined by tuning the equipment
Do not install near any heat sources such as radiators, heat registers, off and on, the user is encouraged to try to correct the interference by one
stoves, or other apparatus (including amplifiers) that produce heat. or more of the following measures:
Do not defeat the safety purpose of the polarized or grounding type plug. Re-orientate or re-locate the receiving antenna. Increase the separation
A polarized plug has two blades with one wider than the other. A between the equipment and the receiver. Connect the equipment into an
grounding type plug has two blades and a third grounding prong. The outlet on a circuit different from that to which the receiver is connected.
wider blade or the third prong are provided for your safety. If the provided Consult the dealer or an experienced radio/TV technician for help.
plug does not fit into your outlet, consult an electrician for replacement of
the obsolete outlet. Important Note: The batteries supplied with this unit should be treated
Protect the power cord from being walked on or pinched, particularly at with care and not punctured or damaged. Used batteries should be
plugs, convenience receptacles, and the point where they exit from the disposed of in full conformity with recycling regulations in your area.
apparatus. NEVER dispose of batteries in a fire or in the general rubbish.
CAUTION!
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ADVERTISSEMENT: RISQUE DE CHOC ELECTRIQUE-
NE PAS OUVRIR
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER
NO USER-REMOVEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED PERSONNEL
This symbol indicates that there are important
operating and maintenance instructions in the
literature accompanying this unit.
This symbol indicates that dangerous voltage
constituting a risk of electric shock is present
within this unit.
1: Statutory & Safety Information
Rated Output Power Headphone Output
60 W (18 dBW) per channel into rated load impedance (8 Ohms) Output impedance: 330 W
with both channels driven (Suitable for headphones 8 W-2 k impedance)W
Record Output
Inputs
VIDEO OUT, TAPE 1 OUT, TAPE 2 OUT:
CD, TUNER, AUX, VIDEO, TAPE 1, TAPE 2: 125mV/20k IHFW
Output impedance: 1 k . W
POWER AMP: 782 mV/47 kW
Gain from input to record output 0 dB (x1)
Gain Muting
PRE-AMP: 9dB@ 1 kHz Muting controlled manually or automatically
POWER AMP: 29.0 dB @ 1 kHz. Accessories Supplied
Signal To Noise Ratio AC Power Cord
CD, TUNER, AUX, VIDEO, TAPE 1, TAPE 2: Instruction Manual
Better than 80dB(IHF, rel. 0.5 V pre-amp output) 8000RC Remote Control with 2 x AA batteries
POWER AMP: better than 80dB(IHF, rel. O dBW) Colour
Frequency Response Silver
CD, TUNER, AUX, VIDEO, TAPE 1, TAPE 2 and POWER AMP: Operating Temperature Range
20 Hz-20 kHz ±0.5 dB: 1 Hz-65 kHz -3 dB. 10-35 °C
Total Harmonic Distortion & Noise Power Requirements (Depending on Region)
Less than 0.07 % 50-60Hz 100 V, 110-120 V, and 220-240 V models available
Channel Balance Maximum Power Consumption: 440 VA
Within 1 dB Dimensions (WXHXD)
Channel Separation 445x74x335 mm - including feet, terminals and controls
Better than 60 dB @ 1 kHz any input 445 x 64 x 302 mm- excluding feet, terminals and controls
Crosstalk Weight
Better than 80 dB @ 1 kHz Net: 7.4 kg
Polarity (phase) Shipping: 8.8 kg
Non-inverting for all inputs and outputs Audiolab reserves the right to alter design and specification
Pre-amp Output without notice. Specification may vary for different countries.
PRE OUT 1 and PRE OUT 2: Output Impedance 100 WAudiolab is a member of the International Audio Group.
Maximum Output >7.3 V RMS
6: Specifications 8000S
Power Amplifier Protection Circuits
Short Circuit Protection: If the output terminals are connected together or there
is a short caused by a faulty speaker or connecting lead, the amplifier will mute and
un-mute until the fault condition is removed.
DC Offset Protection: If there is an internal or external fault which may cause DC
voltage to be presented to the loudspeaker, the amplifier will mute and stay muted
until the fault is removed.
Thermal Protection: If the amplifier is driven excessively for long periods, or the
output devices are pushed beyond their safe operating area, the amplifier will
switch off and then switch back on again when it has cooled down.
In all cases, if the amplifier does not respond to remedial action, consult your dealer.
Volume
Press to raise or lower the volume. The
VOLUME control on the front panel turns.
Unpacking Always switch the power off before changing connections.
Input Selector
Unpack the product fully. The carton should contain
Turn to select the listening source. The 8000S mutes briefly when a
(The Audiolab 8000S integrated amplifier
new input is selected.
(One IEC power cord suitable for your area
Volume Control
(One Remote Handset with two AA batteries
(Adjusts playing volume. Always turn the volume up gradually.This instruction manual.
Record Selector
If any item is missing or damaged report this to your dealer as
soon as possible. Turn to select source to record to Tape 1, Tape 2 or Video. The
Retain the packing for future safe transport of your amplifier. If connections can also be used to connect to any recorder with
you dispose of the packing, do so with regard to any recycling analogue inputs such as a CD, MP3, DAT recorder, etc.
regulations in your area. Record selector and input selector operate independently. It is
Inserting Batteries in the Handset possible to record from any source whilst listening to another.
Mode Switch
The battery compartment is on the rear of the handset. Unwrap the
Select integrated when using 8000S as an integrated amplifier.
batteries, open the compartment cover and insert the batteries.
Select mute to turn off pre-amplifier outputs, loudspeakers or
Follow the polarity indications in the battery compartment. headphones. See section 4 for further details.
Always replace batteries in pairs. Use new batteries of the same
Headphone Socket
type and rating, ideally from the same manufacturer.
Socket for connection of headphones. Unplug headphones when
Controls And Functions not in use. Connecting headphones mutes the loudspeakers and
Power Switch disconnects the pre-amplifier outputs and power amplifier inputs.
When power is switched on the 8000S is muted for 8 seconds.
2: Introduction
5: Service and Warranty
RECORD
SELECTOR
INPUT
SELECTOR
MODE
SWITCH
VOLUME
CONTROL
HEADPHONE
SOCKET
POWER
SWITCH
POWER LED
RED=Power On
MUTE LED
RED=Mute On
REMOTE
CONTROL SENSOR
Input
Press to select listening source. The INPUT
selector on the front panel turns.
If you wish to record, the record input must be
selected manually.
Mute
Toggles mute On/off. Does not function if the
MODE switch on the front panel is set to mute.
Remote Handset
Buttons shown in white control the 8000S.
Buttons shown in grey operate Audiolab CD
players and have no effect on the 8000S.
As the handset uses RC5 coding it will operate
many other players. Check with your dealer.
Servicing
Servicing of Audiolab products should only be carried out by
authorised service agents. If service is required the equipment
should be returned, securely packaged, preferably using original
packaging, to your dealer.
In the UK equipment may be returned to the IAG Service Centre. In
the USA equipment may be returned to the Service address shown
on this page.
Always telephone before returning any equipment.
A note should be enclosed giving your name, address, telephone
number, and a brief description of the reason for return.
If you require Service outside the Warranty period, do not hesitate
to contact your dealer.
While cleaning is in progress the AC power cord must be
unplugged from the AC power supply socket.
Any grease or dirt on the equipment may be removed with a soft,
lint-free cloth slightly moistened with a mild solution of warm
water and detergent or washing-up liquid. Do not use any other
solutions or solvents.
Retain original packaging for transporting equipment.
If you have any queries regarding the use of Audiolab equipment,
consult your dealer.
Service Addresses, UK & USA
IAG Service Centre
Unit 4
St Margaret’s Way
Stukeley Meadows Industrial Estate
Huntingdon
Cambs
PE29 6EB
England
452561
13403
Tel:+44 (0)1480
Fax: +44 (0)1480
IAG America, Inc.
15 Walpole Park South
Walpole
MA 02081
USA
Tel: +1 508 850 3950
Fax +1 508 850 3905
Audiolab limited warranty Audiolab or its authorised agents or distributors.
!Products not purchased from an Audiolab authorised dealer.
Audiolab Ltd. warrants this product, subject to the terms and !Products that were not new at the time of original purchase.
conditions below, to be free from defects in materials and !Products sold 'as is', 'as seen' or 'with all faults'.
workmanship. During the warranty period Audiolab will repair or
Repairs or replacements as provided under this warranty are the
replace (at Audiolab's option) this product, or any defective part in
this product, if it is found to be defective due to faulty materials, exclusive remedy of the consumer. Audiolab shall not be liable for
any incidental or consequential damages for breach of any express workmanship or function. The warranty period may vary from
country to country. or implied warranty in this product. Except to the extent prohibited
by law, this warranty is exclusive and in lieu of all other warranties
Terms and conditions: whatsoever, both express and implied, including, but not limited
The warranty starts on the date of purchase (or the date of delivery to, the warranty of merchantability and fitness for a practical
if this is later). purpose.
You must provide proof of purchase / delivery before work can be This warranty provides benefits that are additional to and do not
carried out. Without this proof, any work carried out will be affect your statutory rights as a consumer.
chargeable to you. Some countries and US states do not allow the exclusion or
All work will be carried out by Audiolab or its authorised agents or limitation of incidental or consequential damages or implied
distributors. Any unauthorised repair or modification will void this warranties so the exclusions in the paragraph above may not
warranty. apply to you. This warranty gives you specific legal rights, and you
If any part is no longer available it will replaced with a functional may have other statutory rights, which vary from state to state or
replacement part. country to country.
Any parts that are replaced will become the property of Audiolab. How to claim:
Any repair or replacement under this warranty will not extend the
To obtain warranty service contact the Audiolab authorised dealer period of warranty.
from which you purchased this product. Do not despatch goods
This warranty is valid only in the country of purchase, applies only to
without the prior agreement of the dealer, Audiolab or their
the first purchaser and is not transferable.
authorised distributors.
The following are not covered: If asked to return products for inspection and/or repair, pack
!Products on which the serial number has been removed, carefully, preferably in the original cartons or packaging affording
altered or otherwise made illegible. an equal degree of protection, and return prepaid. If unsuitable
!Normal wear and tear and cosmetic damage. packaging is used, Audiolab may make a charge for the supply of
!Transportation or installation of the product. new packaging.
!Accidental damage, faults caused by commercial use, acts of Insurance is recommended as goods are returned at owner's risk.
God, incorrect installation, connection or packaging, misuse, Audiolab or their authorised distributors cannot be held liable for
neglect or careless operation or handling of the product which loss or damage in transit.
is not in accordance with Audiolab's user instructions.
Packing, insurance and freight on the return journey will be paid by
!Equipment that has been operated in conjunction with
Audiolab or their authorised agents or distributor if corrective work unsuitable, inappropriate or faulty apparatus.
!Repairs or alterations carried out by parties other than proves to be necessary.

Product specificaties

Merk: Audiolab
Categorie: Receiver
Model: 8000S

Heb je hulp nodig?

Als je hulp nodig hebt met Audiolab 8000S stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Receiver Audiolab

Audiolab

Audiolab 9000Q Handleiding

9 December 2024
Audiolab

Audiolab 8300A Handleiding

7 Juni 2024
Audiolab

Audiolab Omnia Handleiding

1 Mei 2023
Audiolab

Audiolab 6000A Handleiding

28 Februari 2023
Audiolab

Audiolab 9000A Handleiding

22 Februari 2023
Audiolab

Audiolab 8000S Handleiding

10 Januari 2023
Audiolab

Audiolab 6000A Play Handleiding

17 Oktober 2022

Handleiding Receiver

Nieuwste handleidingen voor Receiver

Monitor Audio

Monitor Audio IA40-3 Handleiding

17 December 2024
Ram Audio

Ram Audio DALIMa 10Q Handleiding

16 December 2024
Power Dynamics

Power Dynamics PAM2004 Handleiding

15 December 2024
JBL

JBL Loud and Clear LCA504 Handleiding

14 December 2024
JBL

JBL Power P-4040 Handleiding

14 December 2024
JBL

JBL Grand Touring GTS100 Handleiding

14 December 2024
IFi Audio

IFi Audio ZEN Can Signature HD6XX Handleiding

12 December 2024
Phonic

Phonic DMX2502 Handleiding

11 December 2024
Phonic

Phonic ICON 700 Handleiding

11 December 2024
Phonic

Phonic DMA8425 Handleiding

11 December 2024