AS Synthesizers Lowpass VCF & VCA AS201 Handleiding

AS Synthesizers Niet gecategoriseerd Lowpass VCF & VCA AS201

Lees hieronder de 📖 handleiding in het Nederlandse voor AS Synthesizers Lowpass VCF & VCA AS201 (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 135 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3
BLOCK DIAGRAM OF
LOWPASS VCF & VCA
AS201
100% ANALOG MODULE
12345
6 7 8 9 10
14
11
21 22
15
19
20
17 18
16
13
12
1. V/OCT CV input, range: 0V to +10V,
2. FREQ CV1 input, range: -10V to +10V
3. FREQ CV2 input, range: -10V to +10V
4. RESO CV input, range: 0V to +10V,
5. VCA CV input, range: 0V to +10V
6. VCF audio in 1, level: 10Vpp
7. VCF audio in2, level: 10Vpp
8. VCF audio in 3, level: 10Vpp
9. VCF audio out
10. VCA audio out
11. Freq CV1 depth: 0 to 100%
12. Freq CV2 depth: 0 to 100%
13. Reso CV depth: 0 to 100%
14. Level of VCF audio in 1: 0 to 100%
15. Level of VCF audio in 2: 0 to 100%
16. Level of VCF audio in 3: 0 to 100%
17. Cutoff freq potentiometer
18. Resonance potentiometer
19. VCF slope switch
20. VCF drive indicator
21. Q compensatin switch
22. FREQ CV2 to VCA CV switch
FRONT PANEL OF
LOWPASS VCF & VCA
AS201
100% ANALOG MODULE
7
6
5
1
3 2
4
1. Power bus connector IDC10
2. Initial tune
3. V/OCT scale trim
4. Multimeter probe pins
5. CV inputs from internal rails
6. VCF inputs from internal rails
When no use of input pins, connect
jumper between input and GND also
between V/OCT IN and V/OCT REF pins
7. VCF & VCA outputs to internal rails
Do not use jumpers on output
pins, also do not connect to ground or
power rails!
TECHNICAL SPECIFICATION:
Module depth: 33mm
Module width: 16HP (80.4mm)
Module weight: 215g
Connector type: 10P IDC Eurorack
Power consumption:
+12V / 60mA & 12V / 50mA
Audio in & out: HQ Audio
Audio in & out range: 10Vpp
CV inputs: 0V to +10V or -5V to +5V
CALIBRATION: The best results for fi lter range,
the voltage on “SCALE” probe should be
maintained -25mV and +155mV
This voltage difference is 180mV
1. Turn down all knobs into fully CCW
position, disconnect cables from V/OCT
input. Take care of the jumper to be
connected between V/OCT IN and
V/OCT REF pins on backside of the
module
2. Power on your modular system, and wait
a few minutes for warm up
3. Connect multimeter’s GND probe
to any GND pin, or connector. Next,
connect multimeter’s positive probe
to “SCALE” probe
4. Turn Cutoff Freq knob into fully CCW
position, measure +155mV
5. Turn Cutoff Freq knob into fully CW
position, measure -25mV
6. In case you see different value, then turn
“SCALE” trimmer until voltage difference
between full CCW and full CW
becomes 180mV
7. Now turn “INIT” trimmer until measure
+155mV at full CCW of Cutoff Freq knob,
and -25mV at full CW,
8. Enjoy
BACK PANEL OF
LOWPASS VCF & VCA
AS201
100% ANALOG MODULE


Product specificaties

Merk: AS Synthesizers
Categorie: Niet gecategoriseerd
Model: Lowpass VCF & VCA AS201

Heb je hulp nodig?

Als je hulp nodig hebt met AS Synthesizers Lowpass VCF & VCA AS201 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd AS Synthesizers

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Electrolux

Electrolux STA9 Handleiding

23 November 2024
Electrolux

Electrolux UMP3 Handleiding

23 November 2024
Bosch

Bosch HEZ8TK36UC Handleiding

23 November 2024
Bosch

Bosch HEZ8ZZ36UC Handleiding

23 November 2024
Bosch

Bosch HDZIT301 Handleiding

23 November 2024
Bosch

Bosch HEZBS301 Handleiding

23 November 2024
LG

LG LX-330 Handleiding

23 November 2024
Bosch

Bosch KSZ2AVU00 Handleiding

22 November 2024