Arlec DC681 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Arlec DC681 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 37 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
5 6
Introduction
The Wireless Door Chime (DC681) consists
of t wo separate units:-
1. Push Button Unit
(Transmitter)
2. Chime Unit
(Receiver)
These units are completely self-contained
and no wiring bet ween them is necessary.
Range
Up to 50 metres.
NOTE: Range depends on location,
temperature, and battery condition.
Important Notes
1. The operation and range of your Wireless Door Chime depends on location,
temperature and bat tery condition.
2. Try different locations in your home, ideally more than 1 metre from the floor.
Move Chime unit closer to Push But ton unit to improve operation.
3. Do not expose either unit to rain or immerse in water.
4. Avoid locations where the Push But ton unit is exposed to direct summer sunlight.
5. Do not leave exhausted batteries in Push But ton unit.
6. Clean only with a damp cloth and mild detergent. Do not use solvents.
7. In an event of power outage, surge or unstable main power supply, your door chime
will default to factory setting. Please reset the unit according to Resetting the Unit’.
Security
When you are away from home for long periods you may wish to leave your Chime Unit
with one of your neighbours so that they can monitor callers to your house during
your absence.
Trouble Sooting & User Hints
Problem Possible Cause Suggested Remedy
Chime
does not
sound.
1. Units are out of range (max.
range 50m) .
Operate the Chime unit within the
operation range (50m).
2. Push Button and Chime units
are not on same frequency
coding.
Re-set the frequency coding (see Code
Selection) or select a dif ferent tone (see
Tone Selection).
3. Flat Push Button bat tery. Change the batt ery.
4. Wrong polarity of bat tery in
Push Button.
Re-insert bat tery with polarity to match
markings.
5. Power outage, surge or
unstable main power supply. Re-set unit according to
‘Resetting the Unit’.
Chime
sounds
without
Push
Button
being
pressed
1. A power interruption to the
Door Chime unit plus a similar
door chime product operating
nearby has caused the chime
unit to reset to the incorrect
House Code
A. Switch off the Chime Unit for at least
1 minute. Switch on again. It should
beep twice. Press the Push Button to
operate the chime. This re-sets the
House Code in the Chime Unit or;
B. Re-set the frequency coding (see Code
Selection
2. A similar Wireless Door Chime
product is operating nearby on
the same House Code.
Re-set the House Code
(see Code Selection).
3. Interference from CBs, Taxis or
remote control toys operating
on the same frequency.
Re-set the House Code
(see Code Selection).
CPIN002793
Plug-In Wireless Door Chime
with Gloss White Finish
DC681
Installation & Operating
Instructions
CPIN002793
Warranty
Arlec guarantees this product in accordance with the Australian Consumer Law.
Arlec also warrants to the original first purchaser of this product (“you”) from a retailer that
this product will be free of defects in materials and workmanship for a period of 12 months
from the date of purchase; provided the product is not used other than for the purpose, or in
a manner not within the scope of the recommendations and limitations, specified by Arlec,
is new and not damaged at the time of purchase, has not been subjected to abuse, misuse,
neglect or damage, has not been modified or repaired without the approval of Arlec and has
not been used for commercial purposes (Warranty”).
If you wish to claim on the Warranty, you must, at your own expense, return the product, and
provide proof of original purchase and your name, address and telephone number, to Arlec at
the address below or the retailer from whom you originally purchased the product within 12
months from the date of purchase.
Arlec will (or authorise the retailer to) assess any claim you may make on the Warranty in the
above manner and if, in Arlec’s reasonable opinion, the Warranty applies, Arlec will at its own
option and expense (or authorise the retailer to) replace the product with the same or similar
product or repair the product and return it to you or refund the price you paid for the product.
Arlec will bear its own expenses of doing those things, and you must bear any other expenses
of claiming on the Warranty.
The Warranty is in addition to other rights and remedies you may have under a law in relation
to the product to which the Warranty relates.
Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and for compensation for
any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure.
Arlec Australia Pty. Ltd. ACN 009 322 105 (“Arlec”) gives the Warranty.
Arlecs telephone number, address and email address are:
Customer Service: (03) 9982 5111
New Zealand Toll Free: 0800 003 329
Building 3, 31 41 Joseph Street, Blackburn North, Victoria, 3130
Blackburn North LPO, P.O. Box 1065, Blackburn North, 3130
Email: custservice@arlec.com.au
Code Selection
The push button unit generates random code sequences to which the chime unit is
able to learn. Should your door chime unit activate intermittently for no apparent
reason, the uncontrolled activation may be caused by another unit nearby or from a
device operating on the same frequency.
Code/Push Button Limiting Switch
Your door chime unit is capable of working with a
maximum of 4 Bell Push But ton units at 4 different
frequency channels. If your door chime unit activate
intermit tently for no apparent reason, it might caused by
a nearby device working on a similar frequency channel.
To eliminate frequency channel interruption, Code/Bell
Push Button Limiting Switch is to limit the Bell Push
But ton unit and /or frequency channel that your door
chime unit can be activated by.
1. Connect the Door Chime to the mains power and press
the Bell Push Button once, the door chime will sound
to indicate that 1st operating code is registered and
memorized. This is the factory setting and intended
to limit the activate frequency channel and Bell Push
But ton unit to 1.
2. To register 2nd Bell Push Button operating code
and/or frequency channel, Press and hold the code setting switch on the door
chime unit for 1 second, it will give a “Beep” sound to indicate that door chime
is ready to learn the 2nd operating code, press the 2nd Bell Push Button once,
the door chime will sound to indicate that 2nd operating code is registered and
memorized. This will allow 2 dif ferent Bell Push Button units and /or frequency
channels working with the door chime at the same time.
3. Repeat the same procedure for the 3rd and 4th Bell Push But tons. The maximum
amount of Bell Push But ton units and frequency channels that the door chime
unit can be work at the same time are 4.
4. To reset Code/Bell Push But ton limiting function, disconnect the door chime unit
from mains power for at least 1mins, and reconnect, this will reset the door chime
unit to learn 1 Bell Push Button and/or frequency channel only.
Note: Power outage, surge or unstable main power supply will erase or rest the Code/
Bell Push Button limiting function, and low battery in push button unit will also erase
or rest the registered frequency channel between the door chime and push button
unit, if the door chime unit does not sound when push button unit depressed, please
unplug the door chime unit from power point, replace batteries on push button unit,
then re-plug the door chime unit into power point and set up both units again.
Resetting the Unit
To avoid uncontrolled activation:
1. Switch off the Chime Unit for at least 1 minute.
2. Switch back on. A double beep should be heard indicating that the unit is in
learning mode.
3. Press the Push But ton. The chime should sound to indicate code selection.
432
WARNING
This product contains a Lithium Coin type battery.
WARNING! Please ensure the coin battery is kept OUT OF REACH OF CHILDREN.
The battery presents a significant choking and burn hazard to young children
should they swallow a battery. Under 4 year-olds are especially prone to
accidental swallowing of objects such as these.
If a lithium coin battery is swallowed, SEEK IMMEDIATE MEDICAL ATTENTION.
Do not let the child eat or drink; Do not induce vomiting.
To keep your children safe:
• Keepdevicesthatusecoinbatteriesoutofreachofsmallchildren
• Keepnewbatteriesintheirpackaginguntilreadytouseandstore
in places out of reach of children
• Safelydisposeofspentbatteriesimmediately
• Sharethisinformationwithyourfamily,friends,caregiversandbabysitters.
We have designed the coin battery holder to require dexterit y normally beyond that
of a small child to access, but nevertheless you should always follow the advice
given above.
Push Button
1. Push Button unit is operated by 1 x 3 volt Lithium battery (CR2032 - included).
2. Remove the back of case by pushing in the tab on the bot tom with a small, flat
screwdriver.
3. The 3 volt Lithium bat tery (CR2032) is already installed.
Simply pull off the isolation strip which will allow the battery to make electrical contact.
NOTE: When the push button unit is depressed, an orange LED light will lit on, but this
is not an indicator of the push button unit battery level. It is recommended to replace
batteries once a year to ensure range and transmission reliability.
To Replace the Battery
Remove the locking screw from the bat tery holder clip and remove old
batter y. Insert 1 x 3 volt Lithium bat tery (t ype CR20 32) in the battery
compartment, ensuring the battery polarity is correct as in Figure 1.
Replace clip and tighten locking screw to hold bat tery firmly in place.
Chime Unit
The Chime Unit is powered by 24 0 volt and should be plugged into any
convenient household power point.
INSTALLATION
Chime Unit
Plug the Chime Unit into any household power point and switch power on. The
Chime Unit indicator lamp will glow and it will beep twice to indicate it is ready.
Press the push but ton unit to test the chime.
NOTE: Do not mount the chime and push button unit near metal objects, UPVC frame,
heat/radio source, security door or in close proximity to any radio emitting equipment.
The range of the unit may be substantially reduced.
Push Button Unit
The Push Button unit has t wo mounting holes on rear plate of unit that must be
pushed through before unit can be mounted.
1. Remove rear plate of unit (see bat tery installation).
2. Push through tabs in mounting holes.
3. Using the back plate of the Push Button unit as a guide, mark the position
of holes onto mounting surface.
4. Drill appropriately sized holes and insert wall plugs if required.
5. Secure the back plate of Push Button unit to mounting unit.
6. Clip Push But ton unit to back plate.
Alternatively the Push But ton unit can be at tached to smooth mounting surfaces such
as painted wood, glass and plastic using Self-Adhesive Pad (supplied).
Do not mount the push button unit on metal or near metal door frame, securit y door,
metal furniture or in close proximit y to any radio emit ting equipment.
The range of the unit may be substantially reduced.
Door Chime Operation
Once the Push Button and Chime units have been installed in their desired locations,
the system is ready for use.
Depress but ton on Push But ton unit momentarily, and chime should sound. Press button
again to repeat. Continual pressing of the button will not repeat the chime. If chime
fails to sound, check bat teries in push button and check power is on to Chime Unit.
Tone Selection
The Wireless Door Chime is supplied with 8 built-in chimes.
Westminster Chime Twinkle Twinkle
Double Ding-Dong It’s a Small World
Circus Theme Dog Barking
Banjo on My Knee Telephone Ring
To change the chime tune, remove the Push Button Unit ’s rear cover.
Inside the Push But ton Unit locate the small Tune Selector push button marked ‘S
(Ref. Figure 1). Each time that this Tune Selector push button is pressed, the next of
the 8 melodies will be played. You can step through and listen to each in turn. When
you hear the melody you wish to choose, do not press the tune selector again. The
chime will play the selected melody each time the bell press is pushed. At any time
you can select another melody by repeating the tune selector but ton process.
Ret the Push But ton Unit rear cover.
Whenever the Push Button Unit bat tery is fitted or replaced, the chime tune may
default to the Westminster Chime.
Fig 1.
S
CPIN002793
Code/Bell Push Button
Limiting Switch


Product specificaties

Merk: Arlec
Categorie: Niet gecategoriseerd
Model: DC681

Heb je hulp nodig?

Als je hulp nodig hebt met Arlec DC681 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Arlec

Arlec

Arlec DC681 Handleiding

12 Augustus 2023
Arlec

Arlec RT500 Handleiding

12 Augustus 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd