Appa 62 Handleiding

Appa Multimeter 62

Lees hieronder de 📖 handleiding in het Nederlandse voor Appa 62 (6 pagina's) in de categorie Multimeter. Deze handleiding was nuttig voor 24 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/6





Safety Information

Understand and follow operating instructions carefully.

Use the meter only as specified in this manual; other-

wise, the protection provided by the meter may be

impaired.



 WARNING

˙ When using test leads or probes, keep your fingers

behind the finger guards.

˙ Remove test lead from Meter before opening the

battery door or Meter case.

˙ Use the Meter only as specified in this manual or the

protection by the Meter might be impaired.

˙ Always use proper terminals, switch position, and

range for measurements.

˙ Never attempt a voltage measurement with the test

lead inserted into the A input terminal.

˙ Verify the Meter’s operation by measuring a known

voltage. If in doubt, have the Meter serviced.

˙ Do not apply more than the rated voltage, as

marked on Meter, between terminals or between

any terminal and earth ground.

˙ Do not attempt a current measurement when the

open voltage is above the fuse protection rating.

Suspected open circuit voltage can be checked with

voltage function.

˙ Only replace the blown fuse with the proper rating

as specified in this manual.

˙ Use caution with voltages above 30 Vac rms, 42

Vac peak , or 60 Vdc. These voltages pose a shock

hazard.

˙ To avoid false readings that can lead to electric

shock and injury, replace battery as soon as low

battery indicator

<<appears.

˙ Disconnect circuit power and discharge all high-

voltage capacitors before testing resistance,

continuity, diodes, or capacitance.

˙ Do not use Meter around explosive gas or vapor.

˙To reduce the risk of fire or electric shock do not

expose this product to rain or moisture.

Symbols as marked on the meter and

Instruction card



 Risk of electric shock



 See instruction card

 DC measurement



 Equipment protected by double or reinforced

insulation

<< Battery



 Fuse



 Earth

<AC measurement



 Conforms to EU directives

Do not discard this product or throw away

Measuring AC/DC Voltage And

Frequency



Warning

Warning

WarningWarning

. . . . . .

. . . . . .. . . . . . . . . .

. . . .

. . . . . . . .

. . . .

. . . . . . . .

. . . . . .

. . . . . .. . . . . .

. . . .

. . . . . . . .

. . . . . .

. . . . . .. . . . . .

. . . .

. . . . . . . .

. . . .

. . . . . . . .

Safety sheet

Safety sheetSafety sheet

. . . .

. . . . . . . .

. . . . .

. . . . . . . . . .

. . . .

. . . . . . . .

. . . . . .

. . . . . .. . . . . .

. . . .

. . . . . . . .

. . . . . .

. . . . . .. . . . . .

. . . .

. . . . . . . .

. . . .

. . . .. . . .

. . . .

. . . . . . . .

. . . . .

. . . . .. . . . .





Read First

Testing for Continuity and Diode

APPA

61/62/62T /62R Instruction

Digital Multimeter Card

Resistance

and Capacitance

(Capacitance for 62, 62T, 62R only)

BlackRedBlackRed

Black

Red

Black

Red

Bad Diode

Good Diode

Note – To improve the measurement accuracy of small

value capacitor, record the reading with the test leads

open then substract the residual capacitance of the

Meter and leads from measurement.

CUNKNOWN = CMEASUREMENT

- CRESIDUAL

MIN MAX Record (For 62, 62T, 62R only)



 Caution

˙ Disconnect the test leads from the test points before

changing the position of the function rotary switch.

˙ Never connect a source of voltage with the function

rotary switch in Ω/ ;/ A // Hz position.

˙ Do not expose Meter to extremes in temperature or

high humidity.

˙ Never set the meter in  A function to measure

the voltage of a power supply circuit in equipment

that could result in damage the meter and the

equipment under test.

Maintenance

Do not attempt to repair this Meter. It contains no

user-serviceable parts. Repair or servicing should

only be performed by qualified personnel.

Cleaning

Periodically wipe the case with a dry cloth and

detergent. Do not use abrasives or solvents.

Disable Auto Power Off

NCV

1. Volt sense switch will be activated on any function

or at OFF status.

2. Test leads are not used for the Volt sense test.

3. Press the Volt sense button. The display goes

black, a tone sounds and the red LED lights up to

verify the instrument is operational. The Volt sense

button must be held down to detect the presence

of voltage without use of the leads.

4. If a voltage of 50V to 600V (50 to 500Hz) is

detected near the top of meter a continuous tone

sounds and the red LED near the top of meter

Illuminates.

Fuse Replacement (For 62, 62T, 62R only)

Refer to the following figure to replace fuse :

Battery Replacement

Refer to the following figure to replace the batteries :



 Caution

˙ Replace the batteries as soon as the low batteries

indicator "<" appears, to avoid false reading.

˙ Batteries 1.5V x 2



 Caution

˙ Use only a fuse with the amperage, interrupt,

voltage, and speed rating specified.

˙ Fuse rating : 10A, 500V

Non-Contact Voltage (Volt sense)

Auto Power Off (Battery Saver)

Manual Ranging and Auto Ranging

10 min

Specifications

General Specifications

Display : 2000 counts.

Polarity Indication : Automatic, positive implied,

negative indicated.

Overrange Indication : “OL” or “-OL”.

Batteries

Life : Alkaline 250 hours

Low Batteries Indication : “<” is displayed when

the batteries voltage drops below operating voltage.

Auto Power Off : Approx 10 minutes.

Operating Ambient : Non-condensing ≦

≦

≦≦50F,

51.8F ~ 86F (≦

≦

≦≦80% R.H) 87.8F ~ 104F (≦

≦

≦≦75% R.H),

105.8F ~ 122F (≦

≦

≦≦45% R.H)

Storage Temperature : -4F to 140F , 0 to 80%

R.H. when battery removed from Meter.

Temperature Coefficient :

0.15 x (Spec.Accy) / F ,< 64.4F or > 82.4F.

Measure : Samples 2 times per second nominal.

Altitude : 6561.7 ft (2000m)

Safety : Complies with EN61010-1, UL61010-1,

IEC 61010-1,

V/Ω : CAT.III. 600V, CAT.II. 1000V.

A : CAT.III. 500V (for 62/62T/62R only)

Pollution degree : 2

Power Requirements :

1.5V x 2 IEC LR03, AM4 or AAA size

Dimensions (W x H x D) : 74mm x 156mm x 44mm

Weight : (320g) including battery.

Accessories : Battery (installed), Test leads and

user manual.

Measuring DC / AC Current

(For 62, 62T, 62R only)

Disconnect

Temperature °C ,°F

DCV

Display Hold

Product specificaties

Merk:	Appa
Categorie:	Multimeter
Model:	62

Heb je hulp nodig?

Als je hulp nodig hebt met Appa 62 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Multimeter Appa

19 Februari 2023

12 Februari 2023

29 Januari 2023

28 Januari 2023

6 November 2022

31 Oktober 2022

30 Oktober 2022

15 September 2022

4 Oktober 2022

Appa 99 II Handleiding

15 September 2022

Handleiding Multimeter

Nieuwste handleidingen voor Multimeter

Owon HDS100 Handleiding

21 December 2024

IWH 73556 Handleiding

16 December 2024

Sanwa CD5001 Handleiding

7 December 2024

Megger AVO 415 Handleiding

7 December 2024

Metrix MX5006 Handleiding

5 December 2024

Metrix MX5060 Handleiding

5 December 2024

Velleman VTTEST11N Handleiding

3 December 2024

Abus AirSecure CO2WM110 Handleiding

2 December 2024

Kyoritsu KEW 6010B Handleiding

1 December 2024

Kyoritsu KEW-2046R Handleiding

1 December 2024