Apc SRTG192XLBP4 Handleiding

Apc UPS SRTG192XLBP4

Lees hieronder de 📖 handleiding in het Nederlandse voor Apc SRTG192XLBP4 (28 pagina's) in de categorie UPS. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/28

Important Safety Instructions

Read the instructions carefully and look at the equipment to become familiarse

with the device before trying to

install, operate, service or maintain it. The

following special messages may appear throughout this document or on

the

equipment to warn of potential hazards or to call attention to information that

clarifies or simplies a procedure.

The addition of this symbol to either Danger or Warning safety label indicates a “ ” “ ”

that an electrical hazard exists which will

result in personal injury if the instructions

are not followed.

This is the safety alert symbol. It is used to alert you to potential

personal injury

hazards. Obey all safety messages that follow

this symbol to avoid possible injury or

death.

DANGER

DANGER will result inindicates a hazardous situation which, if not avoided, death or serious injury.

WARNING

indicates

hazardous

situation

which,

not

avoid ,ed

coul r ultd es

death

serious

injury.

CAUTION

i icatesnd

hazard sou

sit tionua

which,

not

avoi ,ded

c l r ultou d es

mi rno

moderate

injury.

NOTICE

used

address

practices

not

ph alysic

injury.

Product Handling Guidelines

Installation Guide Smart-UPS

™

External Battery Module SRTG192XLBP4

2 Smart-UPS External Battery Module SRTG192XLBP4 RT

Safety and General Information

•

Adhere to all national and local electrical codes.

•

Changes and modications to this unit not expressly approved by APC by Schneider Electric could void the

warranty.

•

This unit is intended only for indoor use in a controlled environment.

•

Do not operate this unit in direct sunlight, in contact with uids, or where there is excessive dust or humidity.

•

Be sure the air vents on the unit are not blocked. Allow adequate space for proper ventilation.

•

Before installing or replacing the batteries, remove jewelry such as wristwatches and rings. High, short circuit

current through conductive materials could cause severe burns.

•

The battery typically lasts for two to five years. Environmental factors impact battery life.

•

Elevated ambient temperatures, poor quality mains power, and frequent short duration discharges will shorten

battery life.

•

The equipment is heavy. Always practice safe lifting techniques adequate for the weight of the equipment.

•

The batteries are heavy. Remove the batteries before installing UPS and external battery modules in a rack.the

•

Always install XLBPs at the in the bottom rack-mount congurations. The UPS must installed above be

XLBPs.

•

Do not dispose of batteries by burning them. The batteries may explode.

•

Do not open or mutilate batteries. Released electrolyte is harmful to the skin and eyes, and may be toxic.

•

Always recycle used batteries.

•

Recycle the package materials or save them for reuse.

•

Additional safety information can be found in the Safety Guide supplied with this unit.

•

A battery can present a risk of electric shock and burns by high short-circuit current.

•

Failed batteries can reach temperatures that exceed the burn thresholds for touchable surfaces.

Battery safety

CAUTION

RRIS

ISISK

OOF

FAFAL

LLL

LLIN

INING

OOB

BBJ

JJE

EEC

CCT

TTS

•

Each battery module weighs 16.5 (36.4 lb). kg

•

Always practice safe lifting techniques adequate for the weight of the equipment.

•

Remove the battery modules before installing the XLBP.

•

Use the battery module handle to carefully slide the battery modules in or out of the XLBP.

•

Do not use the battery module handle to lift or carry the battery module.

Failure to f

Failure to fFailure to follow these instr

ollow these instr

ollow these instrollow these instructions ca

uctions ca

uctions cauctions can result in equi

n result in equi

n result in equin result in equipment dam

pment dam

pment dampment dama

aage and minor or m

ge and minor or m

ge and minor or mge and minor or moderate injury.

oderate injury.

oderate injury.oderate injury.

CAUTION

RRIS

ISISK

OOF

FF H

H HYD

YDYDR

RRO

OOG

GGEN

ENEN

SSU

UULP

LPLPH

HHID

IDIDE

EE G

G GA

AAS

S S A

AAN

NND

DD E

E EX

XXC

CCE

EES

SSS

SSIV

IVIVE

E E S

SSM

MMO

OOK

KKE

•

Replace the battery at least every 5 years at the end of its service life, whichever is earlier. or

•

Replace the battery immediately when the UPS indicates battery replacement is necessary.

•

Replace batteries with the same number and type of batteries as originally installed in the equipment.

•

Replace the battery immediately when the UPS indicates a battery over-temperature condition, or when there is evidence of

electrolyte leakage. Power off the UPS, unplug it from the AC input, and disconnect the batteries. Do not operate the UPS until the

batteries have been replaced.

•

*Replace all battery modules (including the modules in External Battery Packs) which are older than one year, when installing

additional battery packs or replacing the battery module(s).

Failure to f

Failure to fFailure to follow these instr

ollow these instr

ollow these instrollow these instructions ca

uctions ca

uctions cauctions can result in

n result in

n result inn result in minor or

minor or

minor or minor or moderate injury

moderate injury

moderate injurymoderate injury and equipme

and equipme

and equipme and equipment damage.

nt damage.

nt damage.nt damage.

* Contact APC by Schneider Electric Worldwide Customer Support to determine the age of the installed battery modules.

Smart-UPS

External Battery Module SRTG192XLBP4 3 RT

Package Contents

Inspect the contents upon receipt. Notify the carrier and dealer if there is damage.

Included with all models

Front bezel

M5 Floating nut to secure

the battery pack to the rack

（

）

M4x6 at head screws to

secure the rack-mount

brackets to the UPS.

（

）

M5x12 Phillips at head

screw to secure the XLBP

to the rack

（

）

Battery connector holder

（

）

Ground cable 0.74 m

（

）

Battery wire 0.64 m

Connect UPS and battery

pack

(x1)

Stabilizer bracket

connectors

（）x6

tabilizer bracket

（

x2 pairs

）

Rack-mount brackets

（

x1pair

）

Installation manual

（

）

Packing list

（

）

Change the connector holder the battery cable to connect one battery pack to another battery packof

❶ Remove the screw and

connector

holder.

❷ Change the connector holder.

❸ Secure the

connector holder

with screws 2

Product specificaties

Merk:	Apc
Categorie:	UPS
Model:	SRTG192XLBP4
Kleur van het product:	Zwart
Gewicht:	91000 g
Breedte:	440 mm
Diepte:	683 mm
Hoogte:	130 mm
Gewicht verpakking:	101500 g
Breedte verpakking:	580 mm
Diepte verpakking:	780 mm
Hoogte verpakking:	335 mm
Vormfactor:	Rackmontage
Accu/Batterij voltage:	192 V
Uitgangsvermogen:	- W
Frequentie:	- Hz
Luchtvochtigheid bij opslag:	0 - 95 procent
Hoogte, in bedrijf:	0 - 2011.68 m
Hoogte bij opslag:	0 - 15240 m
Rackcapaciteit:	3U
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 95 procent
Batterijtechnologie:	Sealed Lead Acid (VRLA)
Output power capacity:	- kVA
Ingang operation voltage (min):	- V
Ingang operation voltage (max):	- V
Acculevensduur (max):	5 jaar