Apc MGE Galaxy 3500 Handleiding

Apc UPS MGE Galaxy 3500

Lees hieronder de 📖 handleiding in het Nederlandse voor Apc MGE Galaxy 3500 (12 pagina's) in de categorie UPS. Deze handleiding was nuttig voor 18 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

990-1957A-001 4/2009

*990-1957A-

Installation

MGE™ Galaxy™ 3500

10-30 kVA 208/220 V with batteries

IMPORTANT SAFETY INSTRUCTIONS

- SAVE THESE INSTRUCTIONS

Warning: ALL safety instructions in the Safety Sheet

(990-2940) must be read, understood and followed when

installing the UPS system. Failure to do so could result in

equipment damage, serious injury, or death.

Warning: After the UPS has been electrically wired, do

not start it up. Start-up is commissioned to authorized

personnel from Schneider Electric.

Caution: All electrical power and power control wiring

must be installed by a qualified electrician, and must comply

with local and national regulations for maximum power

rating.

Note: Ensure that the unit is in its final location prior to

installation.

Note: Battery and utility power must not be connected until

all other wiring has been completed.

See Also: For parallel configurations see manual 990-

3568.

Level the Enclosure

Warning: The system must be installed on a level floor.

The leveling feet will stabilize the enclosure, but will not

account for a badly sloped floor.

 Use a 13/14 mm wrench to adjust the four leveling feet.

 Ensure that the system is level.

Caution: Do not move the enclosure after the leveling feet

have been lowered.

Floor Anchoring (if applicable)

Anchor the UPS enclosure to the floor

Note: Floor-anchoring bolts are not provided with the UPS.

Purchase the bolts locally (minimum size: M8). Follow the

specifications given by the manufacturer of the floor

anchoring system when bolting the UPS system to the floor.

 Reuse the two transport brackets (one

on each side) that were used to secure the

UPS to the pallet during transport.

 Drill two to six holes in the floor for

each bracket. Attach with bolts.

Prepare for Cables

Bottom cable entry

 From the rear of the UPS, loosen the six

M4 screws from the upper cover (the cable

landing area), and remove. Save the screws

for later use.

 Loosen the two M4 screws (one on each

side) from the top part of the conduit box.

Loosen the M4 screws attaching it to the

bottom part (two screws in a 352 mm (13.8

in) enclosure), (three screws in a 523 mm

(20.50 in) enclosure) and remove. Save the

screws for later use.

 Loosen the four M4 screws (two on each

side) from the conduit box bottom and

remove. Save the screws for later use.

 Punch as many holes as

needed in the marked areas

of the bottom conduit box.

 Attach the conduit box

bottom to the enclosure

(reuse the screws from step

.

 Attach conduits to the

conduit box.

 Run the cables through

the conduits, the bottom of

the conduit box, and up into

the cable landing area.

 Attach the conduit box top to the conduit box bottom, and to the

enclosure reusing the screws from step .

 Fasten the cables with cable ties.

UPS

UPS XR battery enclosure

















Bypass

Output

Battery

Mains













Connect the AC Input and AC

Output Cables

Warning: Use compression type lugs ONLY.

Do not loosen or add cables to any factory preinstalled

cables on busbars. Use upper part of busbar for

connection only.

Single mains

 Connect the AC input cables

and the neutral to the input

cable landings.

 Connect the AC output

cables and the neutral to the

output cable landings.

 Connect the ground cables to

the studs (earth symbol

beneath) using a screw.

Dual mains Connect the DC Battery Cables

(if applicable)

 Connect battery

cables BAT+, BAT–, and

N to the battery cable

landings.

Connect the Communication

Cables

Warning: Make sure that the UPS is completely OFF as

the connectors are very close to the power busbars.

J106 and J108 pin connections

Note: The UPS must be connected to either a dry contact or

a 24 VDC EPO (Emergency Power Off) switch.

Note: The external EPO +24 VDC, 1500 mA circuit can be

supplied through other vendors.

Note: Always follow the pin connection procedures from

the top and work down: J106 (8-1), J108 (1-6).







 Remove the

three busbars A,

B, and C by

removing two M6

screws from each

busbar.

 Connect the AC

input cables and

the neutral to the

input cable

landings.

 Connect the

bypass cables and

the neutral to the

bypass cable

landings.

 Connect the

output cables and

the neutral to the

output cable

landings.

 Connect the

ground cables to

the studs (earth

symbol beneath)

using a screw.











J108 pin connections:

1 Normally open EPO

2 Normally open EPO return

3 Normally closed EPO

4 Normally closed EPO return

5 +24 V SELV supply

6 SELV ground







J106 pin connections:

8 Ext. charging control return

7 External control of charging

6 Q3 active return

5 Q3 active

4 Battery measurement supply*

3 Battery unit quantity*

2 Max. battery temperature*

1 Battery measurement return*

* Should be used with APC XR

Enclosures



Product specificaties

Merk:	Apc
Categorie:	UPS
Model:	MGE Galaxy 3500
Gewicht:	776000 g
Temperatuur bij opslag:	0 - 30 °C
Kleur kabel:	Grijs
Luchtvochtigheid bij opslag:	0 - 85 procent
Afmetingen (B x D x H):	523 x 925 x 1499 mm
AC-ingangsspanning:	208/400 V
AC-ingangsfrequentie:	50 - 60 Hz
Bedrijfstemperatuur (T-T):	-5 - 45 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 85 procent