Apc BVS240XDPDR Handleiding

Apc UPS BVS240XDPDR

Lees hieronder de 📖 handleiding in het Nederlandse voor Apc BVS240XDPDR (2 pagina's) in de categorie UPS. Deze handleiding was nuttig voor 8 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Safety and General Instructions

SAVE THESE INSTRUCTIONS - This manual contains important instructions that should

be followed during installation and maintenance of the product.

Read the user documentation to become familiar with the equipment before

trying to install or operate it.

• Switch off the input power before connecting or disconnecting the wires.

• Use RED color wire for +ve and BLACK color wire for –ve connections.

• Use insulated pin type lugs to be sure that the wire strands do not touch any metallic

surface during connection/disconnection.

• Be sure that the wires do not touch any metallic surface during connection/

disconnection.

• Be sure to connect the wires to the power supply unit first and then to battery pack(s).

• While disconnecting wires, be sure to disconnect the wires at battery pack(s) first and

then at the power supply unit.

• Allow a minimum space of 50 mm above the unit, 180 mm below the unit and 10 mm

lateral distance from other devices to be sure of sufficient cooling.

• CAUTION: The enclosure can reach temperatures that exceed the burn thresholds for

touchable surfaces, depending on the ambient temperature and load.

• Do not introduce any objects into the power supply unit.

Specifications

Environmental

Physical

Input

Output

Certification and Standards

IEC/EN/BS/UL 62368-1, CSA-C22.2 No. 62368-1, IEC/EN 60950-1, UL 508,

CSA C22.2 No. 14, IEC/EN 61010-1.

cTUVus CE, UKCA, GB 4943.1, CQC, EN 55032, EN55035, EN IEC 61000-6-2,

EN IEC 61000-6-4, EN IEC 61204-3, FCC 47 CFR Part 15, Subpart B & ICES-003 Issue 7

Front Panel Features

Installation

Mounting

NOTE: Be sure that the input/output terminal block is at the bottom while mounting the

power supply unit on a 35 mm DIN rail.

1. Locate the top hook of the rail

mounting system (on the unit)

with the unit slightly tilted

upwards.

2. Rotate the unit in clockwise

direction till the latch of the rail

mount system snaps on to the

DIN rail and the unit cannot be

rotated any further.

3. Shake the unit slightly to be

sure that it is securely mounted

on the DIN rail.

Dismounting

1. Release the latch of the rail

mount system (on the unit) by

pulling it downwards using a

screw driver.

2. Tilt the unit upwards till the latch

is free from the DIN rail.

3. Slide the unit upwards till the

top hook gets free from the DIN

rail.

Dry contact details

All dry contacts (Pin3 to Pin10) are normally closed during operation and will open during

an event.

NOTE:

• NC = Normally Closed; NO = Normally Open; NA = Not Applicable.

• To insert wires into the Dry Contact terminals, press the locking lever (

) using a

suitable screwdriver and insert the wire into the terminal (). Remove the screwdriver

to secure the wire to the terminal.

Ambient temperature Operating –15 to +50 °C

Storage –15 to +70 °C

Humidity 5 to 95% (Non condensing)

Altitude Operating 3000 m (Max.)

Storage 3000 m (Max.)

Audible Noise < 40 db

International Protection Code IP 20

Operating Protection Class Class II

Dimensions without packaging (H x W x D) 129 x 40 x 119 mm

(5.08 x 1.57 x 4.69 in)

Dimensions with packaging (H x W x D) 190 x 57x 188 mm

(7.47 x 2.23 x 7.39 in)

Weight without packaging 0.5 kg

(1.1 lb)

Weight with packaging 0.7 kg

(1.54 lb)

240 W 480 W

Model BVS240XDPDR BVS480XDPDR

Nominal input voltage 24 VDC

Voltage Range 21.6 – 28.6 VDC

Nominal Current 10 A 20 A

Runtime at full load (with 1 battery pack) 10 min at 10 A load 3 min at 20 A load

Efficiency at Nominal Voltage (Bypass mode,

battery fully charged) >95%

Over current / Short circuit protection 40 A Fuse

240 W 480 W

Nominal output voltage UN / tolerance 24 VDC

Switch On time (On delay time typical) < 1 s

Output current 10 A 20 A

Output over current limit 10.5 A< OCP<13 A 20.5 A<OCP<26 A

Short circuit protection Yes

Over temperature protection Yes

No. of units series connection No

No. of units parallel connection No

(+) Battery terminal

(–) Battery terminal

(–) Output terminal

(+) Output terminal

(–) Input terminal

(+) Input terminal

Dry contact terminals

Status LED - Red

Status LED - Green

240 W 480 W

oem0343a

Pin1 Remote On/Off. Connect Normally Open

Push to On button to this contact.

Pin2

Pin3 On-Battery mode

Pin4

Pin5 Replace battery

Pin6

Pin7 Battery disconnected

Pin8

Pin9 Low battery

Pin10

Locking lever

Terminal

Mode of Operation →Line

Mode

Battery

Mode

Battery Mode

Low Battery

Line Mode

Battery disconnected

Replace

Battery

Condition ↓

Remote On/Off NA NA NA NA NA

On-Battery NC NO NO NC NC

Replace Battery NC NC NC NC NO

Battery Disconnected NC NC NC NO NC

Low Battery NC NC NO NC NC

oem0344a

oem

0345a

 

oem0346a

User Manual Easy UPS DIN Rail

Mount DC to DC Power Supply

BVS240XDPDR/BVS480XDPDR

Customer support and warranty information is available at www.se.com.

the Schneider Electric logo, are trademarks of Schneider Electric SE, its

subsidiaries or affiliated companies. All other brands may be trademarks of

their respective owners.

990-6465B

03/2022

Connect Input, Output and Battery

Recommended wire sizes and tightening torque

NOTE:

• Be sure to use a Pin Type cable lug for connecting the Input,

Output and Battery wires.

• To be sure of a secure connection, the wire insulation should be

stripped (S) for approx. 6 mm,

Be sure that all the strands are completely enclosed in the lug.

• Be sure that the positive and negative polarity wires are connected to the respective

terminals on the power supply unit and the battery pack.

1. Connect the DC Input wires to the input terminals (refer “Front Panel Features” for

details).

2. Connect the output wires to the output terminals (refer “Front Panel Features” for

details).

3. Connect the battery wires to the battery terminals (refer “Front Panel Features” for

details).

NOTE:

• Be sure to connect the wires first to the terminals on the power supply unit and then to

the terminals on the battery pack(s).

• A maximum of 4 battery packs can be connected to a power supply unit.

Start up

NOTE: Be sure that the load is connected to the UPS before turning On the DC input.

Turn On the DC to DC Power Supply in On-Line mode

The power supply unit turns on automatically when the DC input is applied to the input

terminals.

Turn On the DC to DC Power Supply in On-Battery mode

Press the REMOTE /ON OFF Push to On button, to turn on the power supply unit in On-

Battery mode.

Turn off the DC to DC Power Supply

To turn Off, press the REMOTE ON/OFF push button.

Status Indicators

Limited Factory Warranty

Schneider Electric IT Corporation (SEIT), warrants its products to be free from defects in

materials and workmanship for a period of TWO (2) years. The SEIT obligation under this

warranty is limited to repairing or replacing, at its own sole option, any such defective

products. Repair or replacement of a defective product or part thereof does not extend the

original warranty period.

This warranty applies only to the original purchaser who must have properly registered the

product within 10 days of purchase. Products may be registered online at

warranty.apc.com.

SEIT shall not be liable under the warranty if its testing and examination disclose that the

alleged defect in the product does not exist or was caused by end user or any third person

misuse, negligence, improper installation, testing, operation or use of the product contrary

to SEIT recommendations of specifications. Further, SEIT shall not be liable for defects

resulting from: 1) unauthorized attempts to repair or modify the product, 2) incorrect or

inadequate electrical voltage or connection, 3) inappropriate on site operation conditions,

4) Acts of God, 5) exposure to the elements, or 6) theft. In no event shall SEIT have any

liability under this warranty for any product where the serial number has been altered,

defaced, or removed.

EXCEPT AS SET FORTH ABOVE, THERE ARE NO WARRANTIES, EXPRESS OR

IMPLIED, BY OPERATION OF LAW OR OTHERWISE, APPLICABLE TO PRODUCTS

SOLD, SERVICED OR FURNISHED UNDER THIS AGREEMENT OR IN CONNECTION

HEREWITH.

SEIT DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY,

SATISFACTION AND FITNESS FOR A PARTICULAR PURPOSE.

SEIT EXPRESS WARRANTIES WILL NOT BE ENLARGED, DIMINISHED, OR

AFFECTED BY AND NO OBLIGATION OR LIABILITY WILL ARISE OUT OF, SEIT

RENDERING OF TECHNICAL OR OTHER ADVICE OR SERVICE IN CONNECTION

WITH THE PRODUCTS.

THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND IN LIEU OF

ALL OTHER WARRANTIES AND REMEDIES. THE WARRANTIES SET FORTH ABOVE

CONSTITUTE SEIT'S SOLE LIABILITY AND PURCHASER EXCLUSIVE REMEDY FOR

ANY BREACH OF SUCH WARRANTIES. SEIT WARRANTIES EXTEND ONLY TO

ORIGINAL PURCHASER AND ARE NOT EXTENDED TO ANY THIRD PARTIES.

IN NO EVENT SHALL SEIT, ITS OFFICERS, DIRECTORS, AFFILIATES OR

EMPLOYEES BE LIABLE FOR ANY FORM OF INDIRECT, SPECIAL,

CONSEQUENTIAL OR PUNITIVE DAMAGES, ARISING OUT OF THE USE, SERVICE

OR INSTALLATION OF THE PRODUCTS, WHETHER SUCH DAMAGES ARISE IN

CONTRACT OR TORT, IRRESPECTIVE OF FAULT, NEGLIGENCE OR STRICT

LIABILITY OR WHETHER SEIT HAS BEEN ADVISED IN ADVANCE OF THE

POSSIBILITY OF SUCH DAMAGES. SPECIFICALLY, SEIT IS NOT LIABLE FOR ANY

COSTS, SUCH AS LOST PROFITS OR REVENUE, WHETHER DIRECT OR INDIRECT,

LOSS OF EQUIPMENT, LOSS OF USE OF EQUIPMENT, LOSS OF SOFTWARE, LOSS

OF DATA, COSTS OF SUBSTITUANTS, CLAIMS BY THIRD PARTIES, OR

OTHERWISE.

NOTHING IN THIS LIMITED WARRANTY SHALL SEEK TO EXCLUDE OR LIMIT OR

DEATH OR PERSONAL INJURY RESULTING FROM ITS NEGLIGENCE OR ITS

FRAUDULENT MISREPRESENTATION OF TO THE EXTENT THAT IT CANNOT BE

EXCLUDED OR LIMITED BY APPLICABLE LAW.

To obtain service under warranty you must obtain a Returned Material Authorization (RMA)

number from customer support. Customers with warranty claims issues may access the

SEIT worldwide customer support network through the APC by Schneider Electric Web

site: www.apc.com. Select your country from the country selection drop down menu. Open

the Support tab at the top of the web page to obtain information for customer support in

your region. Products must be returned with transportation charges prepaid and must be

accompanied by a brief description of the problem encountered and proof of date and place

of purchase.

Schneider Electric Worldwide

Customer Support

Customer support for this or any other Schneider Electric product is available at no charge

in any of the following ways:

• Visit the Schneider Electric Web site to access documents in the Schneider Electric

Knowledge Base and to

– submit customer support requests.

– www.schneider-electric.com (Corporate Headquarters)

Connect to localized Schneider Electric Web sites for specific countries, each of which

provides customer support information.

– www.schneider-electric.com/support/

Global support searching Schneider Electric Knowledge Base and using e-support.

• Contact Schneider Electric IT (SEIT) Customer Support Center by telephone or

e-mail.

– Local, country specific centers: go to www.schneider-electric.com/support/contact

for contact information.

For information on how to obtain local customer support, contact the Schneider Electric

representative or other distributor from whom you purchased your Schneider Electric

product.

CAUTION

RISK OF EQUIPMENT DAMAGE

• Wiring should be performed by a qualified electrician.

• Wire size must comply with required current capacity as well as national and local

electrical codes.

• Be sure to turn Off the input power supply before connecting or disconnecting input,

output and battery wires to the terminals.

• Be sure that the wires do not touch each other or any metal object during

connection/disconnection.

• Be sure to connect the battery wires first to the power supply unit and then to the

battery.

• Be sure to disconnect wires first from the battery and then from the power supply

unit.

• Be sure to crimp pin type lugs to the input, output and battery wires to prevent loose

strands from touching any metal object.

Failure to follow these instructions can result in equipment damage and

minor or moderate injury.

Wire Size

Torque

240 W 480 W

Input/Output 16 AWG (1.307 mm2)12 AWG (3.310 mm2) 0.8 N m

Dry Contacts 26 AWG (0.128 mm2) Not Applicable

Remote On/Off

Battery 12 AWG (3.310 mm2)0.8 N m

Green LED Red LED UPS Status

Illuminated Power supply unit is in on-line mode and the

battery is charging/charged.

Flashes 1 sec on

and 1 sec off Power supply unit is in on-battery mode.

Flashes 0.3 sec on

and 0.3 sec off Low battery alert.

Flashes 1 sec on

and 1 sec off An over current event has occurred.

Illuminated Power supply unit has tripped due to an over

voltage event.

Flashes An over temperature event has occured.

Green LED Red LED UPS Status

Product specificaties

Merk:	Apc
Categorie:	UPS
Model:	BVS240XDPDR
Kleur van het product:	Grijs
Gewicht:	500 g
Breedte:	40 mm
Diepte:	129 mm
Hoogte:	119 mm
Uitgangsvermogen:	240 W
Code geharmoniseerd systeem (HS):	85078000
Output power capacity:	0.24 kVA
Ingang operation voltage (min):	21.6 V
Ingang operation voltage (max):	28.6 V
Uitgang operation voltage (min):	24 V
Uitgang operation voltage (max):	24 V